Vibration Damper - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 8T-0914 (1)     | 导向销     | 2     |
B     | 1U-9392 (1)     | 减振器导向销     | 2     |
Show/hide table
( 1 ) | 9U-5105 发动机工具总成 中的零件 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将工具 (A) 安装在曲轴中。
Show/hide table
图 1 | g00609918 |
- 将隔套 (5) 置于工具 (A) 上。 确保将接头组件固定在一起的螺栓头与隔套 (5) 中的孔配合紧密。
- 通过减振器 (4) 的中央安装一个合适的起吊设备。 窄型减振器的重量约为 288 kg (639 lb)。 宽型减振器的重量约为 402 kg (882 lb)。
Show/hide table
图 2 | g01294025 |
- 将减振器 (4) 置于工具 (A) 上。 将减振器 (4) 上的上止点位置的正时标记和曲轴上的正时标记对齐。 确保对准了螺栓孔。 务必使减震器中央的小螺栓头与隔套配合紧密。 安装减振器 (4) 。
- 在工具 (A) 上安装接头 (3) 。 确保对准了螺栓孔。 务必使减震器 (4) 中央的小螺栓头与隔套 (3) 配合紧密。
Show/hide table
图 3 | g01294011 |
- 安装将接头固定到曲轴上的螺栓。 按照对角模式拧紧螺钉至 1350 ± 150 N·m (1000 ± 110 lb ft) 的扭矩。
- 拆下工具 (A) ,并在接头 (3) 中安装工具 (B) 。
注: 确保以正确的方向安装外部减振器。 应将上止点位置正时标记以顺时针方向从减振器 (4) 上的上止点位置正时标记转动 36 度。 当从发动机前部查看减振器时,决定方向。
- 通过减振器 (2) 的中央安装一个合适的起吊设备。 窄型减振器的重量约为 288 kg (639 lb)。 宽型减振器的重量约为 402 kg (886 lb)。
Show/hide table
图 4 | g00609906 |
Show/hide table
图 5 | g00609902 |
双重减振器 |
- 安装减振器 (2) 。 确保将振动器中的螺栓孔与接口中的螺纹孔对齐。 确保使减震器 (2) 中央的小螺栓头与隔套配合紧密。
- 安装将减振器 (2) 固定在接头上的螺栓 (1) 。 拆下工具 (B) 。 安装其余的螺栓 (1) 。 按照对角模式拧紧螺钉至 1350 ± 150 N·m (1000 ± 110 lb ft) 的扭矩。
Caterpillar Information System:
3176C and 3196 Industrial Engines Air Compressor Drive Gear - Remove
3612 and 3616 Engines Vibration Damper - Remove
C9 Engine For Caterpillar Built Machines Belt Tensioner - Remove and Install
C9 Engine For Caterpillar Built Machines Engine Oil Cooler - Install
C9 Engine For Caterpillar Built Machines Engine Oil Cooler - Remove
3056 Engine for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C9 Engine For Caterpillar Built Machines Fuel Filter Base - Remove and Install
C-9 Engines for Caterpillar Built Machines Air Inlet and Exhaust System - Inspect
3054, 3054B and 3056 Marine Engines Cylinder Head
C9 Engine For Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C9 Urban Transit Bus Engine Engine Description
3612 and 3616 Engines Accessory Drive - Assemble
3176C and 3196 Industrial Engines Air Compressor Drive Gear - Install
C9 Engines for Caterpillar Built Machines Crankshaft - Remove
C-9 Engines for Caterpillar Built Machines Inlet Manifold Pressure - Test
3054E and 3056E Industrial Engines Engine Starting
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0276 - FMI 13 Left Turbo Inlet Pressure calibration required
C9 Engines for Caterpillar Built Machines Crankshaft - Install
3003, 3013, 3014 and 3024 Industrial Engines Starting the Engine
3054 and 3056 Industrial and Generator Set Engines Turbocharger
C-9 Engines for Caterpillar Built Machines Aftercooler - Test
SR4 and SR4B Electric Power Generation Rewind Data General Information
C9 Engine For Caterpillar Built Machines Cylinder Head - Remove
3512B Marine Auxiliary Engines Barring Group - Remove and Install