Water Temperature Regulators - Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 1P-0510 | Driver Group | 1 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Inspect all gaskets and seals. Replace as necessary. |
- Use Tooling (A) to install seals (10), if necessary. Ensure that the lip of the seal is toward the insideof the housing.
Show/hide table
Illustration 2 g06132177 Show/hide tableNOTICE If the water temperature regulator is installed incorrectly, it will cause the engine to overheat.
- Install four water temperature regulators (9) with the spring upward.
Show/hide table
Illustration 3 g06132172 - Install seals (8).
Show/hide table
Illustration 4 g06132163 - Install seal carrier (7).
Show/hide table
Illustration 5 g06132154 - Position the water regulator housing and install 5 bolts (2).
- Install 4 bolts (1) and (6).
- Position hose and install 2 bolts (5) in flange and two bolts (4) in clamp.
- Install hose and coupling (3).
- Fill the cooling with coolant to the correct level. Refer to the Operation and Maintenance Manual for the correct procedure.
Show/hide table
| |
| Illustration 1 | g06132207 |
Caterpillar Information System:
Installation Procedure for the Material Handling Slip-On Buckets on Certain Logging Forks {0679, 6001, 6101, 6103, 6104, 6113, 6114, 6123, 6405} Installation Procedure for the Material Handling Slip-On Buckets on Certain Logging Forks {0679, 6001, 6101, 6103, 6104, 6113, 6114, 6123, 6405}
313D2 Excavator Machine Systems Tank and Filter (Hydraulic) - Install
313D2 Excavator Machine Systems Tank and Filter (Hydraulic) - Remove
318D2 Excavator Machine Systems Hydraulic Tank and Filter - Install
318D2 Excavator Machine Systems Hydraulic Tank and Filter - Remove
M325D MH Material Handler Axle Oil Sample - Obtain
308E2 CR Mini Hydraulic Excavator Variable Angle Boom (VAB) Machine Systems Track - Connect
G3512 Generator Set Engine Water Temperature Regulators - Remove
320D3 and 323D3 Excavators Machine System Specifications Bucket Cylinder
329F and 330F Excavators Warning Categories
329F and 330F Excavators Symbols
422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Air Cleaner Dust Valve - Clean/Inspect
G3500H Generator Set Engine Data Link - Test
308E2 CR Mini Hydraulic Excavator Variable Angle Boom (VAB) Machine Systems Track Carrier Roller - Remove and Install
326D2 and 330D2 Excavator Machine System Electronic Control Module
G3500H Generator Set Engine Detonation - Test
730C2 and 725C2 Articulated Truck Power Train Rear Axle - Remove and Install
352F Mobile Hydraulic Power Unit (MHPU) Machine System Hood
308E2 CR Mini Hydraulic Excavator Variable Angle Boom (VAB) Machine Systems Front Idler and Recoil Spring - Install
G3512 Generator Set Engine Water Pump - Install
320D2 and 323D2 Excavators Hydraulic System Main Control Valve
PM820, PM822, and PM825 Cold Planer Machine Systems Access Door - Remove and Install - Rotor Chamber
PM310, PM312, and PM313 Cold Planer Stopping the Engine
336F and 340F Excavators CAN Data Link - Test