Engine Oil and Water Pump Drive - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-0520     | 冲头总成     | 1     |
- 降低轴承 (10) 温度。
Show/hide table
图 1 | g00994070 |
- 使用工具 (A) ,将轴承 (10) 安装到适配器组件 (4) 中。 轴承中的机油孔必须与适配器组件中的孔对齐。 轴承不得突出适配器组件上部。 组装后,轴承内径应达到 75.000 ± 0.055 mm (2.9527 ± 0.0022 in)。
- 将 O 形密封圈 (11) 安装到适配器组件 (4) 上。
- 将齿轮 (9) 安装在轴组件 (6) 上。
Show/hide table
图 2 | g00994066 |
- 安装螺栓 (8) 。
- 将适配器组件 (4) 安装到轴组件 (6) 上。
Show/hide table
图 3 | g00994065 |
- 将止推垫圈 (7) 定位在适配器组件 (4) 上
- 安装螺栓 (5) 。
- 冷却轴承 (1) 。
Show/hide table
图 4 | g00994064 |
- 使用工具 (A) ,将轴承 (1) 安装在适配器组件 (2) 中。 在组装后,轴承内径应达到 75.000 ± 0.055 mm (2.9527 ± 0.0022 in)。
- 将 O 形密封圈 (3) 安装在适配器组件 (2) 上。
End By: 安装发动机机油和水泵驱动器。 参考 拆解与组装, "发动机机油和水泵驱动器 - 安装"。
Caterpillar Information System:
G3520C and G3520E Generator Set Engines Engine Oil and Water Pump Drive - Disassemble
C9 Marine Engines and C9 Marine Generator Sets Inlet Air Temperature Sensor - Remove and Install
C9 Marine Engines and C9 Marine Generator Sets Injection Actuation Pressure Sensor - Remove and Install
3516B HD Generator Set Refill Capacities
C9 Marine Engines and C9 Marine Generator Sets Fuel Temperature Sensor - Remove and Install
EMCPII+ for Gas Engines GSC CID 0168 - FMI 04
EMCPII+ for Gas Engines GSC CID 0168 - FMI 03
G3520C and G3520E Generator Set Engines Engine Oil and Water Pump Drive - Install
G3520C and G3520E Generator Set Engines Engine Oil and Water Pump Drive - Remove
C9 Marine Engines and C9 Marine Generator Sets Fuel Pressure Sensor - Remove and Install
C11, C13, and C15 On-highway Engines Diagnostic Flash Code Retrieval
C11, C13 and C15 On-highway Engines 0284-06 Engine Coolant Diverter current high (98)
C9 Marine Engines and C9 Marine Generator Sets Speed/Timing Sensor - Remove and Install
EMCPII+ for Gas Engines GSC CID 0190 - FMI 02
2003/03/10 New Terminology is Now Used {7000}
EMCPII+ for Gas Engines GSC CID 0190 - FMI 03
G3520C and G3520E Generator Set Engines Exhaust Elbow - Remove and Install
EMCPII+ for Gas Engines GSC CID 0269 - FMI 03
C7 Urban Transit Bus Engines Caterpillar Driver Information Display - Messenger
3054E Industrial Engine Balancer Group - Install - If Equipped
G3500B Engines Engine Oil Lines - Turbocharger Oil Lines
G3500B Engines Exhaust Manifold
EMCPII+ for Gas Engines GSC CID 0269 - FMI 04
G3520C and G3520E Generator Set Engines Engine Oil Pump - Remove