950M, 962M, 966M, 972M, 980M, and 982M Wheel Loaders Information Display Caterpillar

Illustration 1	g06220403
(1) SERVICE button

Press the SERVICE button (1) that is located on the right side of the Information Display. The Service menu list page will appear.

Illustration 2	g06220427
Service menu list page (2) Service menu button group (3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button

The Service menu list page contains the following menu buttons:

• Diagnostics

• Configurations

• Calibrations

• ECM Summary

• Service Mode

Diagnostics

Service > Diagnostics > Events and Details

Illustration 3	g06220435
An example of the Events data page is shown on the right hand side. No active or logged Diagnostic Events are listed. (3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (9) Diagnostics menu button (10) Double DOWN Arrow button (11) Double UP Arrow button

1. Press the SERVICE button (1) located on the right side of the Display. The Service menu button page will appear.

2. Press the Diagnostics menu button (9). The button will turn first to blue, then turn to yellow. The Diagnostics data page will appear.
   Show/hide table

   Illustration 4	g06220469
   (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (10) Double DOWN Arrow button (11) Double UP Arrow button

3. Navigate by pressing the UP Arrow button (4) or the DOWN Arrow button (6) on the right side of the Information Display. The selected event will be highlighted with a yellow strip.

4. Press the DOUBLE DOWN Arrow button (10) to scroll to the bottom of the list.

5. Press the DOUBLE UP Arrow button (11) to scroll to the top of the list.

6. To view the Event, press the OK button (5) when an Event is highlighted with a yellow strip. The Events Details page will appear with additional information.

7. Press the BACK button (7) to return to the previous menu.

8. Press the HOME button (8) to return to the Home page (Performance page).

Configurations

Service > Configurations

Note: The Configurations menu items will show when the Service Mode is enabled.

For more information, refer to the following section in this manual:

• Service > Service Mode

Illustration 5	g06220551
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (12) Configurations menu button

1. Press the Service button (1) that is located on the right side of the Information Display. The Service menu page will appear.

2. Press the Configurations menu button (12). The button will turn first to blue, then turn to yellow. The Configurations menu page will appear.

Note: Some Configurations will not appear in Medium Wheel Loader (MWL) menus. Show or hide conditions will depend upon the MWL model and its equipped features.

Illustration 6	g06220572
Configurations menu list page (3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (13) Configurations menu button group

The Configurations menu list page contains the following menu buttons:

• Implement

• Machine

• Engine

• Payload

• Trans (Transmission) Oil Type (Only on select machine models)

Configuration Menus

Implement Configurations

Service > Configurations > Implement

Note: The Service Mode must be enabled.

Illustration 7	g06220577
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (14) Implement menu button

Press the Implement menu button (14). The button will first turn to blue, then turn to yellow. The Implement menu page appears.

Illustration 8	g06220578
(4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (15) Implement menu button group

The Implement menu list page contains the following menu buttons:

• Raise Kickout (Enabled or Disabled)

• Lower Kickout (Enabled or Disabled)

• Rackback Kickout (Enabled or Disabled)

• Dump Kickout (Enabled or Disabled)

Press the intended menu button in the menu button group (15). Each subpage will allow the operator to select between Enabled and Disabled.

Illustration 9	g06220597
(7) BACK button (8) HOME button (16) Enabled menu button (17) Disabled menu button

Press the intended menu button (Enabled - (16) or Disabled - (17)). The menu button will first turn to blue, then turn to yellow. The selected menu button will also be marked by a black check mark.

Press the BACK button (7) to return to the previous menu.

Press the HOME button (8) to return to the Home page (Performance page).

Machine Configurations

Service > Configurations > Machine

Illustration 10	g06220620
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (18) Machine menu button

Press the Machine menu button (18). The button will first turn to blue, then turn to yellow. The Machine menu page will appear.

Illustration 11	g06220867
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (19) Machine Menu button group

The Machine menu list page contains the following menu buttons:

• Auto Rear Wiper (Menu buttons: Enabled or Disabled)

• Autolube (This feature must be installed)

• Beacon (Menu buttons: Installed or Not Installed) (The Service Mode must be enabled)

• LR (Long Range) Work Lights (Menu buttons: Installed or Not Installed) (The Service Mode must be enabled)

• Speed Limit (Machine Models: PS) (XE machines) (The Service Mode must be enabled)

Service > Configurations > Machine > Auto Rear Wiper

Illustration 12	g06220871
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (20) Auto Rear Wiper button

Press the intended menu button in the menu button group (19). Each subpage will allow the operator to select between the Enabled or Disabled menu buttons.

Illustration 13	g06220876
(7) BACK button (8) HOME button (21) Enabled menu button (22) Disabled menu button

Press the intended menu button (Enabled - (21) or Disabled - (22)). The menu button will first turn to blue, then turn to yellow. The selected menu button will also be marked by a black check mark.

Press the BACK button (7) to return to the previous menu.

Press the HOME button (8) to return to the Home page (Performance page).

Service > Configurations > Machine > Autolube

Illustration 14	g06220884
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (23) Autolube menu button

Press the Autolube menu button (23). The button will first turn to blue, then turn to yellow. The Autolube settings page will appear.

Illustration 15	g06220890
Autolube settings page (7) BACK button (8) HOME button (24) Autolube Mode button (AUTO) (25) Autolube Mode button (Single Test) (26) Autolube Mode button (Continuous Test) (27) Cycle Frequency Sliding Indicator (28) Cycle Frequency Yellow UP Arrow button (29) Cycle Frequency Yellow DOWN Arrow button

There are three Autolube Mode settings:

• AUTO

• Single Test

• Continuous Test

Press the intended Autolube Mode button. A green button indicates that the indicated Autolube Mode has been set.

