Sea Water Strainer - Clean/Inspect
The sea water strainer must be clean in order to allow proper engine cooling. Check the sea water strainer for plugging. Inspect the sea water strainer more frequently if the vessel is being operated in water which is shallow or dirty. The sea water strainer protects the aftercooler from debris. The sea water strainer will catch pieces of the rubber impeller from the raw water pump due to a failure from debris. The sea water strainer is installed on turbocharged engines only.
Drain the Sea Water Cooling System
Turbocharged Engines
- Close the valve for the sea water.
- Disconnect both hoses (2) from the sea water pump (1) .
Show/hide table
Illustration 1 | g00751785 |
- Remove the drain plug (3) from the front cover of the heat exchanger (4). Ensure that the drain hole is not plugged.
Show/hide table
Illustration 2 | g00751786 |
- Use the turning tool on the front of the crankshaft in order to rotate the engine. This will ensure that all of the water has drained from the sea water pump.
Clean the Sea Water Strainer
Turbocharged Engines
- Ensure that the sea water cooling system is drained. Refer to "Drain the Sea Water Cooling System" for the procedure.
- Remove the hose clamp (2) for the sea water strainer. Remove the sea water strainer (1) and clean the screen. Use clean water to clean the screen. Remove any dirt and debris.
Show/hide table
Illustration 3 | g00752040 |
- Install the sea water strainer (1). Install the hose and the hose clamp (2). Fill the sea water strainer and the suction line for the auxiliary water pump with water.
Filling the Sea Water Cooling System
Turbocharged Engines
- Connect the hoses (2) at the sea water pump (1) .
Show/hide table
Illustration 4 | g00751785 |
- Install the drain plug (3) in the front cover of the heat exchanger (4) .
Show/hide table
Illustration 5 | g00751786 |
- Open the valve for the sea water.
Sea Water Cooling System for Naturally Aspirated Engines
Naturally aspirated engines do not have a sea water strainer. However, if the sea water cooling system needs to be drained, then use the following procedure:
Drain
- Close the valve for the sea water.
- Disconnect both hoses (2) from the sea water pump (1) .
Show/hide table
Illustration 6 | g00751785 |
- Remove hose clamp (3) and hose (4) for the marine gear oil cooler.
Show/hide table
Illustration 7 | g00751788 |
- Use the turning tool on the front of the crankshaft to rotate the engine. This will ensure that all of the water has drained from the sea water pump.
Fill
- Connect the hoses (2) at the sea water pump (1) .
Show/hide table
Illustration 8 | g00751785 |
- Install hose (4) for the marine gear oil cooler and hose clamp (3) .
Show/hide table
Illustration 9 | g00751788 |
- Open the valve for the sea water.
Caterpillar Information System:
G3406 Engine Governor - Adjust
3054, 3054B and 3056 Marine Engines Vibration Damper and Pulley - Remove and Install
G3304 and G3306 Engines Testing the Cooling System
G3406 Engine Visual Inspection
C7 and C9 On-Highway Engines Engine Misfires, Runs Rough or Is Unstable
3054 and 3056 Marine Generator Sets Fuel System Primary Filter (Water Separator) Element - Replace
C-10, C-12, C-15 and C-16 Industrial Engines Diagnostic Lamp Circuit - Test
G3304 and G3306 Engines Cylinder Block
UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Specifications
3054 and 3056 Marine Generator Sets Engine Oil and Filter - Change
G3406 Engine Ignition System
3126E On-highway Engine System Configuration Parameters
G3500 Engines Restriction of Air Inlet and Exhaust
3054 and 3056 Marine Generator Set Engines Rocker Arm and Shaft - Remove
3054, 3054B and 3056 Marine Engines Valve Mechanism Cover - Remove and Install - 3056 Engine
3054 and 3056 Marine Generator Set Engines Rocker Arm and Shaft - Install
3054 and 3056 Marine Generator Set Engines Expansion Tank - Remove and Install
3126B and 3126E On-highway Engines Check Engine Lamp Circuit - Test
C-10, C-12, C-15 and C-16 Industrial Engines Switch Circuits - Test
3054, 3054B and 3056 Marine Engines Reference Material
G3600 Engines Customer Passwords
3114, 3116, and 3126 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Injection Lines
UPS 250 and UPS 300 Uninterruptible Power Supplies Status Messages