Cylinder Head - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
B     | 4C-5593     | 防粘结剂     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 在发动机机上定位新密封垫。
- 将工具 (A) 和适当的起吊设备固定到缸盖 (9) 上。 缸盖 (9) 的重量约为 147 kg (325 lb)。 在发动机缸体中的定位销上定位缸盖。
Show/hide table
图 1 | g01142119 |
- 将工具 (B) 涂抹在螺栓 (8) 的螺纹上。 安装螺栓 (8) 。 有关正确紧固步骤,请参阅技术参数, "缸盖"。
拧紧缸盖两端高压机油道孔塞(图上未显示)到以下扭矩 285 ± 25 N·m (210 ± 18 lb ft)。
- 连接传感器。
- 连接软管组件 (6) 和 (7) 。
- 连接软管 (5) 。
Show/hide table
图 2 | g01063034 |
- 安装管路组件 (2) 。
- 连接管组件 (3) 和 (4) 。
- 安装附件驱动总成 (1) 。
- 加注冷却系统。 请参阅操作和保养手册, "加注容量和建议"。
End By:
- 安装气门机构罩盖底座。 请参阅 拆解和组装, "气门机构罩盖底座 - 拆卸和安装"。
- 安装交流发电机。 请参阅 拆解和组装, "交流发电机 - 拆卸和安装"。
- 安装单体喷油器。 请参阅 拆解和组装, "单体喷油器 - 安装"。
- 安装摇臂和摇臂轴。 请参阅 拆解和组装, "摇臂和轴 - 安装"。
Caterpillar Information System:
69D, 769D, 773D, 773E, 776D and 777D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Power Train Electronic Control System Electrical Connector - Inspect
3512B Marine Auxiliary Engines Barring Group - Remove and Install
C9 Engine For Caterpillar Built Machines Cylinder Head - Remove
SR4 and SR4B Electric Power Generation Rewind Data General Information
C-9 Engines for Caterpillar Built Machines Aftercooler - Test
3054 and 3056 Industrial and Generator Set Engines Turbocharger
3003, 3013, 3014 and 3024 Industrial Engines Starting the Engine
C9 Engines for Caterpillar Built Machines Crankshaft - Install
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0276 - FMI 13 Left Turbo Inlet Pressure calibration required
3054E and 3056E Industrial Engines Engine Starting
C-9 Engines for Caterpillar Built Machines Inlet Manifold Pressure - Test
C9 Engines for Caterpillar Built Machines Crankshaft - Remove
3512B Marine Auxiliary Engines Prelubrication Oil Pump - Remove and Install
3512B Marine Auxiliary Engines Jacket Water Heater - Remove and Install
C9 Engine For Caterpillar Built Machines Lifter Group - Remove and Install
C-18 Truck Engines Customer Specified Parameters
C-9 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
3512B Marine Auxiliary Engines Electronic Control Module (Engine) - Remove and Install
3512B Marine Auxiliary Engines Fuel Filter Housing - Remove
3512B Marine Auxiliary Engines Fuel Filter Housing - Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove - 3013, 3014 and 3024 Engines
3054, 3054B and 3056 Marine Engines Engine Oil Pump
C-15, C-16, and C-18 Engines Electronic Control System Components
3512B Marine Auxiliary Engines Turbocharger - Remove