90° Elbows On Quick Disconnect Couplers Make Installation Easier{0690}
Usage:
Two 90° elbows are available for use with quick disconnect couplers. These elbows can be an advantage if the location of the nipple causes you to reach a long distance or if there is very little clearance for the installation of the coupler. These locations make installation of the coupler a one-handed operation. You must pull back on the sleeve while you push the coupler over the nipple. This is difficult when a hose is connected directly to the end of the coupler. With a 90° elbow installed between the coupler and the hose, you can pull back the sleeve with your fingers while the coupler is pushed onto the nipple with the palm of your hand.
Caterpillar Information System:
1979/04/16 Longer Self-Locking Bolts Now Used To Hold The Parking Brake Group To The Bearing Retainer{3161,3275,4267}
1979/04/16 How To Extend The Service Life Of 1P5550 Fuel Cam Locking Tool Assembly{0654,1250}
1979/04/16 Hydraulic Accumulator Now Used In Lines Group For Draft Frame{5077,5057,5314,5055}
1979/04/16 Clean The Orifice In The Pressure Control Group During A Transmission Overhaul{3167}
1979/04/16 Testing And Adjusting Procedure For 5P4210 Modular Cab Tilting Cylinder And Valve{0620}
1979/04/09 New Fan Motors Used In Cab Pressurizers{7311}
1979/04/09 Separate Scraper Batteries And Electronic Transmission Controls Now Used{1400,3168}
1979/04/09 New Exhaust Valve Has Improved Three-Piece Construction{1105}
1979/04/09 Improved Engine Design Uses Cylinder Block With Spacer Plate{1000}
1979/04/09 New Brake Actuators And Improved Air System Give Better Brake Operation{4250}
1979/04/09 Serial Numbers Used Instead Of Test Numbers On Power Shift Transmissions{3150,7557}
1979/04/09 Stronger Components Used In Cushion Hitch Group{7107}
1979/04/16 New Flywheel Clutch Uses Three Driven Discs Instead Of Two; Must Be Used Only With New Flywheel{3052,3054,1156}
1979/04/16 Different Type Brake Lining In Steering Brake Group; Higher Oil Level Used With New Lining{4110,3004}
1979/04/23 Two Bolts Have Been Added At The Junction Of The Converter And Retarder Housing To Prevent O-Ring Seal Damage{3109}
1979/04/23 New Retainer Used Between Bolt And Gear In The Torque Converter{3101}
1979/04/23 Dampeners Added To Steering Brake Group To Prevent Noise From Vibration Of Brake Band Assembly{4110}
1979/04/23 Careful, Correct Installation And Maintenance Of Fuel Injection Lines Is Very Important To Prevent Possible Engine Damage, Fire And Other Problems{1252}
1979/04/23 New Oil Cooler Bonnets Used On 3408 And 3412 Engines{1378,1354,1380}
1979/04/23 New Retaining Rings Used In Planetary Groups For Power Shift Transmissions{3176,3150}
1979/04/23 Dowtherm Test Strips No Longer Available{0651,1350}
1979/04/23 Reinforcement Of Draft Frame Gooseneck To Prevent Cracks{6220,6209,6207}
1979/04/23 New Metering Pump In Steering System Has Improved Internal (Inside) Seals{4306}
1979/04/30 The 6B5067 Race And Roller Assembly, Used In Final Drive Group, Can Be Either Of Two Designs{4050,4091}