Exhaust Bypass - Disassemble
拆解步骤
开始:
- 卸下废气旁通。 请参阅拆解和装配, "废气旁通 - 拆卸"。
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下密封垫 (1) 。 检查密封垫的状况。 如果密封垫磨损或损坏，则用新零件更换。
Show/hide table
 | |
| 图 1 | g00784869 |
- 拆下呼吸器组件 (2) 。
- 均匀拆下螺栓 (3) 和垫圈。
注: 排气旁通有一个有张力的弹簧。 慢慢将每个螺栓转一圈，直到释放弹簧压力。
Show/hide table
 |
排气旁通阀盖处于弹簧压力下。 为防止人身伤害，小心拆卸此盖。 |
- 拆下盖 (4) 。
- 将弹簧 (5) 从盖 (4) 上拆下。
Show/hide table
 | |
| 图 2 | g00784889 |
- 将挡圈 (6) 从盖 (4) 上拆下。
Show/hide table
 | |
| 图 3 | g00784893 |
- 将螺栓 (7) 从盖 (4) 上拆下。
Show/hide table
 | |
| 图 4 | g00784897 |
- 将自锁紧螺母 (8) 和阀从底座组件 (9) 上拆下。
Show/hide table
 | |
| 图 5 | g00784901 |
- 拆下膜片挡圈 (10) 、膜片 (11) 和两个密封垫 (12) 。 底座组件 (9) 的膜片 (11) 每侧各有一个密封垫。
- 将挡板 (13) 从底座组件 (9) 上拆下。
Show/hide table
 | |
| 图 6 | g00784908 |
- 将垫圈 (14) 从底座组件 (9) 上拆下。
Show/hide table
 | |
| 图 7 | g00784911 |
Caterpillar Information System:
Use Proper Handling During Shipment and Installation of the Water Pumps{1361} Use Proper Handling During Shipment and Installation of the Water Pumps{1361}
G3408C and G3412C Engines Exhaust Bypass - Install
G3408C and G3412C Engines Exhaust Bypass - Remove
Product Identification Numbers (PIN) Location Guide Forwarder
3034 Industrial Engine Maintenance Interval Schedule
G3300 Engines Speed Sensor - Clean/Inspect
3500B Engines Turbocharger
G3408C and G3412C Engines Spark Plug Adapter - Remove and Install
G3408C and G3412C Engines Spark Plugs - Remove and Install
G3408C and G3412C Engines Transformer - Remove and Install
3054 and 3056 Marine Generator Sets Warning Alarm
UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies System Startup
3412C Engine Vibration Damper and Pulley
G3408C and G3412C Engines Exhaust Bypass - Assemble
2001/08/01 A New Pyrometer Is Available {7451, 7466}
Product Identification Numbers (PIN) Location Guide Skid Steer Loader
3412C Engine Fuel Transfer Pump
3412C Engine Fuel Injection Lines
G3408C and G3412C Engines Exhaust Manifold - Remove
UPS 250 and UPS 300 Uninterruptible Power Supplies Initial Startup Procedure - System Pre-startup
G3408C and G3412C Engines Exhaust Manifold - Install
3412C Engine Air Inlet and Exhaust Lines
G3408C and G3412C Engines Aftercooler - Remove
3412C Engine Fuel Injection Pump