Turbocharger - Assemble
组装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 9S-6363     | 涡轮增压器夹具     | 1     |
B     | 9S-6343     | 夹具组件     | 1     |
E     | FT-0745     | 改装钳     | 1     |
F     | 8T-5096     | 千分表     | 1     |
G     | 5N-5561     | 硅脂     | -     |
H     | 4C-5593     | 螺纹润滑剂     | -     |
I     | 5P-3931     | 防粘结剂     | -     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保涡轮增压器芯壳体中的所有油道清洁,没有污垢和异物。
Show/hide table
图 1 | g01424862 |
- 将清洁的发动机机油涂在芯组件的所有零件上。
- 将垫圈 (23) 和轴承 (22) 安装到芯壳体 (25) 中。 确保轴承 (2) 上的识别标记朝上。
- 用工具 (E) 将扣环 (21) 和 (24) 安装到芯壳体 (25) 中。
- 将上轴承 (20) 和垫圈安装到芯壳体中。 确保识别标记朝上。
Show/hide table
图 2 | g01424860 |
- 将 O 形密封圈和止推轴承 (19) 安装到芯壳体中。
- 将套环 (18) 安装在背板组件 (17) 另一侧。
Show/hide table
图 3 | g01424859 |
Show/hide table
图 4 | g01424857 |
- 将密封圈安装到隔套 (15) 中。 将隔套 (15) 安装到背板组件 (17) 中。 将背板组件 (17) 安装到芯壳体上。
- 定位锁 (16) 并安装螺栓 (14) 。 拧紧螺栓 (14) 并弯曲锁 (16) 的凸舌。
- 将涡轮轴 (11) 安装在工具 (B) 中。 将密封圈 (12) 和护罩 (13) 安装到涡轮轴 (13) 上。
Show/hide table
图 5 | g01424852 |
注: 将工具 (G) 涂在密封圈 (12) 的槽中。
- 安装垫圈 (10) 和轴承 (9) ,使识别标记朝上。 向上。 安装止推垫圈 (8) ,使三个润滑槽朝上。 也将 O 形密封圈 (7) 安装到芯壳体中。
Show/hide table
图 6 | g01424825 |
- 安装将背板组件固定到位的锁和螺栓。 拧紧螺栓至扭矩为 10.2 ± 1.1 N·m (90 ± 10 lb in)。
Show/hide table
图 7 | g00593907 |
Show/hide table
注意 |
---|
确保涡轮轴 (6) 上的密封圈在芯壳体中正确就位。 |
- 采用以下步骤将叶轮安装到轴上。
- 将叶轮放到轴上。
- 将少量工具 (H) 涂在螺纹和将位于螺母下方的叶轮表面。
注: 当松开或拧紧螺母时,请勿弯曲轴或向其施加应力。
- 拧紧螺母至扭矩为 14.1 - 17.0 N·m (125 - 150 lb in)。
- 松开轴上的螺母。
- 拧紧螺母至扭矩为 3.5 N·m (31 lb in)。
- 将螺母多拧紧 120 度。
- 将芯壳体放在钳中。 用工具 (F) 检查轴端隙。 端隙必须为 0.08 至 0.25 mm (0.003 至 0.010'')。 如果轴端隙尺寸不正确,必须检查中央壳体的内部零件。
Show/hide table
图 8 | g00770104 |
- 将芯组件 (3) 放在涡轮壳体 (4) 中。 安装卡箍组件 (5) 。
Show/hide table
图 9 | g00593906 |
- 将涡轮壳体安装在工具 (A) 上。 将芯组件在涡轮壳体中放置到位。 确保壳体上的标记相互对齐。 将工具 (I) 涂在将芯组件固定到压缩机壳体 (1) 的卡箍 (2) 的螺纹上。 安装卡箍组件 (2) 后拧紧螺栓至扭矩为 14 ± 2 N·m (10 ± 2 lb ft)。
Show/hide table
图 10 | g00593902 |
End By: 安装涡轮增压器。 请参阅 拆解和组装, "涡轮增压器 - 安装"。
Caterpillar Information System:
Product Identification Numbers (PIN) Location Guide Excavator (Track)
SPS342 Skid Mounted Pumper Model View Illustrations
G3408C and G3412C Engines Turbocharger - Disassemble
G3500 Generator Sets Refill Capacities
3412C Engine Pistons and Connecting Rods - Assemble
3126B Engines for Caterpillar Built Machines Fuel Transfer Pump - Install - If Equipped
3500B Engines Turbocharger
3412E, C30 and C32 Marine Engines Camshaft - Install
3412E, C30 and C32 Marine Engines Camshaft - Remove
3126B Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove - If Equipped
3126B Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
3412C Engine Pistons and Connecting Rods - Disassemble
Product Identification Numbers (PIN) Location Guide Track-Type Tractor
3412C Engine Connecting Rod
2001/04/16 Correction to Operation and Maintenance Manual, SEBU7275-01, "Maintenance Interval Schedule" {7500}
G3408C and G3412C Engines Water Temperature Regulator - Remove
G3408C and G3412C Engines Water Temperature Regulator - Install
3412C Engine Connecting Rod Bearings - Install
G3408C and G3412C Engines Engine Oil Pan - Remove
G3408C and G3412C Engines Engine Oil Pan - Install
G3408C and G3412C Engines Water Pump - Remove
SPS342 Skid Mounted Pumper Product Description
G3408C and G3412C Engines Water Pump - Install
3126B Engines for Caterpillar Built Machines Lifter Group - Remove and Install