Flywheel Housing - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7573     | 连杆支架     | 2     |
开始:
- 拆下飞轮。 请参阅拆解和组装, "飞轮 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 在飞轮壳 (1) 上固定工具 (A) 和适当的提升装置。
Show/hide table
图 1 | g01027146 |
- 拆下用于将飞轮壳体固定到缸体上的螺栓 (2) 和螺栓 (3) 。
- 卸下螺栓 (4) 。 拆下飞轮壳 (1) 。 飞轮壳 (1) 的重量约为 25 kg (55 lb)。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7573     | 连杆支架     | 2     |
B     | 1U-8846     | 密封垫密封胶     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 安装之前先在飞轮壳整个安装面上涂抹工具 (B) 。
- 在飞轮壳 (1) 上固定工具 (A) 和适当的提升装置。 飞轮壳 (1) 的重量约为 25 kg (55 lb)。 将飞轮壳体 (1) 定位在缸体上。 安装螺栓 (4) 。
Show/hide table
图 2 | g01027146 |
- 安装螺栓 (2) 和螺栓 (3) 。
End By: 安装飞轮。 请参阅 拆解和组装, "飞轮 - 安装"。
Caterpillar Information System:
307B Excavator Indicators and Gauges - Test
3064 and 3066 Engines for Caterpillar Built Machines Camshaft Bearings - Install
BP15 Pickup Broom Wire Bristle (Gutter Brush) - Inspect/Replace
307B Excavator Blade Linkage - Lubricate
BP15 Pickup Broom Gutter Brush Adjustment
3126B Engines for Caterpillar Built Machines Crankshaft Front Seal - Install
3126B Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove
307B Excavator Machine Systems Blade Cylinder - Disassemble
307B Excavator Machine System Specifications Relief Valve (Pilot)
3524B Engine for Caterpillar Built Machines Crankshaft Main Bearings - Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Solenoid Valve (Counterweight Circuit) - Install
C-9 Engines for Caterpillar Built Machines Water Temperature Regulator Housing
307B Excavator Overload Warning Device
307B Excavator Seat Heater - If Equipped
3524B Engine for Caterpillar Built Machines Pistons and Connecting Rods - Remove
330B Excavator Material Handler Machine Systems Boom Cylinder - Remove
C-9 Engines for Caterpillar Built Machines Engine Oil Pan
3524B Engine for Caterpillar Built Machines Pistons and Connecting Rods - Install
C15 and C18 Petroleum Generator Sets Engine Operation with Intermittent Diagnostic Codes
3114, 3116 and 3126 MUI Engine Governors Installation of Governor on 1U7326 Governor Calibration Bench
307B Excavator Machine Systems Blade Cylinder - Assemble
307B Excavator Quick Coupler Control - If Equipped
BP15 Pickup Broom Maintenance Interval Schedule
307B Excavator Implement Changing