Lifter Group - Remove and Install
开始:
- 拆卸缸盖。 请参阅拆解和组装, "缸盖 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 拆下螺栓 (1) 和挺杆组件 (2)。 挺杆组件可以分两节拆除。
Show/hide table
图 2 g01022187 - 从挺杆轴 (5) 右端拆除下列项:托架组件 (6), 气门挺杆 (8) 和 单体喷油器挺杆 (9)。
- 从挺杆轴 (5) 中部拆除下列项:气门挺杆 (8) 和 单体喷油器挺杆 (9)。
- 从挺杆轴 (5) 左端拆除下列项:托架组件 (7), 气门挺杆 (8) 和 单体喷油器挺杆 (9)。
- 从挺杆轴 (5) 上拆除定位销 (4) 和盖螺塞 (3)。
- 必要时将弹簧销从托架组件 (7) 上拆除。
- 必要时,将定位销 (10) 从托架组件 (6) 上拆下。
Show/hide table
图 1 | g01022184 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将弹簧销和定位销 (10) 安装在托架组件 (6) 中。 将弹簧销和定位销安装在托架组件 (7) 中。
- 将定位销 (4) 和盖螺塞 (3) 安装在挺杆轴 (5) 中。 组装前用清洁的发动机机油润滑挺杆轴。
- 将下列项安装在挺杆轴 (5) 左端:托架组件 (7), 气门挺杆 (8) 和 单体喷油器挺杆 (9)。
- 将下列项安装在挺杆轴 (5) 中间:气门挺杆 (8) 和 单体喷油器挺杆 (9)。
- 将下列项安装在挺杆轴 (5) 左端:托架组件 (6), 气门挺杆 (8) 和 单体喷油器挺杆 (9)。
Show/hide table
图 4 g01022184 注: 所有挺杆组件在被安装到发动机上之前,要在先浸入到清洁的发动机油中。
- 将挺杆组件 (2) 定位到发动机上并安装螺栓 (1)。 拧紧螺栓至扭矩为
30 ± 3 N·m (22 ± 2 lb ft) 。
Show/hide table
图 3 | g01022187 |
结束:
- 安装缸盖。 请参阅拆解和组装, "缸盖 - 安装"。
Caterpillar Information System:
3306B Industrial Engine Tachometer Drive - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Rocker Shaft and Pushrod - Install
3406E On-Highway Engine Flywheel - Install
3176C and 3196 Engines For Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
3176C and 3196 Engines For Caterpillar Built Machines Valve Mechanism Cover Base - Remove and Install
3306B Industrial Engine Service Meter - Remove and Install
3406E On-Highway Engine Flywheel - Remove
3176C and 3196 Engines For Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
3406E On-Highway Engine Crankshaft - Install
G3300 Engines Engine Oil and Filter - Change
G3300 Engines Engine Oil Sample - Obtain
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Install
3406E On-Highway Engine Crankshaft Rear Seal - Remove
3304B and 3306B Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
3406E and 3456 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
3176C and 3196 Engines For Caterpillar Built Machines Water Outlet Manifold - Remove
3176C and 3196 Engines For Caterpillar Built Machines Water Outlet Manifold - Install
3176C and 3196 Engines For Caterpillar Built Machines Inlet Manifold - Remove
3176C and 3196 Engines For Caterpillar Built Machines Inlet Manifold - Install
3406E On-Highway Engine Gear Group (Front) - Remove
3406E On-Highway Engine Engine Oil Pan - Remove and Install
3612 and 3616 Engines Manual Valve Group (Cylinder Pressure)
3116 and 3126 Marine Engines Refill Capacities
G3300 Engines Engine Crankcase Breather - Clean