Engine Oil Cooler - Remove
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Drain the coolant from the engine oil cooler into a suitable container. Drain the engine oil from the engine oil cooler into a suitable container. Refer to Operation and Maintenance Manual for the procedure on draining the engine coolant and the engine oil.
Show/hide table
Illustration 1 g00940966 - Remove bolts (11).
- Disconnect hose assemblies (8) and (9) from adapter (13). Remove gaskets (12).
- Remove nuts (10) and flanges (6).
- Remove hose assemblies (8) and (9). Remove seals (5).
- Remove bolts (7).
- Remove engine oil cooler housing (4) and gasket (3) from the cylinder block.
- Remove engine oil cooler (1) and seals (2) from engine oil cooler housing (4).
Caterpillar Information System:
CIPI UNDERCARRIAGE Arrangements: 9Q-5240, 9Q-5241, 9Q-5242, 9Q-5250, 9Q-5253, 9Q-5265, 9Q-5266, 9Q-5392, 9Q-5393, 9Q-5478, 9Q-5504, 9Q-5621, 9Q-5643, 9Q-5651, 9Q-5709, 9Q-5718, 9Q-5723, 9Q-5724, 9Q-5725, 9Q-5726, 9Q-5731, 9Q-5747, 9Q-5780, 9Q-5792, 9 Recoil Spring
2003/01/01 A New Drain Valve Group is Available to Drain Condensate from the Air Plenum {1094, 1372}
CIPI UNDERCARRIAGE Arrangements: 166-7047, 177-3011, 177-3553, 177-4279, 200-2995, 200-4060, 204-0808, 212-6225, 213-8653, 215-7227, 218-2237, 231-5143, 3Q-6638, 3Q-6641, 6Z-7749, 6Z-7751, 6Z-7857, 6Z-7890, 6Z-7926, 6Z-7938, 6Z-7992, 9Q-5034, 9Q-5042 Front Idler
3126B Marine Engines CID 0102 FMI 04 Boost Pressure Sensor short to ground
C7 Petroleum Engines Basic Engine
C11, C13 and C15 On-highway Engines Injector Code - Calibrate
3126B Marine Engines CID 0102 FMI 03 Boost Pressure Sensor short to +batt
3056E Industrial Engine Water Pump - Remove and Install
C7 Petroleum Engines Air Inlet and Exhaust System
C15 On-highway Engine Fuel Filter Lines
G3500B Engines Water Temperature Regulator
3500B Engines Thermostatic Valve
3056E Industrial Engine Engine Oil Cooler - Install
C27 and C32 Generator Set Engines Valve Mechanism
C7 On-highway Engine Exhaust Manifold
2003/03/01 New Valve Group and Coil Now Used {3139}
G3520C and G3520E Generator Set Engines Circuit Breaker
2003/02/24 A Revised Special Instruction Provides Information on Service Replacement of the Turbocharger (for Turbocharged Engines Only) {1052}
G3520C and G3520E Generator Set Engines Air/Fuel Ratio Control - Adjust
C7 and C9 On-Highway Engines Exhaust Brake Parameters
C15 On-highway Engine Valve Mechanism Cover
3056E Industrial Engine Engine Oil Filter Base - Remove and Install
C15 Petroleum Generator Set Engines Electronic Unit Injector Wiring
C7 and C9 On-Highway Engines Engine Monitoring Parameters