Vibration Damper - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 8T-0914 (1)     | 导向销     | 2     |
B     | 1U-9392 (1)     | 减振器导向销     | 2     |
Show/hide table
( 1 ) | 9U-5105 发动机工具总成 中的零件 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 根据合适的应用选择正确的工具。
- 拆下将减振器 (2) 固定入位的两个螺栓 (1) 。 将工具 (B) 安装在适配器中。
Show/hide table
图 1 | g00609902 |
双重减振器 |
Show/hide table
图 2 | g00609906 |
注: 以后的减振器带有翅式护盖。 小心不要损坏翅片。
- 通过减振器 (2) 的中央安装一个合适的起吊设备。 窄型减振器的重量约为 288 kg (639 lb)。 宽型减振器的重量约为 402 kg (886 lb)。
- 拆下将减振器 (2) 固定到接头的其余螺栓 (1) 。 沿着工具 (B) 滑动减振器,并拆下减振器 (2) 。 拆下工具 (B) 。
- 拆下固定接头 (3) 和减振器 (4) 的两个顶部螺栓。 安装工具 (A) 。
Show/hide table
图 3 | g01294011 |
- 拆下剩余的螺栓,然后拆下接头 (3) 。
- 将减振器 (4) 移动工具 (A) 上,直至可以通过减振器 (4) 的中央放置一个合适的举升设备。
Show/hide table
图 4 | g01294025 |
- 通过减振器 (4) 的中央安装一个合适的起吊设备。 窄型减振器的重量约为 288 kg (639 lb)。 宽型减振器的重量约为 402 kg (882 lb)。 拆卸减振器 (4) 。
- 拆下隔套 (5) 。
注: 有关重新装配减振器的信息,请参阅再使用和修补指南, SEBF8152, "为3600系列发动机重新装配减振器的步骤"。
Show/hide table
图 5 | g00609918 |
Caterpillar Information System:
C9 Engine For Caterpillar Built Machines Belt Tensioner - Remove and Install
C9 Engine For Caterpillar Built Machines Engine Oil Cooler - Install
C9 Engine For Caterpillar Built Machines Engine Oil Cooler - Remove
3056 Engine for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C9 Engine For Caterpillar Built Machines Fuel Filter Base - Remove and Install
C-9 Engines for Caterpillar Built Machines Air Inlet and Exhaust System - Inspect
3054, 3054B and 3056 Marine Engines Cylinder Head
C9 Engine For Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C9 Urban Transit Bus Engine Engine Description
3612 and 3616 Engines Accessory Drive - Assemble
3126B and 3126E On-highway Engines Driver Questionnaire Response
3618 Engine Crankshaft Rear Seal and Wear Sleeve - Install
3176C and 3196 Industrial Engines Air Compressor Drive Gear - Remove
3612 and 3616 Engines Vibration Damper - Install
3176C and 3196 Industrial Engines Air Compressor Drive Gear - Install
C9 Engines for Caterpillar Built Machines Crankshaft - Remove
C-9 Engines for Caterpillar Built Machines Inlet Manifold Pressure - Test
3054E and 3056E Industrial Engines Engine Starting
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0276 - FMI 13 Left Turbo Inlet Pressure calibration required
C9 Engines for Caterpillar Built Machines Crankshaft - Install
3003, 3013, 3014 and 3024 Industrial Engines Starting the Engine
3054 and 3056 Industrial and Generator Set Engines Turbocharger
C-9 Engines for Caterpillar Built Machines Aftercooler - Test
SR4 and SR4B Electric Power Generation Rewind Data General Information