Grapple
Show/hide table
Illustration 1 | g00570594 |
Note: Refer to Illustration 1 for the section views of the Mechanical Grapple.
Use the following formulas to determine if you need to replace the bushings or the pins:
- If the inside diameter of the bushing is greater than the original inside diameter of the bushing plus 1 mm (0.04 inch), replace the bushing.
- If the outside diameter of the pin is less than the outside diameter of the new pin minus 2 mm (0.08 inch), replace the pin.
Show/hide table
Illustration 2 | g00729759 |
(1) Inside diameter of the new bushing
- VPG-25 ... 80 mm (3.15 inch)
- VPG-35 ... 80 mm (3.15 inch)
- VPG-45 ... 100 mm (3.94 inch)
- VPG-55 ... 100 mm (3.94 inch)
- VPG-35 ... 80 mm (3.15 inch)
(2) Outside diameter of the new pin
- VPG-25 ... 80 mm (3.15 inch)
- VPG-35 ... 80 mm (3.15 inch)
- VPG-45 ... 100 mm (3.94 inch)
- VPG-55 ... 100 mm (3.94 inch)
- VPG-35 ... 80 mm (3.15 inch)
Show/hide table
Illustration 3 | g00729767 |
(1) Inside diameter of the new bushing
- VPG-25 ... 80 mm (3.15 inch)
- VPG-35 ... 80 mm (3.15 inch)
- VPG-45 ... 100 mm (3.94 inch)
- VPG-55 ... 100 mm (3.94 inch)
- VPG-35 ... 80 mm (3.15 inch)
(2) Outside diameter of the new pin
- VPG-25 ... 80 mm (3.15 inch)
- VPG-35 ... 80 mm (3.15 inch)
- VPG-45 ... 100 mm (3.94 inch)
- VPG-55 ... 100 mm (3.94 inch)
- VPG-35 ... 80 mm (3.15 inch)
Show/hide table
Illustration 4 | g00729769 |
(1) Inside diameter of the new bushing
- VPG-25 ... 80 mm (3.15 inch)
- VPG-35 ... 80 mm (3.15 inch)
- VPG-45 ... 100 mm (3.94 inch)
- VPG-55 ... 100 mm (3.94 inch)
- VPG-35 ... 80 mm (3.15 inch)
Caterpillar Information System:
312C Excavator Engine Air Filter Secondary Element - Replace
311C U Excavator Hydraulic System Main Hydraulic System
Product Identification Numbers (PIN) Location Guide Track-Type Tractor
5110B Excavator Machine Systems Swivel - Assemble
Product Identification Numbers (PIN) Location Guide Excavator (Track)
BA22, BA25 and BA30 Angling Brooms Brooms - BA25
BA22, BA25 and BA30 Angling Brooms Brooms - BA22
311C U Excavator Hydraulic System General Information
311C Excavator Machine System Specifications Stick - 2250 mm (7 ft 5 inch)
5110B Excavator Machine Systems Track Tension Cylinder - Install
365B and 365B Series II Excavators Hydraulic System Fan Motor Speed (Hydraulic and Radiator Cooling) - Test and Adjust
BA22, BA25 and BA30 Angling Brooms Brooms - BA30
VPG-25, VPG-35, VPG-45 and VPG-55 Work Tools Visual Inspection
365B and 365B Series II Excavators Hydraulic System Fan Motor (Hydraulic and Radiator Cooling) - Test - Measurement of Case Drain Oil
312C and 315C Excavators Tool Control System System 3: Relief Valve (Line) - Test and Adjust
315C Excavator Fuel Inlet Screen - Clean
5110B Excavator Machine Systems Control Valve (Implement and Travel) - Disassemble
315C Excavator Hydraulic System General Information
315C Excavator Hydraulic System Swivel
Instructions for the Use of the M300 Technician Software With a Laptop Computer{7620} Instructions for the Use of the M300 Technician Software With a Laptop Computer{7620}
VPG-25, VPG-35, VPG-45 and VPG-55 Work Tools Grapple - Disassemble
5110B Excavator Machine Systems Bucket - Remove and Install
VPG-25, VPG-35, VPG-45 and VPG-55 Work Tools Grapple - Disassemble
VPG-25, VPG-35, VPG-45 and VPG-55 Work Tools Grapple - Disassemble