Combined Function - Electric Control: Default Value of Work Tool Parameters
Note: For this system, parameters that are not shown in the tables do not affect operation of the work tool.
Note: The parameters in the "DARK GRAY" cells are not displayed in the monitor and do not affect the operation of the work tool.
Table 1 shows some of the approved Caterpillar work tools that are used.
Table 2 shows parameters for "TOOL#1" through "TOOL#5".
Table 3 shows parameters for "TOOL#6" through "TOOL#10".
Note: Refer to the specific machine model for additional parameters.
Note: Parameters that are not common to all machines are listed with the appropriate machine.
Show/hide table
| SYSTEM 23 | ||
| Work Tool | Direction of Flow | System 23 "TOOL#s" |
| "Compactor" | 1 Way | "TOOL#1" |
| "Shear" | 2 Way | "TOOL#2", "TOOL#4" |
| "Hammer" | 1 Way | "TOOL#3" |
| "Thumb" | 2 Way | "TOOL#5" |
Show/hide table
| Name | Display | "TOOL#1" | "TOOL#2" | "TOOL#3" | "TOOL#4" | "TOOL#5" |
|---|---|---|---|---|---|---|
| "TOOL PROGRAM -> GENERAL" | ||||||
| Tool Program Tool Type | "Tool Type" | Compactor | Shear | Hammer | Shear | Bucket Thumb |
| Name of the tool | "Tool Program Name" | CVP110 | MP15 | H120 | MP20 | THUMB 1P |
| Maximum position of the dial for the throttle | "Max Throttle Dial Position" | 10 | 10 | 10 | 10 | 10 |
| Minimum position of the dial for the throttle | "Min Throttle Dial Position" | 1 | 1 | 1 | 1 | 1 |
| Economy Mode Enable Status | "Eco Mode Enable Status" | ENABLED | ENABLED | ENABLED | ENABLED | ENABLED |
| Combiner for two pump flow | "2 Pump Flow Combine" | ENABLED | ENABLED | ENABLED | ENABLED | DISABLED |
| Initial power reduction of the main pump | "Init Med Circuit Torque Red" | 0% | 0% | 0% | 0% | 0% |
| Total power reduction of the main pump | "Total Med Circuit Trq Red" | 50% | 50% | 50% | 50% | 50% |
| One-way flow or two-way flow | "1Way/ 2Way Valve Mode" | ONE-WAY | TWO-WAY | ONE-WAY | TWO-WAY | TWO-WAY |
| Pressure of the number 1 variable relief valve | "Variable Rel Valve #1 Pres" | |
|
|
|
|
| Pressure of the number 2 variable relief valve | "Variable Rel Valve #2 Press" | |
|
|
|
|
| Temperature of the high temperature warning for the hydraulic oil | "Overheat Event Threshold" | |
|
|
|
|
| "TOOL PROGRAM -> ATTACHMENT #1 VALVE" | ||||||
| Flow settings of the number 1 attachment valve | "Atch #1 Flow Setting" | |
|
|
|
|
| Additional flow for the number 1 attachment valve during multiple operation | "Atch #1 Multi-Ope Add Flow" | |
|
|
|
|
| Maximum pressure for the extension of the number 1 attachment valve | "Atch #1 Max Ext Press" | |
|
|
|
|
| Maximum pressure for the retraction of the number 1 attachment valve | "Atch #1 Max Ret Press" | |
|
|
|
|
| Maximum pilot pressure for the extension of attachment valve during multiple operations | Atch #1 M-Ope Max Ext | |
|
|
|
|
| Maximum pilot pressure for the retraction of attachment valve during multiple operations | Atch #1 M-Ope Max Ret | |
|
|
|
|
| Open time of the number 1 attachment valve | "Atch #1 Open Time" | 0.20 seconds | 0.20 seconds | 0.20 seconds | 0.20 seconds | 0.20 seconds |
| Close time of the number 1 attachment valve | Atch #1 Close Time | 0.20 seconds | 0.20 seconds | 0.20 seconds | 0.20 seconds | 0.20 seconds |
| Direction of the oil flow for the number 1 attachment valve | "Atch #1 Tool Flow Direction" | Normal | Normal | Normal | Normal | Normal |
