Flywheel - Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 138-7573 | Lifting Bracket | 2 |
B | FT2712 | Guide Stud | 2 |
C | 4C-5593 | Anti-Seize Compound | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Raise the temperature of ring gear (3). Install ring gear (3) on flywheel (2).
Show/hide table
Illustration 2 g01018439 - Install Tooling (B).
- Fasten a suitable lifting device to flywheel (2). Use Tooling (A) to install flywheel (2) on Tooling (B).
- Apply Tooling (C) to bolts (1) that hold the flywheel to the crankshaft. Tighten bolts (1) to a torque of
270 ± 40 N·m (200 ± 30 lb ft) . - Remove Tooling (A) and Tooling (B).
- Install remaining bolts (1). Apply Tooling (C) to bolts (1) that hold the flywheel to the crankshaft. Tighten bolts (1) to a torque of
270 ± 40 N·m (200 ± 30 lb ft) . - Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect" and Testing and Adjusting, "Flywheel Housing - Inspect".
Show/hide table
Illustration 1 | g01018440 |
Show/hide table
NOTICE |
---|
The ring gear must be installed with the chamfered side of the teeth upward. The chamfered side of the gear teeth will be facing toward the starter motor when the flywheel is installed so that the starter motor will engage correctly. |
Caterpillar Information System:
3176C and 3196 Engines For Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
3176C and 3196 Engines For Caterpillar Built Machines Valve Mechanism Cover Base - Remove and Install
3306B Industrial Engine Service Meter - Remove and Install
3406E On-Highway Engine Flywheel - Remove
3176C and 3196 Engines For Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
3406E On-Highway Engine Crankshaft - Install
G3300 Engines Engine Oil and Filter - Change
G3300 Engines Engine Oil Sample - Obtain
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Install
3606 and 3608 Engines Camshaft
G3300 Engines Engine Oil Level - Check
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Remove
3176C and 3196 Engines For Caterpillar Built Machines Rocker Shaft and Pushrod - Install
3306B Industrial Engine Tachometer Drive - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Lifter Group - Remove and Install
3406E On-Highway Engine Crankshaft Rear Seal - Remove
3304B and 3306B Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
3406E and 3456 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
3176C and 3196 Engines For Caterpillar Built Machines Water Outlet Manifold - Remove
3176C and 3196 Engines For Caterpillar Built Machines Water Outlet Manifold - Install
3176C and 3196 Engines For Caterpillar Built Machines Inlet Manifold - Remove
3176C and 3196 Engines For Caterpillar Built Machines Inlet Manifold - Install
3406E On-Highway Engine Gear Group (Front) - Remove
3406E On-Highway Engine Engine Oil Pan - Remove and Install