Turbocharger - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Loctite C5A Copper Anti-Seize | - |
Start By:
- Release the system pressure.
- Open the hood.
Show/hide table
Illustration 1 g06209217 - Remove heat shield (1) and loosen clamp (2).
- Loosen clamp (4) and disconnect hose (3).
Show/hide table
Illustration 2 g06209544 - Remove bolt (5), disconnect the tube assembly, and remove the gasket (not shown).
- Loosen clamps (6) and remove tube (7).
Show/hide table
Illustration 3 g06209549 - Remove bolts (8) and plate assembly (9).
Show/hide table
Illustration 4 g06209565 - Remove bolts (10), disconnect hose assembly (12), and remove gasket (11) (not shown).
- Loosen clamp (13) and disconnect hose (14).
Show/hide table
Illustration 5 g06209583 Typical Example - Remove nuts (15), gasket (16), and turbocharger (17).
- Install turbocharger (17) in the reverse order of removal.
- Apply Tooling (A) to nuts (15).
- Tighten nuts (15) to a torque of
44 N·m (32 lb ft) . - Tighten bolts (10) to a torque of
22 N·m (195 lb in) . - Tighten bolt (5) to a torque of
20 N·m (177 lb in) .
Caterpillar Information System:
Procedure to Troubleshoot the Transmission Speed Sensor on Certain Material Handlers, Mobile Hydraulic Power Units, and Wheeled Excavators {3030} Procedure to Troubleshoot the Transmission Speed Sensor on Certain Material Handlers, Mobile Hydraulic Power Units, and Wheeled Excavators {3030}
320D2 FM Forestry Machine Engine Supplement Muffler - Remove and Install
A New Warning Film Is Now Available for the Material Handling Arms {6542, 7405} A New Warning Film Is Now Available for the Material Handling Arms {6542, 7405}
336 and 336 GC Excavator Equipment Lowering with Engine Stopped
340 Excavator Engine and Machine Warm-Up
PM820, PM822, and PM825 Cold Planer Machine Systems Flow Control Valve - Remove and Install - Front
320E, 323F and 336F XE Excavators Supplement for Cat Grade Control with Assist Electronic Control (Machine System)
Next Generation Hydraulic Excavator Monitoring System General Information
PM820, PM822, and PM825 Cold Planer Machine Systems Rotor Drive Motor (Auxiliary) - Remove and Install
Control Lever Assembly May Break in the Main Hydraulic Pump Group on Certain 374F Excavators and Mobile Hydraulic Power Units {5070} Control Lever Assembly May Break in the Main Hydraulic Pump Group on Certain 374F Excavators and Mobile Hydraulic Power Units {5070}
336 and 336 GC Excavator Fuel Tank Shutoff and Drain Control
New Gussets in the Undercarriage Are Now Available for Certain Forestry Excavators Equipped with A Grapple Saw {4151} New Gussets in the Undercarriage Are Now Available for Certain Forestry Excavators Equipped with A Grapple Saw {4151}
730, 730 Ejector, 735, 740 Ejector, and 745 Articulated Trucks Information Display Display Features
Installation of the 494-9529 Front Lines Gp on Certain Hydraulic Excavators {5057} Installation of the 494-9529 Front Lines Gp on Certain Hydraulic Excavators {5057}
G315B and G320B Waste Handling Grapple Mounting Bracket - Remove and Install
G315B and G320B Waste Handling Grapple Hydraulic Cylinder - Remove and Install
G315B and G320B Waste Handling Grapple Grapple Housing and Shell Gp - Disassemble
G315B and G320B Waste Handling Grapple Grapple Housing and Shell Gp - Assemble
730, 730 Ejector, 735, 740 Ejector, and 745 Articulated Trucks Information Display Display Navigation
S2050, S3050, S2070, S3070, S2090 and S3090 Shears General Information - Rotating Shear
A Ground Wiring Addition Is Now Used for the ARD Nozzle Heater Relay on Certain C9.3 through C18 Tier 4 Machine Engines {1050, 108D, 1422, 4493} A Ground Wiring Addition Is Now Used for the ARD Nozzle Heater Relay on Certain C9.3 through C18 Tier 4 Machine Engines {1050, 108D, 1422, 4493}
Bluetooth Operator ID and Machine Security System (MSS) General Information
336 and 336 GC Excavator Stopping the Engine
320D2 FM Forestry Machine Engine Supplement Water Temperature Regulator - Remove and Install