Jacket Water Heater - Remove and Install
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Drain the coolant from the jacket water system into a suitable container for storage or for disposal.
Show/hide table
Illustration 1 g00634874 - Disconnect the electrical connection (not shown) from the jacket water heater.
- Remove plug (1) in order to drain the coolant from the jacket water heater. After the coolant has drained, install the plug.
Show/hide table
Illustration 2 g00634914 - Disconnect two hose assemblies (2) from jacket water heater (3).
- Remove four bolts and washers (4) that attach the plates and the jacket water heater to the bracket.
- Remove the jacket water heater.
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Place jacket water heater (3) into position in the plates on the bracket. Install four bolts and washers (4) that attach the plates and the jacket water heater to the bracket.
- Connect two hose assemblies (2) to jacket water heater (3).
- Connect the electrical connection (not shown) to jacket water heater (3).
- Fill the jacket water cooling system. For the proper coolant to use, see the Operation and Maintenance Manual.
Show/hide table
| |
| Illustration 3 | g00634914 |
Caterpillar Information System:
3512B Marine Auxiliary Engines Prelubrication Oil Pump - Remove and Install
C9 Engine For Caterpillar Built Machines Cylinder Head - Install
69D, 769D, 773D, 773E, 776D and 777D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Power Train Electronic Control System Electrical Connector - Inspect
3512B Marine Auxiliary Engines Barring Group - Remove and Install
C9 Engine For Caterpillar Built Machines Cylinder Head - Remove
SR4 and SR4B Electric Power Generation Rewind Data General Information
C-9 Engines for Caterpillar Built Machines Aftercooler - Test
3054 and 3056 Industrial and Generator Set Engines Turbocharger
3003, 3013, 3014 and 3024 Industrial Engines Starting the Engine
C9 Engines for Caterpillar Built Machines Crankshaft - Install
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0276 - FMI 13 Left Turbo Inlet Pressure calibration required
3054E and 3056E Industrial Engines Engine Starting
C9 Engine For Caterpillar Built Machines Lifter Group - Remove and Install
C-18 Truck Engines Customer Specified Parameters
C-9 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
3512B Marine Auxiliary Engines Electronic Control Module (Engine) - Remove and Install
3512B Marine Auxiliary Engines Fuel Filter Housing - Remove
3512B Marine Auxiliary Engines Fuel Filter Housing - Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove - 3013, 3014 and 3024 Engines
3054, 3054B and 3056 Marine Engines Engine Oil Pump
C-15, C-16, and C-18 Engines Electronic Control System Components
3512B Marine Auxiliary Engines Turbocharger - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft - Disassemble - 3013, 3014 and 3024 Engines
3056E Industrial Engine Engine Oil Bypass Valve