Exhaust Elbow - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
ZZ     | 6V-9830     | 盖组件     | 2     |
6V-9509 | 端面密封螺塞     | 2     |
注: 维修数据:拆卸和安装中的工具 (ZZ) 将不在图示中列出。 显示这一工具是为了协助有经验的维修人员。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 拆下管组件 (1) 。
Show/hide table
图 1 | g00978871 |
- 拆卸护罩组件 (4) 。
- 断开线束组件 (3) 。
- 拆下温度传感器 (2) 。
- 将工具 (A) 和适当的提升设备连接在排气弯头 (5) 上。
Show/hide table
图 2 | g00993513 |
- 拆下螺栓 (8) 和螺母 (6) 。
Show/hide table
图 3 | g00993514 |
- 卸下支架 (9) 。
- 将排气弯头 (5) 和密封垫从涡轮增压器 (7) 上拆下。 排气弯头的重量约为 45 kg (100 lb)。
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
B     | 4C-5599     | 防粘结剂     | 1     |
- 将工具 (A) 和适当的提升设备连接在排气弯头 (5) 上。
Show/hide table
图 4 | g00993513 |
- 将排气弯头 (5) 和密封垫置于涡轮增压器 (7) 上。 排气弯头的重量约为 45 kg (100 lb)。
Show/hide table
图 5 | g00993514 |
- 定位支架 (9) 。
- 在螺母 (6) 上涂抹工具 (B) 。
- 安装螺栓 (8) 和螺母 (6) 。
- 在温度传感器 (2) 上涂抹工具 (B) 。
Show/hide table
图 6 | g00978871 |
- 安装温度传感器 (2) 。 将温度传感器 (2) 上紧到 12 ± 3 N·m (9 ± 2 lb ft) 的扭矩。
- 连接线束组件 (3) 。
- 安装护罩组件 (4) 。
- 安装管组件 (1) 。
Caterpillar Information System:
EMCPII+ for Gas Engines GSC CID 0190 - FMI 03
2003/03/10 New Terminology is Now Used {7000}
EMCPII+ for Gas Engines GSC CID 0190 - FMI 02
C9 Marine Engines and C9 Marine Generator Sets Speed/Timing Sensor - Remove and Install
G3520C and G3520E Generator Set Engines Engine Oil and Water Pump Drive - Assemble
G3520C and G3520E Generator Set Engines Engine Oil and Water Pump Drive - Disassemble
C9 Marine Engines and C9 Marine Generator Sets Inlet Air Temperature Sensor - Remove and Install
C9 Marine Engines and C9 Marine Generator Sets Injection Actuation Pressure Sensor - Remove and Install
3516B HD Generator Set Refill Capacities
C9 Marine Engines and C9 Marine Generator Sets Fuel Temperature Sensor - Remove and Install
EMCPII+ for Gas Engines GSC CID 0168 - FMI 04
EMCPII+ for Gas Engines GSC CID 0168 - FMI 03
EMCPII+ for Gas Engines GSC CID 0269 - FMI 03
C7 Urban Transit Bus Engines Caterpillar Driver Information Display - Messenger
3054E Industrial Engine Balancer Group - Install - If Equipped
G3500B Engines Engine Oil Lines - Turbocharger Oil Lines
G3500B Engines Exhaust Manifold
EMCPII+ for Gas Engines GSC CID 0269 - FMI 04
G3520C and G3520E Generator Set Engines Engine Oil Pump - Remove
G3520C and G3520E Generator Set Engines Engine Oil Pump - Install
3516B HD Generator Set Generator Operation
2003/03/01 A New Crankshaft Seal Is Available {1160, 1202}
3500B Locomotive Engines Plate Locations and Film Locations
EMCPII+ for Gas Engines GSC CID 0442 - FMI 12