Mounting Bracket - Remove and Install
- Remove the work tool from the host machine. Refer to Operation and Maintenance Manual, "Work Tool Installation and Removal".
Show/hide table
Illustration 1 g06255959 Typical example - Position work tool (1) in the upright position, when possible. Only position the work tool on a solid, level surface. Refer to the above illustration. If a solid, level surface is not available, then position the work tool on one side.
Show/hide table
Illustration 2 g06255960 Typical example - Attach a suitable lifting device to mounting bracket (3). The weight of mounting bracket (3) is approximately
255 kg (562 lb) . - Remove bolts (2) and mounting bracket (3) from work tool.
- Install mounting bracket (3) in the reverse order of removal.
- Tighten bolts (2) to a torque of
900 ± 100 N·m (664 ± 74 lb ft) .
- Tighten bolts (2) to a torque of
Caterpillar Information System:
Installation of the 494-9529 Front Lines Gp on Certain Hydraulic Excavators {5057} Installation of the 494-9529 Front Lines Gp on Certain Hydraulic Excavators {5057}
730, 730 Ejector, 735, 740 Ejector, and 745 Articulated Trucks Information Display Display Features
320D2 FM Forestry Machine Engine Supplement Turbocharger - Remove and Install
Procedure to Troubleshoot the Transmission Speed Sensor on Certain Material Handlers, Mobile Hydraulic Power Units, and Wheeled Excavators {3030} Procedure to Troubleshoot the Transmission Speed Sensor on Certain Material Handlers, Mobile Hydraulic Power Units, and Wheeled Excavators {3030}
320D2 FM Forestry Machine Engine Supplement Muffler - Remove and Install
A New Warning Film Is Now Available for the Material Handling Arms {6542, 7405} A New Warning Film Is Now Available for the Material Handling Arms {6542, 7405}
336 and 336 GC Excavator Equipment Lowering with Engine Stopped
340 Excavator Engine and Machine Warm-Up
PM820, PM822, and PM825 Cold Planer Machine Systems Flow Control Valve - Remove and Install - Front
320E, 323F and 336F XE Excavators Supplement for Cat Grade Control with Assist Electronic Control (Machine System)
Next Generation Hydraulic Excavator Monitoring System General Information
PM820, PM822, and PM825 Cold Planer Machine Systems Rotor Drive Motor (Auxiliary) - Remove and Install
G315B and G320B Waste Handling Grapple Hydraulic Cylinder - Remove and Install
G315B and G320B Waste Handling Grapple Grapple Housing and Shell Gp - Disassemble
G315B and G320B Waste Handling Grapple Grapple Housing and Shell Gp - Assemble
730, 730 Ejector, 735, 740 Ejector, and 745 Articulated Trucks Information Display Display Navigation
S2050, S3050, S2070, S3070, S2090 and S3090 Shears General Information - Rotating Shear
A Ground Wiring Addition Is Now Used for the ARD Nozzle Heater Relay on Certain C9.3 through C18 Tier 4 Machine Engines {1050, 108D, 1422, 4493} A Ground Wiring Addition Is Now Used for the ARD Nozzle Heater Relay on Certain C9.3 through C18 Tier 4 Machine Engines {1050, 108D, 1422, 4493}
Bluetooth Operator ID and Machine Security System (MSS) General Information
336 and 336 GC Excavator Stopping the Engine
320D2 FM Forestry Machine Engine Supplement Water Temperature Regulator - Remove and Install
320D2 FM Forestry Machine Engine Supplement Water Pump - Remove and Install
730, 730 Ejector, 735, 740 Ejector, and 745 Articulated Trucks Information Display Menu Navigation
Improved Handrail Assembly Is Now Used on Certain Excavators and Forest Machines Fitted with A Rear Entry Cab {7260} Improved Handrail Assembly Is Now Used on Certain Excavators and Forest Machines Fitted with A Rear Entry Cab {7260}