| "TOOL PROGRAM -> ATTACHMENT #3 VALVE"(1) | ||||||
| Flow settings of the number 3 attachment valve | "Atch #3 Flow Settin" | |
|
|
|
|
| Additional flow for the number 3 attachment valve during multiple operation | "Atch #3 Multi-Ope Add Flow" | |
|
|
|
|
| Maximum pressure for the extension of the number 3 attachment valve | "Atch #3 Max Ext Press" | |
|
|
|
|
| Maximum pressure for the retraction of the number 3 attachment valve | "Atch #3 Max Ret Press" | |
|
|
|
|
| Open time of the number 3 attachment valve | "Atch #3 Open Time" | 0.20 seconds | 0.20 seconds | 0.20 seconds | 0.20 seconds | 0.20 seconds |
| Close time of the number 3 attachment valve | "Atch #3 Close Time" | 0.20 seconds | 0.20 seconds | 0.20 seconds | 0.20 seconds | 0.20 seconds |
| Direction of the oil flow for the number 3 attachment valve | "Atch #3 Tool Flow Direction" | Normal | Normal | Normal | Normal | Normal |
Show/hide table
| (1) | If equipped with medium pressure |
Show/hide table
| Name | Display | "TOOL#6" | "TOOL#7" | "TOOL#8" | "TOOL#9" | "TOOL#10" |
|---|---|---|---|---|---|---|
| "TOOL PROGRAM -> GENERAL" | ||||||
| Tool Program Tool Type | "Tool Type" | Other | Other | Other | Other | Other |
| Name of the tool | "Tool Program Name" | 0 | 0 | 0 | 0 | 0 |
| Maximum position of the dial for the throttle | "Max Throttle Dial Position" | 10 | 10 | 10 | 10 | 10 |
| Minimum position of the dial for the throttle | "Min Throttle Dial Position" | 1 | 1 | 1 | 1 | 1 |
| Economy Mode Enable Status | "Eco Mode Enable Status" | ENABLED | ENABLED | ENABLED | ENABLED | ENABLED |
| Combiner for two pump flow | "2 Pump Flow Combine" | DISABLED | DISABLED | DISABLED | DISABLED | DISABLED |
| Initial power reduction of the main pump | "Init Med Circuit Torque Red" | 0% | 0% | 0% | 0% | 0% |
| Total power reduction of the main pump | "Total Med Circuit Trq Red" | 50% | 50% | 50% | 50% | 50% |
| One-way flow or two-way flow | "1Way/ 2Way Valve Mode" | "TWO-WAY" | "TWO-WAY" | "TWO-WAY" | "TWO-WAY" | "TWO-WAY" |
| Pressure of the number 1 variable relief valve | "Variable Rel Valve #1 Pres" | |
|
|
|
|
| Pressure of the number 2 variable relief valve | "Variable Rel Valve #2 Press" | |
|
|
|
|
| Temperature of the high temperature warning for the hydraulic oil | "Overheat Event Threshold" | |
|
|
|
|
| "TOOL PROGRAM -> ATTACHMENT #1 VALVE" | ||||||
| Flow settings of the number 1 attachment valve | "Atch #1 Flow Setting" | |
|
|
|
|
| Additional flow for the number 1 attachment valve during multiple operation | "Atch #1 Multi-Ope Add Flow" | |
|
|
0 |
0 |
| Maximum pressure for the extension of the number 1 attachment valve | "Atch #1 Max Ext Press" | |
|
|
|
|
| Maximum pressure for the retraction of the number 1 attachment valve | "Atch #1 Max Ret Press" | |
|
|
|
|
| Maximum pilot pressure for the extension of attachment valve during multiple operations | Atch #1 M-Ope Max Ext | |
|
|
|
|
| Maximum pilot pressure for the retraction of the attachment valve during multiple operations | Atch #1 M-Ope Max Ret | |
|
|
|
|
| Open time of the number 1 attachment valve | "Atch #1 Open Time" | 0.20 seconds | 0.20 seconds | 0.20 seconds | 0.20 seconds | 0.20 seconds |
| Close time of the number 1 attachment valve | "Atch #1 Close Time" | 0.20 seconds | 0.20 seconds | 0.20 seconds | 0.20 seconds | 0.20 seconds |
| Direction of the oil flow for the number 1 attachment valve | "Atch #1 Tool Flow Direction" | Normal | Normal | Normal | Normal | Normal |
