Camshaft
Show/hide table
图 1 | g00515083 |
(1) 凸轮轴轴颈的直径 ... 173.80 ± 0.03 mm (6.843 ± 0.001 in)
安装后凸轮轴轴承孔 ... 174.00 ± 0.05 mm (6.850 ± 0.002 in)
(2) 新隔板的厚度 ... 11.80 ± 0.05 mm (0.465 ± 0.002 in)
(3) 正时螺栓的定位位置
Show/hide table
图 2 | g00289768 |
凸轮轴轴颈上定位销的位置 |
Show/hide table
图 3 | g00469453 |
凸轮轴轴颈上定位销的位置 |
Show/hide table
注意 |
---|
在组装时应遵守正确的凸轮段关系(正时)。 如果凸轮段不合拍,将发生严重的发动机损坏。 |
注: 与可变定位销相关的单个定位销的位置取决于凸轮轴轴颈的指定字符。 单个定位销和定位槽在同一端。 可变定位销和定位槽在同一端。
(5) 定位槽
(6) 单个定位销的位置面向凸轮轴轴承轴颈
- 从定位销顶面到凸轮轴轴颈之间的距离 ... 7.0 ± 0.5 mm (0.28 ± 0.02 in)
(7) 可变定位销的位置面向凸轮轴轴承轴颈
- 从定位销顶面到凸轮轴轴颈之间的距离 ... 7.0 ± 0.5 mm (0.28 ± 0.02 in)
Show/hide table
图 4 | g00289771 |
3606 凸轮轴轴颈的指定字符 |
Show/hide table
图 5 | g00469407 |
3608 凸轮轴轴颈的指定字符 |
(8) 凸轮轴轴承轴颈
安装凸轮轴轴承轴颈,使槽端朝向发动机的前端。
(9) 凸轮轴块
安装凸轮轴块,使槽面法兰朝向标准旋转发动机的后端。 安装凸轮轴块,使槽面法兰朝向反向旋转发动机的前端。
(10) 拧紧凸轮轴块的螺栓至以下扭矩。 ... 270 ± 40 N·m (200 ± 30 lb ft)
(11) 必须将凸轮轴组装到装配夹具或缸体中。
- 在凸轮轴 (11) 的后端施加压力。 3606 的滚动扭矩必须是以下的最大值。 ... 22 N·m (16
lb ft)
- 在凸轮轴 (11) 的后端施加压力。 3608 的滚动扭矩必须是以下的最大值。 ... 28 N·m (21 lb ft)
Show/hide table
图 6 | g00289772 |
(12) 规定的凸轮轴凸轮升程
为了找到规定的凸轮轴凸轮升程,请使用以下步骤:
- 测量凸轮轴 (13) 的总高度。
- 测量基圆 (14) 。
- 从凸轮轴 (13) 的总高度中减去基圆 (14) 。 所得的差就是规定的凸轮轴凸轮升程 (12) 。
- 凸轮轴的规定凸轮轴凸轮升程 (12) 值如下:
排气凸轮 ... 19.500 mm (0.7677 in)
进气凸轮 ... 19.500 mm (0.7677 in)
喷油泵凸轮 ... 21.473 mm (0.8454 in)
Caterpillar Information System:
G3300 Engines Engine Oil Level - Check
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Remove
3406C (PEEC III) Truck Engine Electric Starting Motor
3608 Engine Governor Drive
3176C and 3196 Engines For Caterpillar Built Machines Gear Group (Front) - Install
3176C and 3196 Engines For Caterpillar Built Machines Gear Group (Front) - Remove
3176C and 3196 Engines For Caterpillar Built Machines Front Cover - Install
3176C and 3196 Engines For Caterpillar Built Machines Front Cover - Remove
3406E On-Highway Engine Crankshaft - Remove
3406E On-Highway Engine Engine Oil Pump - Disassemble
3304B and 3306B Engines for Caterpillar Built Machines Water Pump - Install
G3500B Engines Reference Material
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Install
G3300 Engines Engine Oil Sample - Obtain
G3300 Engines Engine Oil and Filter - Change
3406E On-Highway Engine Crankshaft - Install
3176C and 3196 Engines For Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
3406E On-Highway Engine Flywheel - Remove
3306B Industrial Engine Service Meter - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Valve Mechanism Cover Base - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
3406E On-Highway Engine Flywheel - Install
3176C and 3196 Engines For Caterpillar Built Machines Rocker Shaft and Pushrod - Install
3306B Industrial Engine Tachometer Drive - Remove and Install