Cylinder Head - Remove
拆卸步骤
Show/hide table
需要的工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连接支架     | 2     |
开始:
- 拆下摇臂和摇臂轴。 请参阅解体和组装, "摇臂和摇臂轴 - 拆卸"。
- 拆下单体喷油器。 请参阅解体和组装, "单体喷油器 - 拆卸"。
- 拆下交流发电机。 请参阅解体和组装, "交流发电机 - 拆卸和安装"。
- 拆下气门机构盖座。 请参阅解体和组装, "气门机构盖座 - 拆卸和安装"。
- 从冷却系统将冷却液排入合适的容器以便保存或废弃这些冷却液。 请参阅操作和保养手册, "加注容量和建议"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 拆下附件驱动总成 (1) 。
Show/hide table
图 1 | g01063034 |
- 断开管路总成 (3) 和 (4) 。
- 拆下管路组件 (2) 。
- 断开软管 (5) 。
- 断开软管组件 (6) 和 (7) 。
Show/hide table
图 2 | g01142119 |
- 断开传感器。
- 在缸盖 (9) 上固定工具 (A) 和适当的提升装置。 缸盖 (9) 的重量约为 147 kg (325 lb)。
- 拆下螺栓 (8) 。 拆下缸盖 (9) 和密封垫。
Caterpillar Information System:
SR4 and SR4B Electric Power Generation Rewind Data General Information
C-9 Engines for Caterpillar Built Machines Aftercooler - Test
3054 and 3056 Industrial and Generator Set Engines Turbocharger
3003, 3013, 3014 and 3024 Industrial Engines Starting the Engine
C9 Engines for Caterpillar Built Machines Crankshaft - Install
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0276 - FMI 13 Left Turbo Inlet Pressure calibration required
3054E and 3056E Industrial Engines Engine Starting
C-9 Engines for Caterpillar Built Machines Inlet Manifold Pressure - Test
C9 Engines for Caterpillar Built Machines Crankshaft - Remove
3176C and 3196 Industrial Engines Air Compressor Drive Gear - Install
3612 and 3616 Engines Vibration Damper - Install
3176C and 3196 Industrial Engines Air Compressor Drive Gear - Remove
3512B Marine Auxiliary Engines Barring Group - Remove and Install
69D, 769D, 773D, 773E, 776D and 777D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Power Train Electronic Control System Electrical Connector - Inspect
C9 Engine For Caterpillar Built Machines Cylinder Head - Install
3512B Marine Auxiliary Engines Prelubrication Oil Pump - Remove and Install
3512B Marine Auxiliary Engines Jacket Water Heater - Remove and Install
C9 Engine For Caterpillar Built Machines Lifter Group - Remove and Install
C-18 Truck Engines Customer Specified Parameters
C-9 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
3512B Marine Auxiliary Engines Electronic Control Module (Engine) - Remove and Install
3512B Marine Auxiliary Engines Fuel Filter Housing - Remove
3512B Marine Auxiliary Engines Fuel Filter Housing - Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove - 3013, 3014 and 3024 Engines