2005/03/21 Caterpillar


The MIDS Display is Replaced by the Advisor Monitor Display {7490}

Usage:

G3612 1YG
Engine:
G3520B (S/N: GET1-UP)
G3606 (S/N: 3XF1-UP)
G3608 (S/N: 4WF1-UP; BEN1-UP)
G3612 (S/N: BKE1-UP; 1YG1-UP)
G3616 (S/N: BLB1-UP; 4CG1-UP)

Description of Change: The MIDS display is being replaced by the Advisor Monitor Display on the above G3500 and G3600 Engines that have the Advanced Digital Engine Management III (ADEM III) Electronic Control Module.

Adaptable To: The 168-5274 Display Module Gp is being cancelled and replaced by the following two displays.

  • 266-0269 Monitor Service Electronic Control Module

  • 266-0270 Monitor Service Electronic Control Module

The 266-0269 Monitor Service Electronic Control Module contains the 255-8937 Engine Electronic Control Gp (Advisor Monitor Display). This display is used on G3600 Engines that are programmed with the 266-1639 Monitor Software Gp (flash file).

The 266-0270 Monitor Service Electronic Control Module contains the 255-8937 Engine Electronic Control Gp (Advisor Monitor Display). This display is used on G3500 Engines that are programmed with the 218-7530 Monitor Software Gp (flash file).

The Advisor Monitor Display has the same screen displays and the same keypad as the MIDS display. The display in the 266-0269 Monitor Service Electronic Control Module and the 266-0270 Monitor Service Electronic Control Module is slightly larger than the display in the 168-5274 Display Module Gp. To facilitate the larger size, the 204-6689 Control Panel Box Gp is being cancelled and replaced by the following box groups:

The 257-5889 Control Panel Gp is for use with G3600 Engines. The 260-0862 Box is for use with G3500 Engines.

Field Replacement

For field replacement of the 168-5274 Display Module Gp, the cutout in the door of the 204-6689 Control Panel Box Gp must be enlarged. Refer to Special Instruction, REHS2347 for additional details.

The 266-2501 Communication Installation Gp provides the mounting hardware that is required for installing either of the above monitors. Table 1 lists the parts that are contained in the 266-2501 Communication Installation Gp.

Table 1
266-2501 Communication Installation Gp    
Qty     Part Number     Description    
1     248-5563     Gasket    
2     260-0405     Bracket As    
4     260-0406     Bolt    
4     260-0407     Cap    
1     260-0864     Monitor Harness As    
1     230-0975     Warning Plate    
10     3S-2093     Cable Strap    

The new displays are adaptable to the Engines that are listed above.

Caterpillar Information System:

C7 and C9 Marine Engines CID 1249 FMI 08 Secondary Throttle Position signal abnormal
C7 and C9 Marine Engines CID 0164 FMI 11 Injector Actuation Pressure system fault
3126B Industrial Engines CID 0164 FMI 04 Injector Actuation Pressure voltage low
3126B Marine Engines CID 0127 FMI 04 Transmission Oil Pressure short to ground
3126B Marine Engines CID 0127 FMI 03 Transmission Oil Pressure open/short to +batt
Cleaning the Engine Mounted Heat Exchanger{1379} Cleaning the Engine Mounted Heat Exchanger{1379}
C27 and C32 Engines for Caterpillar Built Machines Coolant Temperature Sensor - Remove and Install
3126B Industrial Engines CID 0094 FMI 03 Fuel Pressure open/short to +batt
C9 Engines for Caterpillar Built Machines Engine Oil Filter Base and Oil Cooler - Remove
C27 and C32 Generator Set Engines Crankshaft Position Sensor - Remove and Install
C7 and C9 Marine Engines Diagnostic Code Cross Reference
C27 and C32 Generator Set Engines Camshaft Position Sensor - Remove and Install
C27 and C32 Generator Set Engines Engine Oil Pressure Sensor - Remove and Install
C3.3 and C4.4 Generator Sets Additional Messages
C9 Engines for Caterpillar Built Machines Engine Oil Filter Base and Oil Cooler - Install
2005/05/02 Improved Turbochargers are Available {1052}
C9 Generator Set Engines Flywheel Housing
C27 and C32 Engines for Caterpillar Built Machines Fuel Temperature Sensor - Remove and Install
C9 Engines for Caterpillar Built Machines Engine Oil Filter Base - Disassemble
C9 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C27 and C32 Engines for Caterpillar Built Machines Turbocharger Outlet Pressure Sensor - Remove and Install
C9 Engines for Caterpillar Built Machines Water Pump - Remove
C27 and C32 Engines for Caterpillar Built Machines Inlet Air Temperature Sensor - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.