Engine Oil Pump - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7573     | 连杆支架     | 1     |
- 将工具 (A) 和适当的起吊设备连接到发动机机油泵 (12) 上。
Show/hide table
图 1 | g00990338 |
- 定位发动机机油泵 (12) 。 发动机机油泵的重量约为 36 kg (80 lb)。
- 安装螺栓 (15) 。
- 将套环 (14) 定位于发动机机油泵 (12) 上。
Show/hide table
图 2 | g00990337 |
- 安装螺栓 (13) 。
- 将 O 形密封圈定位于发动机机油泵 (12) 和弯头 (11) 上。
Show/hide table
图 3 | g00990336 |
- 安装螺栓 (10) 。
- 在管帽 (8) 上定位管组件 (9) 。
Show/hide table
图 4 | g00990334 |
- 定位适配器 (7) 。
- 安装螺栓 (6) 。
- 定位支架 (5) 。 安装螺栓 (4) 。
Show/hide table
图 5 | g00990333 |
- 定位密封垫和接头 (3) 。
- 安装螺栓 (1) 和螺栓 (2) 。
- 加注冷却液系统。 请参阅操作和保养手册, "加注容量和建议"。
Caterpillar Information System:
G3520C and G3520E Generator Set Engines Engine Oil Pump - Remove
EMCPII+ for Gas Engines GSC CID 0269 - FMI 04
G3500B Engines Exhaust Manifold
G3500B Engines Engine Oil Lines - Turbocharger Oil Lines
3054E Industrial Engine Balancer Group - Install - If Equipped
C7 Urban Transit Bus Engines Caterpillar Driver Information Display - Messenger
EMCPII+ for Gas Engines GSC CID 0269 - FMI 03
G3520C and G3520E Generator Set Engines Exhaust Elbow - Remove and Install
EMCPII+ for Gas Engines GSC CID 0190 - FMI 03
2003/03/10 New Terminology is Now Used {7000}
EMCPII+ for Gas Engines GSC CID 0190 - FMI 02
C9 Marine Engines and C9 Marine Generator Sets Speed/Timing Sensor - Remove and Install
3516B HD Generator Set Generator Operation
2003/03/01 A New Crankshaft Seal Is Available {1160, 1202}
3500B Locomotive Engines Plate Locations and Film Locations
EMCPII+ for Gas Engines GSC CID 0442 - FMI 12
EMCPII+ for Gas Engines GSC CID 0443 - FMI 12
2003/03/01 Identifying the Correct Crankshaft Gear {1204}
C9 Marine Engines and C9 Marine Generator Sets Air Cleaner Housing - Remove and Install
EMCPII+ for Gas Engines GSC CID 0590 - FMI 09
EMCPII+ for Gas Engines GSC CID 0770 - FMI 09
G3500B Engines Engine Oil Lines
G3520B Engines +5V Sensor Voltage Supply
EMCPII+ for Gas Engines Indicator for Emergency Stop