Engine Oil Cooler - Remove
拆卸步骤
开始:
- 拆下发动机机油滤清器座。 请参阅解体和组装, "发动机机油滤清器座 - 拆卸"。
Show/hide table
热的冷却液、蒸汽和碱会造成人身伤害。 在工作温度下,发动机冷却液是热的而且处在压力下。 散热器和所有到加热器的管路或发动机中都有热的冷却液或蒸汽。 与它们的任何接触都会造成严重烫伤。 只有当发动机停机且冷却系统压力盖已经冷却到可以徒手触摸时,再慢慢拆下冷却系统压力盖以释放压力。 不要试图在冷却液还热的时候去拧紧软管接头,软管会脱落而造成灼伤。 警告:冷却系统的冷却液添加剂含碱。 应避免它与皮肤和眼睛接触。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 拆下发动机机油泵 (1) 和密封垫。
Show/hide table
图 1 | g00952338 |
Caterpillar Information System:
3056 Engine for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C9 Engine For Caterpillar Built Machines Fuel Filter Base - Remove and Install
C-9 Engines for Caterpillar Built Machines Air Inlet and Exhaust System - Inspect
3054, 3054B and 3056 Marine Engines Cylinder Head
C9 Engine For Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C9 Urban Transit Bus Engine Engine Description
3612 and 3616 Engines Accessory Drive - Assemble
3126B and 3126E On-highway Engines Driver Questionnaire Response
3618 Engine Crankshaft Rear Seal and Wear Sleeve - Install
3618 Engine Crankshaft Rear Seal and Wear Sleeve - Remove
3056 Engine for Caterpillar Built Machines Pistons and Connecting Rods - Install
C9 On-highway Engines Refill Capacities
C9 Engine For Caterpillar Built Machines Engine Oil Cooler - Install
C9 Engine For Caterpillar Built Machines Belt Tensioner - Remove and Install
3612 and 3616 Engines Vibration Damper - Remove
3176C and 3196 Industrial Engines Air Compressor Drive Gear - Remove
3612 and 3616 Engines Vibration Damper - Install
3176C and 3196 Industrial Engines Air Compressor Drive Gear - Install
C9 Engines for Caterpillar Built Machines Crankshaft - Remove
C-9 Engines for Caterpillar Built Machines Inlet Manifold Pressure - Test
3054E and 3056E Industrial Engines Engine Starting
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0276 - FMI 13 Left Turbo Inlet Pressure calibration required
C9 Engines for Caterpillar Built Machines Crankshaft - Install
3003, 3013, 3014 and 3024 Industrial Engines Starting the Engine