Alternator - Remove and Install
Show/hide table
不断开蓄电池可能会造成人身伤害。 先断开蓄电池负极电缆。 然后断开蓄电池正级电缆。 如果没有断开蓄电池的话,正极电源线可能会产生花火。 火花可能会导致蓄电池爆炸或起火。 |
- 将蓄电池断路开关转到断开位置。
- 在连接到交流发电机的线束组件上作一个识别标记以便于安装。 从交流发电机上断开线束组件。
Show/hide table
图 1 g01092353 - 松开调节杆 (8) 上的螺母 (7)。
- 松开螺栓 (3) 上的螺母。 将交流发电机的底部推向缸体。 拆下交流发电机皮带轮上的 V 型皮带。
- 拆下螺栓 (3) 和螺栓 (6)。 拆下交流发电机 (4)。
- 将螺母 (5) 和交流发电机皮带轮从交流发电机上拆下。
- 拆下螺母 (1) 和支架 (2)。
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 155-0695 | 螺纹锁固胶 | - |
- 安装交流发电机皮带轮和螺母 (5)。 拧紧螺母至扭矩为
102 ± 7 N·m (75 ± 5 lb ft) 。 - 将支架 (2) 在螺柱上安置到位。 将工具 (A) 涂抹在螺柱的螺纹上。 安装螺栓 (1),并拧紧至扭矩为
70 ± 5 N·m (52 ± 4 lb ft) 。 - 将交流发电机 (4) 在支架 (2) 上安置到位并安装螺栓 (3)。
- 将调节杆 (8) 定位到交流发电机上后安装螺栓 (6)。
- 安装 V 形皮带。 张紧 V 形皮带。 请参阅测试与调整, "皮带张紧度表"。
- 拧紧螺母 (7) 至扭矩为
30 ± 15 N·m (22 ± 11 lb ft) 。 - 将线束组件连接到交流发电机上。 上紧螺母。 有关扭矩值,请参阅技术规格, "交流发电机"。
- 将蓄电池断路开关转到接通位置。
Show/hide table
图 2 | g01092353 |
Caterpillar Information System:
G3500 Generator Sets Cooling System Coolant (NGEC) - Change
C13, C15, and C18 Generator Set Engines Speed Control (Switch) - Test
C15 and C18 Industrial Engines Camshaft - Remove
C15 and C18 Industrial Engines Camshaft - Install
G3500 Engines Starting the Engine
C18 Generator set and C18 Marine Engines Flywheel - Install
C18 Generator set and C18 Marine Engines Flywheel - Remove
C13, C15, and C18 Tier 4 Final Engines Electronic Unit Injector
C3.3 Industrial Engine Engine Air Cleaner Element (Single Element) - Inspect/Replace
C15 Petroleum Generator Set Engines Fuel Transfer Pump
XQ125 Generator Set Driven Equipment - Check
C15 and C18 Industrial Engines Flywheel Housing - Remove and Install
3500 and 3500B Engines Electrical System
3516B and 3516B High Displacement Engines for 994D and 994F Wheel Loaders Crankcase Pressure Sensor
3500B and 3500C Marine Engines Turbocharger Inlet Pressure Sensor
C15 and C18 Industrial Engines Electric Starting Motor - Remove and Install
G3612 and G3616 Engines Safety Messages
C15 and C18 Industrial Engines Engine Oil Filter Base - Remove
C15 and C18 Industrial Engines Engine Oil Filter Base - Install
3412E, C30 and C32 Marine Engines Engine Oil Pump - Remove
3412E, C30 and C32 Marine Engines Engine Oil Pump - Disassemble
C15 and C18 Industrial Engines Engine Oil Cooler - Remove
C15 and C18 Industrial Engines Engine Oil Cooler - Install
2004/08/01 A New Exhaust Seal is Used {1059}