Sprocket Shaft - Remove
拆卸步骤
Show/hide table
需要的工具     | |||
---|---|---|---|
工具     | 零件号     | 零件名称     | 数量     |
A     | 7F-9306     | 活动扳手     | 1     |
B     | 9U-6600     | 手动液压泵     | 1     |
9H-3992 | 导盖     | 1     | |
9S-8901 | 油缸总成     | 1     | |
7M-9772 | 销     | 2     | |
5P-4183 | 适配器     | 1     | |
7M-9774 | 连接器     | 1     | |
5S-1430 | 衬套     | 1     | |
5P-4181 | 适配器     | 1     | |
7M-9773 | 适配器     | 1     | |
C     | 9U-6600     | 手动液压泵     | 1     |
9H-3992 | 导盖     | 1     | |
9S-8901 | 油缸总成     | 1     | |
7M-9772 | 销     | 2     | |
5P-4183 | 适配器     | 1     | |
7M-9774 | 连接器     | 1     | |
5S-1430 | 衬套     | 1     |
开始:
- 拆卸终传动。 请参阅解体与组装, "终传动 - 解体"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 检查所有密封件和部件的状况。 如果任何零件磨损或损坏,则应使用新件更换。
- 拆卸环 (3) 和销 (1) 。
Show/hide table
图 1 | g01310135 |
Show/hide table
图 2 | g01310138 |
- 用工具 (A) 松开扳手螺母 (2) ,以便在扳手螺母 (2) 和转向离合器壳体之间的间隙为 3.20 mm (0.125 in)。
- 安装工具 (B) 。 按照如下步骤,拆卸标准尺寸链轮轴。
- 在链轮轴 (4) 的端部安装 5P-4183 适配器 (7) 。
注: 不要从链轮轴 (4) 上拆卸扳手螺母 (2) ,直到用工具 (B) 或工具 (C) 松开链轮轴 (4) 。 在从转向离合器壳体中的锥面上松开链轮轴 (4) 时,扳手螺母 (2) 将固定链轮轴 (4) 。
注: 使用工具 (B) ,拆卸标准尺寸链轮轴。 使用工具 (C) ,拆卸适用于低接地压力机器的链轮轴。
Show/hide table
图 3 | g01310141 |
Show/hide table
图 4 | g01310144 |
- 在油缸端部安装 7M-9774 连接器 。
- 如图所示,将 5S-1430 衬套 (11) 在链轮轴 (4) 上放置到位。
- 安装工具 (C) 。 使用如下步骤,拆卸适用于低接地压力机器的链轮轴。
- 在链轮轴端部安装 5P-4183 适配器 (13) 。
- 在链轮轴上滑入 5S-1430 衬套 (12) 。
- 在油缸总成上安装 9H-3992 导盖 (16) 。
Show/hide table图 6 g01310154
Show/hide table
图 5 | g01310150 |
- 将适当起吊设备连接至工具 (B) 或工具 (C) ,松开链轮轴。
- 拆卸工具 (B) 或工具 (C) ,拆卸适当起吊设备。
- 将适当起吊设备连在链轮轴 (4) 上。 链轮轴 (4) 的重量约为 45 kg (100 lb)。 使用适当的起吊设备完全拆卸链轮轴 (4) ,以便扳手螺母 (2) 可以与链轮轴 (4) 分离。
Show/hide table
图 7 | g01310166 |
Show/hide table
图 8 | g01309931 |
- 拆卸链轮轴 (4) 。
Caterpillar Information System:
992G Wheel Loader Machine Systems Boom - Remove
994D Wheel Loader Secondary Steering
615C Series II Wheel Tractor-Scraper Machine Systems Diverter Valve (Elevator) - Disassemble
966G Wheel Loader and 972G Wheel Loader Power Train Engine and Transmission Mounting
994D Wheel Loader Power Train Speed Sensor (Transmission Output)
D6G Track-Type Tractor Power Train Final Drive Gear, Idler Pinion and Bearings - Install
D250E Series II, D300E Series II, D350E Series II and D400E Series II Articulated Trucks Power Train Electronic Control System Backup Alarm
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Coolant Temperature Switch
994D Wheel Loader Power Train Temperature Sensor (Torque Converter Outlet Oil)
613C Series II Wheel Tractor-Scraper Machine Systems Elevator Control Valve - Assemble
994D Wheel Loader Power Train Torque Converter System Specifications
613C Series II Wheel Tractor-Scraper Machine Systems Elevator Control Valve - Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Crankshaft
D6G Track-Type Tractor Power Train Sprocket Shaft - Install
966G Wheel Loader and 972G Wheel Loader Power Train Drive Shaft
992G Wheel Loader Machine Systems Boom - Install
D6G Track-Type Tractor Power Train Final Drive Pinion and Flange - Remove
938G Wheel Loader and IT38G Integrated Toolcarrier Fire Extinguisher Location
631E Series II Wheel Tractor-Scrapers Ether Starting Aid Cylinder - Replace
D6G Track-Type Tractor Power Train Final Drive Pinion and Flange - Install
966G Wheel Loader and 972G Wheel Loader Machine Systems Vane Pump (Implement) - Remove
637E Series II Wheel Tractor-Scrapers Ether Starting Aid Cylinder - Replace
3512 Industrial Engine Fuel System - Prime
3176C and 3196 Engines for Caterpillar Built Machines Lubrication System