Gear Group (Front) - Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将附件驱动装置 (8) 安置到位并安装螺栓 (7)。 将螺栓拧紧至扭矩
100 ± 20 N·m (74 ± 15 lb ft) 。 - 将以下各项安装到前壳体上:齿轮 (6), 轴承和轴 (5) 和 螺栓 (4)。 将螺栓拧紧至扭矩为
240 ± 40 N·m (177 ± 30 lb ft) 。 - 将以下各项安装到前壳体上:齿轮 (3), 轴承和轴 (2) 和 螺栓 (1)。 将螺栓拧紧至扭矩为
240 ± 40 N·m (177 ± 30 lb ft) 。注: 确保齿轮上的正时标记对齐。
Show/hide table
图 1 | g01021531 |
结束:
- 安装曲轴位置传感器。 请参阅拆解和组装, "曲轴位置传感器 - 拆卸和安装"。
- 安装凸轮轴。 请参阅拆解和组装, "凸轮轴 - 安装"。
- 安装凸轮轴位置传感器。 请参阅拆解和组装, "凸轮轴位置传感器 - 拆卸和安装"。
- 安装交流发电机。 请参阅拆解和组装, "交流发电机 - 拆卸和安装"。
- 安装发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 安装"。
- 安装水泵。 请参阅拆解和组装, "水泵 - 安装"。
Caterpillar Information System:
3176C and 3196 Engines For Caterpillar Built Machines Gear Group (Front) - Remove
3176C and 3196 Engines For Caterpillar Built Machines Front Cover - Install
3176C and 3196 Engines For Caterpillar Built Machines Front Cover - Remove
3406E On-Highway Engine Crankshaft - Remove
3406E On-Highway Engine Engine Oil Pump - Disassemble
3304B and 3306B Engines for Caterpillar Built Machines Water Pump - Install
G3500B Engines Reference Material
3608 Engine Engine Design
3600 Heavy Fuel Engines Exhaust Piping - Inspect
3304B and 3306B Engines for Caterpillar Built Machines Water Pump - Remove
3406E On-Highway Engine Engine Oil Filter Base - Disassemble
G3500B Engines Refill Capacities and Recommendations
3608 Engine Governor Drive
3406C (PEEC III) Truck Engine Electric Starting Motor
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Remove
G3300 Engines Engine Oil Level - Check
3606 and 3608 Engines Camshaft
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Install
G3300 Engines Engine Oil Sample - Obtain
G3300 Engines Engine Oil and Filter - Change
3406E On-Highway Engine Crankshaft - Install
3176C and 3196 Engines For Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
3406E On-Highway Engine Flywheel - Remove
3306B Industrial Engine Service Meter - Remove and Install