Front Cover - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 9S-3263     | 螺纹锁固胶     | -     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 检验壳体罩盖密封垫的状况。 必要时,更换密封垫。
注: 盖的后表面和壳体的前表面必须清洁。
- 安装壳体盖密封垫 (5) 。
Show/hide table
图 1 | g01021415 |
- 将以下各项安装到前壳体上:前盖 (4螺栓), (2螺栓), (3) 和 垫圈。
注: 不要重复使用密封件垫圈。 安装时使用新密封垫圈。
注: 螺栓 (3) 是贯穿螺栓。 安装之前先在螺纹上涂抹工具 (A) 。
- 用新密封垫圈和螺母安装螺柱 (1) 。
End By:
- 安装燃油输油泵。 请参阅 拆解和组装, "燃油输油泵 - 安装"。
- 安装曲轴前油封。 请参阅 拆解和组装, "曲轴前密封 - 安装"。
- 安装皮带张紧装置。 请参阅 拆解和组装皮带, "张紧装置 - 拆卸和安装"。
- 安装交流发电机。 请参阅 拆解和组装, "交流发电机 - 拆卸和安装"。
Caterpillar Information System:
3176C and 3196 Engines For Caterpillar Built Machines Front Cover - Remove
3406E On-Highway Engine Crankshaft - Remove
3406E On-Highway Engine Engine Oil Pump - Disassemble
3304B and 3306B Engines for Caterpillar Built Machines Water Pump - Install
G3500B Engines Reference Material
3608 Engine Engine Design
3600 Heavy Fuel Engines Exhaust Piping - Inspect
3304B and 3306B Engines for Caterpillar Built Machines Water Pump - Remove
3406E On-Highway Engine Engine Oil Filter Base - Disassemble
G3500B Engines Refill Capacities and Recommendations
3176C and 3196 Industrial Engines Inlet Manifold - Install
3406E On-Highway Engine Inlet and Exhaust Valve Seat Inserts - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Gear Group (Front) - Remove
3176C and 3196 Engines For Caterpillar Built Machines Gear Group (Front) - Install
3608 Engine Governor Drive
3406C (PEEC III) Truck Engine Electric Starting Motor
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Remove
G3300 Engines Engine Oil Level - Check
3606 and 3608 Engines Camshaft
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Install
G3300 Engines Engine Oil Sample - Obtain
G3300 Engines Engine Oil and Filter - Change
3406E On-Highway Engine Crankshaft - Install
3176C and 3196 Engines For Caterpillar Built Machines Valve Mechanism Cover - Remove and Install