Customer Specified Parameters
To record programmed specifications, use the following blanks.
Customer Passwords
- First Password ____________________
- Second Password ____________________
Power Rating (hp at rpm) ____________________
Rating Selection (A-E) ____________________
Vehicle ID ____________________
Vehicle Speed Parameters
- Vehicle Speed Calibration ____________________
pulses per km (pulses per mile) - Vehicle Speed Limit ____________________
km/h (mph) - Vehicle Speed Limit Protection ____________________
- Tachometer Calibration ____________________ pulses per revolution
- Soft Vehicle Speed Limit ____________________
Cruise Control Parameters
- Low Cruise Control Speed Set Limit ____________________
km/h (mph) - High Cruise Control Speed Set Limit ____________________
km/h (mph) - Engine Brake ____________________
- Cruise/Idle/PTO Switch Configuration ____________________
- Soft Cruise Control ____________________
Idle Parameters
- Idle Vehicle Speed Limit ____________________
km/h (mph) - Idle RPM Limit ____________________
- PTO Engine Speed Ramp Rate ____________________ rpm/sec
- PTO Bump RPM ____________________
PTO Parameters
- PTO Configuration ____________________
- PTO Top Engine Limit ____________________
- PTO Engine RPM Set Speed ____________________
- PTO Engine RPM Set Speed A ____________________
- PTO Engine RPM Set Speed B ____________________
- PTO to Set Speed ____________________
- PTO Cab Throttle RPM Limit ____________________
- PTO Vehicle Speed Limit ____________________
- Torque Limit ____________________
N·m (lb ft) - PTO Shutdown Time ____________________
- PTO Shutdown Timer Maximum RPM ____________________
- PTO Activation of Cooling Fan (If Equipped) ____________________
Engine/Gear Speed Limit Parameters
- Lower Gears Engine RPM Limit ____________________
- Lower Gears Turn Off Speed ____________________
km/h (mph) - Intermediate Gears Engine RPM Limit ____________________
- Intermediate Gears Turn Off Speed ____________________
km/h (mph) - Gear Down Protection RPM Limit ____________________
- Gear Down Protection Turn On Speed ____________________
km/h (mph) - Low Idle Engine RPM ____________________
- Transmission Style (If Equipped) ____________________
Timer Parameters
- Idle Shutdown Time ____________________
- Idle Shutdown Timer Maximum RPM ____________________
- Idle Shutdown Override Allowance ____________________
- Minimum Shutdown Idle Shutdown Outside Temperature ____________________
- Maximum Shutdown Idle Shutdown Outside Temperature ____________________
- A/C Pressure Switch Fan On - Time (If Equipped) ____________________
- Fan with Engine Brake On - Full (If Equipped) ____________________
- Engine Compression Brake Delay ____________________
Smart Idle Parameters
- Battery Monitor and Engine Speed Control Voltage ____________________
Engine Monitoring Parameters
- Engine Monitoring Mode ____________________
- Coolant Level Sensor (If Equipped) ____________________
Maintenance Indicator Parameters
- Maintenance Indicator Mode ____________________
- PM 1 Interval (Manual) ____________________
- Engine Oil Capacity (Automatic) ____________________
Trip Parameters
- Dash - PM Level 1 Reset ____________________
- Dash - Fleet Trip Reset ____________________
- Dash - State Selection ____________________
- Theft Deterrent System Control ____________________
- Theft Deterrent Password ____________________
Vehicle Activity Report
- Minimum Idle Time ____________________
Driver Incentive
- Driver Incentive Enable ____________________
Output Parameters
- Fan Control Type (If Equipped) ____________________
Data Link Parameters
- Powertrain Data Link ____________________
Caterpillar Information System:
C9 Engine For Caterpillar Built Machines Lifter Group - Remove and Install
3512B Marine Auxiliary Engines Jacket Water Heater - Remove and Install
3512B Marine Auxiliary Engines Prelubrication Oil Pump - Remove and Install
C9 Engine For Caterpillar Built Machines Cylinder Head - Install
69D, 769D, 773D, 773E, 776D and 777D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Power Train Electronic Control System Electrical Connector - Inspect
3512B Marine Auxiliary Engines Barring Group - Remove and Install
C9 Engine For Caterpillar Built Machines Cylinder Head - Remove
SR4 and SR4B Electric Power Generation Rewind Data General Information
C-9 Engines for Caterpillar Built Machines Aftercooler - Test
3054 and 3056 Industrial and Generator Set Engines Turbocharger
3003, 3013, 3014 and 3024 Industrial Engines Starting the Engine
C9 Engines for Caterpillar Built Machines Crankshaft - Install
C-9 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
3512B Marine Auxiliary Engines Electronic Control Module (Engine) - Remove and Install
3512B Marine Auxiliary Engines Fuel Filter Housing - Remove
3512B Marine Auxiliary Engines Fuel Filter Housing - Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove - 3013, 3014 and 3024 Engines
3054, 3054B and 3056 Marine Engines Engine Oil Pump
C-15, C-16, and C-18 Engines Electronic Control System Components
3512B Marine Auxiliary Engines Turbocharger - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft - Disassemble - 3013, 3014 and 3024 Engines
3056E Industrial Engine Engine Oil Bypass Valve
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft - Assemble - 3013, 3014, and 3024 Engines
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install