| "TOOL PROGRAM -> ATTACHMENT #3 VALVE"(1) | ||||||
| Flow settings of the number 3 attachment valve | "Atch #3 Flow Settin" | |
|
|
|
|
| Additional flow for the number 3 attachment valve during multiple operation | "Atch #3 Multi-Ope Add Flow" | |
|
|
|
|
| Maximum pressure for the extension of the number 3 attachment valve | "Atch #3 Max Ext Press" | |
|
|
|
|
| Maximum pressure for the retraction of the number 3 attachment valve | "Atch #3 Max Ret Press" | |
|
|
|
|
| Open time of the number 3 attachment valve | "Atch #3 Open Time" | 0.20 seconds | 0.20 seconds | 0.20 seconds | 0.20 seconds | 0.20 seconds |
| Close time of the number 3 attachment valve | "Atch #3 Close Time" | 0.20 seconds | 0.20 seconds | 0.20 seconds | 0.20 seconds | 0.20 seconds |
| Direction of the oil flow for the number 3 attachment valve | "Atch #3 Tool Flow Direction" | Normal | Normal | Normal | Normal | Normal |
Show/hide table
| (1) | If equipped with medium pressure |
Caterpillar Information System:
2013/12/10 A New Exhaust Manifold is Now Used on Certain 303E CR Mini Hydraulic Excavators {1062}
312F GC and 313F GC Excavators Tool Control System Work Tool - Select
311F Excavators Tool Control System Work Tool Parameter - Program
302.7D CR Mini Hydraulic Excavator Basic Engine
300.9D Mini Hydraulic Excavator Cylinder Speed - Check
2014/01/06 Positive Pin Retention 2 (PPR2) Track Link Assemblies are Now Used on Certain 324D Forest Machines {4169, 4171}
302.7D CR Mini Hydraulic Excavator Cylinder Drift - Check
2014/04/24 A New Engine Front Crankshaft Seal Is Now Used On Certain Machine Applications Equipped With C13 Engines {1160}
2013/12/11 New Caps are Now Used on the Counterweight of Certain 314E Excavators {7056}
311F Excavators Tool Control System Process for Setting Up the Work Tool
Installation Procedure for the 448-1172 Coupler Control Ar {1408, 5057, 7301, 7405, 7557} Installation Procedure for the 448-1172 Coupler Control Ar {1408, 5057, 7301, 7405, 7557}
311F Excavators Tool Control System General Information
C27 Engines for Caterpillar Built Machines Muffler and Converter - Remove and Install
311F Excavators Tool Control System Combined Function - Electric Control: Parameter Setting
336F and 340F Excavators Tool Control System One-Way/One or Two Pump - Electric Control
C9.3 Tier 4 Final Engines Fuel Filter Base
Procedure to Install Heated and Insulated Fumes Disposal Hoses and Open Crankcase Ventilation (OCV) Canister Components on Certain 349 Excavators{1074} Procedure to Install Heated and Insulated Fumes Disposal Hoses and Open Crankcase Ventilation (OCV) Canister Components on Certain 349 Excavators{1074}
349E Excavator Hydraulic System Negative Flow Control System
374F Excavator Machine Systems Main Control Valve - Disassemble - Bucket and Boom
349E Excavator Hydraulic System Boom Hydraulic System
Installation Procedure for the 452-7116 Front Lines Gp on Certain Hydraulic Excavators{5057} Installation Procedure for the 452-7116 Front Lines Gp on Certain Hydraulic Excavators{5057}
311F Excavator Machine Systems Pump Control (Negative Flow) - Adjust
300.9D Mini Hydraulic Excavator Fuel Injection Timing - Check/Adjust
Procedure to Upgrade EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.3{4490} Procedure to Upgrade EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.3{4490}