Flywheel - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 138-7573 | 提升支架 | 2 |
B | - | 导向螺柱 5/8 - 18 x 8 in |
2 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 加热齿圈 (3)。 将齿圈 (3) 安装在飞轮 (2) 上。
Show/hide table
图 2 g01091639 - 将工具 (B) 安装在曲轴中。
- 将工具 (A) 安装到飞轮 (2) 上。 使用适当的提升装置。 飞轮 (2) 的重量约为
44 kg (97 lb) 。 将飞轮安置在曲轴上。注: 安装时应使用新的螺栓。
- 将清洁的发动机机油涂抹在螺栓 (1) 的螺纹上。
- 安装螺栓 (1)。 拆下工具 (B)。 安装其余的螺栓 (1)。
- 拧紧螺栓 (1) 至扭矩为
270 ± 40 N·m (200 ± 30 lb ft) 。 - 将工具 (A) 从飞轮上拆下。
- 检查飞轮跳动。 请参阅测试与调整, "飞轮 - 检查"。
Show/hide table
图 1 | g01091705 |
注: 安装齿圈 (3) 的时候必须让轮齿斜面一侧朝上。 当飞轮安装完毕之后,轮齿斜面一侧应朝向起动马达。
Caterpillar Information System:
C18 Generator set and C18 Marine Engines Flywheel - Remove
C13, C15, and C18 Tier 4 Final Engines Electronic Unit Injector
C3.3 Industrial Engine Engine Air Cleaner Element (Single Element) - Inspect/Replace
C15 Petroleum Generator Set Engines Fuel Transfer Pump
XQ125 Generator Set Driven Equipment - Check
C15 and C18 Industrial Engines Flywheel Housing - Remove and Install
G3500 Engines Cooling System Coolant (NGEC) - Change
3500 Industrial Engines Auxiliary Water Pump
C7 Marine Engines Engine Sensors - Remove and Install
C7 Marine Engines Fuel Cooler - Remove and Install
C4.4 (Mech) Industrial Engine Battery or Battery Cable - Disconnect
C4.4 (Mech) Industrial Engine Battery - Replace
G3500 Engines Starting the Engine
C15 and C18 Industrial Engines Camshaft - Install
C15 and C18 Industrial Engines Camshaft - Remove
C13, C15, and C18 Generator Set Engines Speed Control (Switch) - Test
G3500 Generator Sets Cooling System Coolant (NGEC) - Change
C15 and C18 Industrial Engines Alternator - Remove and Install
3500 and 3500B Engines Electrical System
3516B and 3516B High Displacement Engines for 994D and 994F Wheel Loaders Crankcase Pressure Sensor
3500B and 3500C Marine Engines Turbocharger Inlet Pressure Sensor
C15 and C18 Industrial Engines Electric Starting Motor - Remove and Install
G3612 and G3616 Engines Safety Messages
C15 and C18 Industrial Engines Engine Oil Filter Base - Remove