Vibration Damper and Pulley - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | FT-0915     | 接头     | 1     |
0S-1590 | 螺栓     | 6     | |
5F-7342 | 接头     | 2     | |
5F-7369 | 拉拔器腿     | 2     | |
3H-0465 | 压拉器垫板     | 4     | |
1B-4207 | 全高螺母     | 2     | |
8B-7560 | 垫板     | 1     | |
1P-0820 | 液压拉拔器     | 1     | |
4C-4865 | 手动液压泵     | 1     |
开始:
- 释放驱动皮带张力,然后拆下驱动皮带。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 从曲轴上拆下螺栓 (1) 和垫圈 (2) 。 将隔套 (4) 安装到螺栓 (1) 上。 增加隔套,以便达到垫圈 (2) 和减振器 (3) 之间约 3.18 mm (0.125 in) 的间隙。 安装螺栓 (1) 、垫圈 (2) 和隔套 (4) 。
Show/hide table
图 1 | g00515722 |
- 如图所示,安装工具 (A) 。 从曲轴上松开减振器 (9) 。
Show/hide table
图 2 | g00515749 |
- 从曲轴上拆下工具 (A) 、螺栓 (1) 、垫圈 (2) 、隔套 (4) 和减振器 (3) 。
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 检查减振器有无泄漏和凹痕。 如果出现任一种情况,用新零件更换减振器。
- 将减振器 (1) 在曲轴上放置到位,然后安装垫圈 (2) 和螺栓 (3) 。
注: 安装时,垫圈 (2) 的平面侧必须朝向减振器 (1) 。
Show/hide table
图 3 | g00515758 |
- 将螺栓 (3) 拧紧至扭矩 284 至 340 N·m (210 至 250 lb ft)。 用锤子敲击螺栓 (3) ,然后再次将螺栓拧紧至扭矩 284 至 340 N·m (210 至 250 lb ft)。
End By: 安装驱动皮带并施加正确的张紧力。
Caterpillar Information System:
3406E On-Highway Engine Crankshaft Rear Seal - Remove
3176C and 3196 Engines For Caterpillar Built Machines Lifter Group - Remove and Install
3306B Industrial Engine Tachometer Drive - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Rocker Shaft and Pushrod - Install
3406E On-Highway Engine Flywheel - Install
3176C and 3196 Engines For Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
3176C and 3196 Engines For Caterpillar Built Machines Valve Mechanism Cover Base - Remove and Install
3306B Industrial Engine Service Meter - Remove and Install
3406E On-Highway Engine Flywheel - Remove
3176C and 3196 Engines For Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
3406E On-Highway Engine Crankshaft - Install
G3300 Engines Engine Oil and Filter - Change
3406E and 3456 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
3176C and 3196 Engines For Caterpillar Built Machines Water Outlet Manifold - Remove
3176C and 3196 Engines For Caterpillar Built Machines Water Outlet Manifold - Install
3176C and 3196 Engines For Caterpillar Built Machines Inlet Manifold - Remove
3176C and 3196 Engines For Caterpillar Built Machines Inlet Manifold - Install
3406E On-Highway Engine Gear Group (Front) - Remove
3406E On-Highway Engine Engine Oil Pan - Remove and Install
3612 and 3616 Engines Manual Valve Group (Cylinder Pressure)
3116 and 3126 Marine Engines Refill Capacities
G3300 Engines Engine Crankcase Breather - Clean
3116 and 3126 Marine Engines Reference Material
3612 and 3616 Engines Compression Release Valve