Turbocharger - Remove
拆卸步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 拆下螺栓 (2) 和将机油供油管和机油排油管固定到位的卡箍。
Show/hide table
图 1 | g00537468 |
- 拆下将机油供油管固定到涡轮增压器上的两根螺栓 (1) 。 拆下将机油排油管固定到涡轮增压器上的两根螺栓 (3) 。
- 在 3304B 上,松开两个软管卡箍,然后将软管从涡轮增压器上拆下。 使软管套在连接至缸盖的管子上。
- 松开螺母 (4) ,然后从发动机上拆下机油供油管。
- 松开将涡轮增压器 (5) 固定到排气歧管上的四根螺栓 (6) 和螺母。 从排气歧管上拆下涡轮增压器 (5) 和密封垫。 从发动机上拆下排油管 (7) ,然后检查 O 形密封圈有无损坏。 如果 O 形密封圈磨损或损坏,则应使用新零件更换。
Show/hide table
图 2 | g00537495 |
Caterpillar Information System:
G3500 Engines Engine Oil and Water Pump Drive - Disassemble
G3606 and G3608 Engines Air Inlet Choke - Assemble
G3606 and G3608 Engines Air Inlet Choke - Disassemble
G3606 and G3608 Engines Air Inlet Choke - Remove
G3500 Engines Engine Oil and Water Pump Drive - Assemble
3406E and 3456 Generator Set Engines Exhaust Manifold
G3500 Engines Engine Air Cleaner Service Indicator - Inspect
G3500 Engines Engine Oil Pan - Assemble
G3606 and G3608 Engines Aftercooler - Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
G3606 and G3608 Engines Aftercooler - Remove
3406E and 3456 Generator Set Engines Electrical Ground Stud
3406E Generator Set Engines Refill Capacities
3406E and 3456 Generator Set Engines Electric Starting Motor
3304B and 3306B Engines for Caterpillar Built Machines Turbocharger - Install
3116 Truck Engine Cold Weather Operation
3406E Generator Set Engines Control Panel
G3606 and G3608 Engines Gas Needle Valve - Remove and Install
3500 Engines for Caterpillar Built Generator Sets Engine Oil Cooler Bypass and Cooling Jet Sequence Valves
G3606 and G3608 Engines Magneto Interface - Remove and Install
G3606 and G3608 Engines Prechamber Check Valve - Remove and Install
Installation of 185-7733 Sensor Kit {1928} Installation of 185-7733 Sensor Kit {1928}
3500B Engines Turbocharger
G3606 and G3608 Engines Connecting Rod Bearings - Remove and Install