Prelubrication Oil Pump - Remove and Install
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Remove the O-ring seal from the joint between the tube assembly and the prelubrication oil pump. Discard the O-ring seal.
- Disconnect tube assembly (2) from prelubrication oil pump (1). Remove the O-ring seal from the joint between the tube assembly and the prelubrication oil pump. Discard the O-ring seal.
Show/hide table
Illustration 2 g00933002 - Disconnect tube assembly (2) from prelubrication oil pump (1).
- Remove the bolts (4) that attach prelubrication oil pump (1) to bracket (5). Remove prelubrication oil pump (1).
Show/hide table
| |
| Illustration 1 | g00933001 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Place prelubrication oil pump (1) into position on bracket (5). Install bolts (4) that attach the prelubrication oil pump to the bracket.
- Install a new O-ring seal for the joint between tube assembly (3) and prelubrication oil pump (1). Connect the tube assembly to the prelubrication oil pump.
Show/hide table
Illustration 4 g00933001 - Install a new O-ring seal for the joint between tube assembly (2) and prelubrication oil pump (1). Connect the tube assembly to the prelubrication oil pump.
Show/hide table
| |
| Illustration 3 | g00933002 |
Caterpillar Information System:
C9 Engine For Caterpillar Built Machines Cylinder Head - Install
69D, 769D, 773D, 773E, 776D and 777D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Power Train Electronic Control System Electrical Connector - Inspect
3512B Marine Auxiliary Engines Barring Group - Remove and Install
C9 Engine For Caterpillar Built Machines Cylinder Head - Remove
SR4 and SR4B Electric Power Generation Rewind Data General Information
C-9 Engines for Caterpillar Built Machines Aftercooler - Test
3054 and 3056 Industrial and Generator Set Engines Turbocharger
3003, 3013, 3014 and 3024 Industrial Engines Starting the Engine
C9 Engines for Caterpillar Built Machines Crankshaft - Install
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0276 - FMI 13 Left Turbo Inlet Pressure calibration required
3054E and 3056E Industrial Engines Engine Starting
C-9 Engines for Caterpillar Built Machines Inlet Manifold Pressure - Test
3512B Marine Auxiliary Engines Jacket Water Heater - Remove and Install
C9 Engine For Caterpillar Built Machines Lifter Group - Remove and Install
C-18 Truck Engines Customer Specified Parameters
C-9 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
3512B Marine Auxiliary Engines Electronic Control Module (Engine) - Remove and Install
3512B Marine Auxiliary Engines Fuel Filter Housing - Remove
3512B Marine Auxiliary Engines Fuel Filter Housing - Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove - 3013, 3014 and 3024 Engines
3054, 3054B and 3056 Marine Engines Engine Oil Pump
C-15, C-16, and C-18 Engines Electronic Control System Components
3512B Marine Auxiliary Engines Turbocharger - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft - Disassemble - 3013, 3014 and 3024 Engines