Crankshaft - Install
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将销 (5) 安装到曲轴中。
定位销突出曲轴表面的最大长度 ... 6.4 mm (0.25 in)
Show/hide table
图 1 | g01018180 |
Show/hide table
图 2 | g01029696 |
- 将定位销 (6) 安装到曲轴中。
定位销 (6) 突出曲轴表面的长度 ... 4.1 ± 0.5 mm (0.16 ± 0.02 in)
- 加热曲轴齿轮 (4) 。 将曲轴齿轮 (4) 安装到曲轴上,键槽对准定位销 (6) 。 定时标记 "V" 应背对曲轴。
注: 切勿将曲轴齿轮 (4) 加热到 205 °C (400 °F) 以上。
- 将主轴承的上轴瓦安装到缸体中。
注: 检查完间隙后,安装主轴承并保持其干燥。 请参阅拆解与组装, "轴承间隙 – 检查"。 在主轴承上涂抹清洁的发动机机油,以便于最终组装。
- 将合适的起吊设备连接到曲轴 (3) 。 曲轴 (3) 的重量约为 159 kg (350 lb)。 安装曲轴 (3) ,对齐曲轴齿轮上的标记 "V" 与齿轮组上的标记 "V"。
- 安装连杆盖。
- 将主轴承盖 (1) 放到位。 安装主轴承盖的螺栓 (2) 。
Show/hide table
图 3 | g01029693 |
End By:
- 安装飞轮壳体。 请参阅 拆解和组装, "飞轮壳体 - 拆卸和安装"。
- 安装前壳体。 请参阅 拆解和组装, "壳体(前) - 安装"。
Caterpillar Information System:
G3300 Engines Engine Oil and Filter - Change
G3300 Engines Engine Oil Sample - Obtain
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Install
3606 and 3608 Engines Camshaft
G3300 Engines Engine Oil Level - Check
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Remove
3406C (PEEC III) Truck Engine Electric Starting Motor
3608 Engine Governor Drive
3176C and 3196 Engines For Caterpillar Built Machines Gear Group (Front) - Install
3176C and 3196 Engines For Caterpillar Built Machines Gear Group (Front) - Remove
3176C and 3196 Engines For Caterpillar Built Machines Front Cover - Install
3176C and 3196 Engines For Caterpillar Built Machines Front Cover - Remove
3176C and 3196 Engines For Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
3406E On-Highway Engine Flywheel - Remove
3306B Industrial Engine Service Meter - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Valve Mechanism Cover Base - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
3406E On-Highway Engine Flywheel - Install
3176C and 3196 Engines For Caterpillar Built Machines Rocker Shaft and Pushrod - Install
3306B Industrial Engine Tachometer Drive - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Lifter Group - Remove and Install
3406E On-Highway Engine Crankshaft Rear Seal - Remove
3304B and 3306B Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
3406E and 3456 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install