Fan Motor (Hydraulic and Radiator Cooling) - Test - Measurement of Case Drain Oil
Show/hide table
所需工具     | ||
---|---|---|
零件号     | 说明     | 数量     |
6V-9509     | 端面密封螺塞     | 1     |
6V-8398     | O 形密封圈     | 1     |
    | 远置排放软管,内径为 27.2 mm (13/16 in)     |
1     |
    | 测量用容器     | 1     |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 将机器停放在水平地面上。
- 关闭发动机。
- 释放液压系统压力。 请参阅测试和调整, "液压系统压力 - 释放"。
- 将箱体排放软管 (3) 从接头 (2) 处断开。 将 6V-9509 端面密封螺塞 和 6V-8398 O 形密封圈 装入箱体排油软管 (3) 的开口端。
Show/hide table
图 1 | g00786988 |
(1) 风扇马达 (2) 接头 (3) 壳体泄油软管 |
- 将远置排放软管的一端连接至接头 (2) 。 将远程排放软管的另一端放入容器中以便测量箱体排油量。
- 起动发动机。
- 根据测试和调整, "风扇马达转速(液压和散热器冷却)- 测试和调整"设定固定风扇转速。
- 测量一分钟内的箱体排油量。
最大箱体排油量 ... 3 L/min (0.8 US gpm)
Caterpillar Information System:
VPG-25, VPG-35, VPG-45 and VPG-55 Work Tools Visual Inspection
VPG-25, VPG-35, VPG-45 and VPG-55 Work Tools Grapple
312C Excavator Engine Air Filter Secondary Element - Replace
311C U Excavator Hydraulic System Main Hydraulic System
Product Identification Numbers (PIN) Location Guide Track-Type Tractor
5110B Excavator Machine Systems Swivel - Assemble
Product Identification Numbers (PIN) Location Guide Excavator (Track)
BA22, BA25 and BA30 Angling Brooms Brooms - BA25
BA22, BA25 and BA30 Angling Brooms Brooms - BA22
311C U Excavator Hydraulic System General Information
311C Excavator Machine System Specifications Stick - 2250 mm (7 ft 5 inch)
5110B Excavator Machine Systems Track Tension Cylinder - Install
312C and 315C Excavators Tool Control System System 3: Relief Valve (Line) - Test and Adjust
315C Excavator Fuel Inlet Screen - Clean
5110B Excavator Machine Systems Control Valve (Implement and Travel) - Disassemble
315C Excavator Hydraulic System General Information
315C Excavator Hydraulic System Swivel
Instructions for the Use of the M300 Technician Software With a Laptop Computer{7620} Instructions for the Use of the M300 Technician Software With a Laptop Computer{7620}
VPG-25, VPG-35, VPG-45 and VPG-55 Work Tools Grapple - Disassemble
5110B Excavator Machine Systems Bucket - Remove and Install
VPG-25, VPG-35, VPG-45 and VPG-55 Work Tools Grapple - Disassemble
VPG-25, VPG-35, VPG-45 and VPG-55 Work Tools Grapple - Disassemble
Installation of the Blank Hooks{6530, 6700} Installation of the Blank Hooks{6530, 6700}
311C Excavator Machine System Specifications Hydraulic Control (Straight Travel)