Engine Oil Pump - Remove
拆卸步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件说明 | 数量 |
| A | 1P-0510 | 起子总成 | 1 |
开始:
- 拆下发动机油底壳。 请参阅拆解和组装, "发动机油底壳 - 拆卸和安装"。
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
| 注意 |
|---|
在检验、保养、测试、调整及维修产品时，务必留心，确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前，要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品，参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 拆下螺栓 (1) 。
Show/hide table
 | |
| 图 1 | g01151740 |
- 拆下螺栓 (2) 。
- 拆下螺栓 (3) 和发动机机油泵 (4) 。
- 拆下缸体与排气弯头之间的 O 形密封圈。
- 卸下螺栓 (5) ，然后卸下排气弯头 (6) 。
Show/hide table
 | |
| 图 2 | g01152424 |
- 拆下螺栓 (7) 。 拆卸机油吸油管 (8) 和密封垫。
- 拆下螺栓 (12) 和垫圈。 拆卸惰齿轮 (11) 。 使用工具 (A) 从惰齿轮 (11) 上拆卸轴承 (10) 。 从发动机机油泵 (4) 上拆下轴 (9) 。
Show/hide table
 | |
| 图 3 | g01152433 |
Caterpillar Information System:
C9 Engines for Caterpillar Built Machines Engine Oil Filter Base - Disassemble
C27 and C32 Engines for Caterpillar Built Machines Fuel Temperature Sensor - Remove and Install
C9 Generator Set Engines Flywheel Housing
2005/05/02 Improved Turbochargers are Available {1052}
C9 Engines for Caterpillar Built Machines Engine Oil Filter Base and Oil Cooler - Install
C3.3 and C4.4 Generator Sets Additional Messages
C27 and C32 Generator Set Engines Engine Oil Pressure Sensor - Remove and Install
2005/03/21 The MIDS Display is Replaced by the Advisor Monitor Display {7490}
C7 and C9 Marine Engines CID 1249 FMI 08 Secondary Throttle Position signal abnormal
C7 and C9 Marine Engines CID 0164 FMI 11 Injector Actuation Pressure system fault
3126B Industrial Engines CID 0164 FMI 04 Injector Actuation Pressure voltage low
3126B Marine Engines CID 0127 FMI 04 Transmission Oil Pressure short to ground
C27 and C32 Engines for Caterpillar Built Machines Turbocharger Outlet Pressure Sensor - Remove and Install
C9 Engines for Caterpillar Built Machines Water Pump - Remove
C27 and C32 Engines for Caterpillar Built Machines Inlet Air Temperature Sensor - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install
C9 Engines for Caterpillar Built Machines Water Pump - Install
C27 and C32 Engines for Caterpillar Built Machines Electronic Control Module - Remove and Install
854K Wheel Dozer and 992K Wheel Loader Alternator - Remove and Install
854K Wheel Dozer and 992K Wheel Loader Electric Starting Motor - Remove and Install
C9 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C9 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
C9 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove
C9 Engines for Caterpillar Built Machines Crankshaft Front Seal - Install