Inlet Manifold Pressure - Test
通过比较进气歧管的压力与 技术营销信息 (TMI) 中规定的信息,即可检查发动机的效率。 应在发动机功率下降,但是发动机又没有切实的故障迹象时采用本测试。
TMI 中还列出了进气歧管的正确压力。 这一信息资料是在下述工况下拟定的:
- 干式大气压力为
99 kPa (29.7 in Hg) - 外部气温为
29 °C (85 °F) - 温度在
16 °C (60 °F) 时美国石油学会 (API) 比重指数为35 API 的燃油
对于增压中冷式发动机,功率会随燃油的比重指数的不同而变化。 进气歧管压力会随燃油的比重指数的不同而变化。 如果燃油等级高于 35 API,则进气歧管的压力可能会低于 TMI 中规定的压力值。 如果燃油等级低于 35 API,则进气歧管的压力可能会高于 TMI 中列出的压力值。
注: 检查进气歧管压力时,应确保进气和排气没有受阻。
Show/hide table
图 1 | g01130168 |
(1) 增压压力传感器 |
Show/hide table
需要的工具 | ||
零件号 | 零件名 | 数量 |
1U-5470
或者 198-4240 |
发动机压力表总成
或者 数字式压力指示仪 |
1 |
Show/hide table
图 2 | g00293196 |
1U-5470 发动机压力表总成 |
请参阅专门说明书 , SEHS8907, " 1U-5470 发动机压力表总成的使用 ",了解使用 1U-5470 发动机压力表总成 时需要的说明。
使用下述程序测量进气歧管压力:
- 从缸盖上拆下增压压力传感器 ( 1)。
- 在缸盖的测压位置连接 1U-5470 发动机压力表总成 。
注: 必须使用 T 形管或一些其它管路部件,以使增压压力传感器 ( 1) 连接在测试位置上。
- 记录数值。
- 比较程序 3 中记录的数值与 TMI 中规定的压力值。
Caterpillar Information System:
C9 Engines for Caterpillar Built Machines Crankshaft - Remove
3176C and 3196 Industrial Engines Air Compressor Drive Gear - Install
3612 and 3616 Engines Vibration Damper - Install
3176C and 3196 Industrial Engines Air Compressor Drive Gear - Remove
3612 and 3616 Engines Vibration Damper - Remove
C9 Engine For Caterpillar Built Machines Belt Tensioner - Remove and Install
C9 Engine For Caterpillar Built Machines Engine Oil Cooler - Install
C9 Engine For Caterpillar Built Machines Engine Oil Cooler - Remove
3056 Engine for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C9 Engine For Caterpillar Built Machines Fuel Filter Base - Remove and Install
C-9 Engines for Caterpillar Built Machines Air Inlet and Exhaust System - Inspect
3054, 3054B and 3056 Marine Engines Cylinder Head
3054E and 3056E Industrial Engines Engine Starting
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0276 - FMI 13 Left Turbo Inlet Pressure calibration required
C9 Engines for Caterpillar Built Machines Crankshaft - Install
3003, 3013, 3014 and 3024 Industrial Engines Starting the Engine
3054 and 3056 Industrial and Generator Set Engines Turbocharger
C-9 Engines for Caterpillar Built Machines Aftercooler - Test
SR4 and SR4B Electric Power Generation Rewind Data General Information
C9 Engine For Caterpillar Built Machines Cylinder Head - Remove
3512B Marine Auxiliary Engines Barring Group - Remove and Install
69D, 769D, 773D, 773E, 776D and 777D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Power Train Electronic Control System Electrical Connector - Inspect
C9 Engine For Caterpillar Built Machines Cylinder Head - Install
3512B Marine Auxiliary Engines Prelubrication Oil Pump - Remove and Install