PRODUCT SUPPORT PROGRAM FOR REPLACING THE ADJUSTMENT SCREW ON CERTAIN B35 HYDRAULIC HAMMERS Caterpillar

PRODUCT SUPPORT PROGRAM FOR REPLACING THE ADJUSTMENT SCREW ON CERTAIN B35 HYDRAULIC HAMMERS

Usage:

TEBE0791-00

Show/hide table

07Mar2014

D-120

Show/hide table

*Before/After*	PRODUCT SUPPORT PROGRAM FOR REPLACING THE ADJUSTMENT SCREW ON CERTAIN B35 HYDRAULIC HAMMERS
6333		PS44212

Show/hide table

NOTE:

This Program must be administered either before or after failure. In either case the decision whether to apply the Program is made by the dealer. When reporting the repair, use "PS44212" as the Part Number and "7755" as the Group Number. If administered before failure, use "56" as the Warranty Claim Description Code and "T" as the SIMS Description code. If administered after failure, use "96" as the Warranty Claim Description Code, and "Z" as the SIMS Description Code.

Show/hide table

NOTE:

The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst.

Show/hide table

TERMINATION DATE

31Mar2016

PROBLEM

Show/hide table

The existing adjustment screw on the valve block on certain B35 Hydraulic Hammers allows the hammer to operate at a pressure that is above specification. If the adjustment screw is not replaced, damage to the hammer and the machine may occur.

AFFECTED PRODUCT

Show/hide table

Model	Identification Number
B35	MXE00100-00125, 127-158, 163

PARTS NEEDED

Show/hide table

Qty	Part Number	Description
1	3703883	KIT-SEAL (VALVE)
1	4467657	PLUG-PORT
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 23% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer.

ACTION REQUIRED

Show/hide table

Refer to the attached Rework Procedure.

Show/hide table

SERVICE CLAIM ALLOWANCES

Show/hide table

Product smu/age whichever comes first	Caterpillar		Dealer Suggested		Customer Suggested
Product smu/age whichever comes first	Parts %	Labor Hrs%	Parts %	Labor Hrs%	Parts %	Labor Hrs%
0-10000 hrs, 0-48 mo	100.0%	100.0%	0.0%	0.0%	0.0%	0.0%

Show/hide table

NOTE: This is a 3.0-hour job

Show/hide table

PARTS DISPOSITION

Show/hide table

Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.

Rework Procedure

Show/hide table

Perform all steps necessary to prepare the machine and the hammer for safely replacing the adjustment screw.

Work must be completed with hammer in the horizontal position. Clean the area around the valve block thoroughly in order to minimize contamination.

Adjustment screw, O-Ring and Backup Ring will be replaced.

Adjustment Screw Location:

Image1.1.1

Image1.1.2

Step 1 ? Use a 34mm wrench to loosen the lock nut.
Step 2 ? Use a 12mm hex key to remove the adjustment screw.
Step 3 ? Install O-Ring seal and backup ring onto 446-7657 Plug Port.
Note: O- Ring and Backup Ring are part of 370-3883 Seal Kit.

Image1.2.1

Image1.2.2

Step 4 ? Apply 4C-4030 Adhesive to the threads of 446-7657 Plug Port.
Step 5 ? Install 446-7657 Plug Port into the valve block of the hammer using 34mm wrench.

Image1.3.1

Machine Calibration Procedure

Perform all steps necessary to prepare the machine and the hammer for safely calibrating the machine. Refer to the Operation and Maintenance Manual (OMM) for your specific machine OMM) for the proper safety procedures.

Before the hammer can be returned to service, the auxiliary lines kit for the machine must be calibrated to ensure the correct flow and pressure is being delivered to the hammer.

Failure to complete this procedure can result in higher owning and operating costs as well as damage to the hammer or the machine.

All testing must be done with the hydraulic oil of the machine at operating temperature ? 50C.

Image1.7.1

1. Verify the setting of the 375-5727 auxiliary circuit pressure relief valve. The valve should be set to 240 - 250 bar.
a. With the hammer installed, close the return side ball valve on the machine.
b. Install a pressure gauge capable of reading pressure above 250 bar.
c. Active the auxiliary circuit and record the pressure shown on the gauge.
i. If the relief pressure is above 250 bar, loosen the jam nut and turn the adjustment screw counter-clockwise to reduce the opening pressure for the relief valve. Tighten the jam nut if the relief pressure is below 240 - 250 bar, loosen the jam nut and turn the adjustment screw clockwise to increase the opening pressure for the relief valve. Tighten the jam nut.
d. Repeat Step 1c to retest the relieve valve pressure to verify that the valve is set to 240 - 250 bar.
e. Remove the pressure gauge and open the return side ball valve.

Image1.8.1

2. Install a flow meter onto the machine auxiliary circuit. Operate the auxiliary circuit of the machine and record the flow when the flow meter reads 170 Bar. The flow should be 190 Liters per minute (Lpm) at 170 Bar. Flow is adjusted by the 1U-1100 Valve
a. If the flow is greater than 190 Lpm at 170 Bar, loosen the jam nut and turn the adjustment screw counter- clockwise to reduce the pilot pressure to the valve spool. Tighten the jam nut.
b. If the flow is less than 190 Lpm at 170 Bar, loosen the jam nut and turn the adjustment screw clockwise to increase the pilot pressure to the valve spool. Tighten the jam nut.
c. Repeat Step 2 in order to retest the flow to the auxiliary circuit.
d. Disconnect the flow meter and reinstall the hammer onto the auxiliary circuit of the machine.