A gray button indicates that the Autolube Mode has not been set.

There are three Cycle Frequency mode settings:

• High

• Medium

• Low

Press either the Yellow UP Arrow button or the Yellow DOWN Arrow button to select the intended Cycle Frequency mode setting. The Sliding Indicator will move to the intended selection. The intended selection is indicated by bold text.

Illustration 16	g06220920
(7) BACK button (8) HOME button (27) Cycle Frequency Sliding Indicator (28) Cycle Frequency Yellow UP Arrow button (29) Cycle Frequency Yellow DOWN Arrow button

Note: When the Menu Sliding Indicator is at the top (Low) or the bottom (High), the corresponding yellow arrow button will not be visible.

Press the BACK button (7) to return to the previous menu.

Press the HOME button (8) to return to the Home page (Performance page).

Service > Configurations > Machine > Beacon

Note: The Service Mode must be enabled.

Illustration 17	g06220923
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (30) Beacon menu button

Press the Beacon menu button (30). The button will first turn to blue, then turn to yellow. The Beacon settings page will appear.

Illustration 18	g06220935
(7) BACK button (8) HOME button (31) Installed menu button (32) Not Installed menu button

Press the intended menu button (Installed - (31) or Not Installed - (32)). The menu button will first turn to blue, then turn to yellow. The selected menu button will also be marked by a black check mark.

Press the BACK button (7) to return to the previous menu.

Press the HOME button (8) to return to the Home page (Performance page).

Service > Configurations > Machine > LR Work Lights

Note: The Service Mode must be enabled.

Illustration 19	g06220947
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (33) LR Work Lights menu button

Press the LR Work Lights menu button (33). The button will first turn to blue, then turn to yellow. The LR Work Lights settings page will appear.

Illustration 20	g06221837
(4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (34) Installed menu button (35) Not Installed menu button

Press the intended menu button (Installed - (34) or Not Installed - (35)). The menu button will first turn to blue, then turn to yellow. The selected menu button will also be marked by a black check mark.

Press the BACK button (7) to return to the previous menu.

Press the HOME button (8) to return to the Home page (Performance page).

Service > Configurations > Machine > Speed Limit

Note: The Service Mode must be enabled.

Illustration 21	g06221850
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (36) Speed Limit menu button

Illustration 22	g06221865
Speed Limit settings page (7) BACK button (8) HOME button (37) Increment/Decrement bar (Forward) (38) Increment/Decrement bar (Reverse)

1. Press the Service button (1) that is located on the right side of the Information Display. The Service page will appear.

2. Press the Configurations menu button (12). The button will turn first to blue, then turn to yellow. The Configurations menu page will appear.

3. Press the Machine menu button (18). The button will turn first to blue, then turn to yellow. The Machine menu page will appear.

4. Press the Speed Limit menu button (36). The button will turn first to blue, then turn to yellow. The Speed Limit settings page will appear.

5. To set the Machine Max (Maximum) Speed forward, press either the PLUS (+) Arrow button or the MINUS (-) Arrow button on the Forward Increment/Decrement Bar (37).

6. To set the Machine Max (Maximum) Speed to reverse, press either the PLUS (+) Arrow button or the MINUS (-) Arrow button on the Reverse Increment/Decrement Bar (38).

7. Press the BACK button (7) to return to the previous menu.

8. Press the HOME button (8) to return to the Home page.

Engine Configurations

Service > Configurations > Engine

Note: The Service Mode must be enabled.

Illustration 23	g06221901
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (39) Engine menu button

Press the Engine menu button (39). The button will first turn to blue, then turn to yellow. The Engine menu page will appear.

Illustration 24	g06228847
(7) BACK button (8) HOME button (40) Engine menu button group

The Engine menu list page contains the following menu buttons:

• Engine Idle Timer (Enabled or Disabled)

• Engine Idle Delay (Enabled or Disabled)

• Inducement Override

Service > Configurations > Engine > Engine Idle Timer

Illustration 25	g06228851
(7) BACK button (8) HOME button (41) Engine Idle Timer menu button

Press the Engine Idle Timer menu button (41). The button will first turn to blue, then turn to yellow. The Engine Idle Timer settings page will appear.

Illustration 26	g06221936
(7) BACK button (8) HOME button (42) Enabled menu button (43) Disabled menu button

Press the intended menu button (Enabled - (42) or Disabled - (43)). The menu button will first turn to blue, then turn to yellow. The selected menu button will also be marked by a black check mark.

Press the BACK button (7) to return to the previous menu.

Press the HOME button (8) to return to the Home page (Performance page).

Service > Configurations > Engine > Engine Idle Delay

Illustration 27	g06228859
(7) BACK button (8) HOME button (44) Engine Idle Delay menu button

Press the Engine Idle Delay menu button (44). The button will first turn to blue, then turn to yellow. The Engine Idle Delay settings page will appear.

Illustration 28	g06221950
(7) BACK button (8) HOME button (45) Enabled menu button (46) Disabled menu button

Press the intended menu button (Enabled - (45) or Disabled - (46)). The menu button will first turn to blue, then turn to yellow. The selected menu button will also be marked by a black check mark.

Press the BACK button (7) to return to the previous menu.

Press the HOME button (8) to return to the Home page (Performance page).

Service > Configurations > Engine > Inducement Override

Note: This feature is only available on the following models:

• 950_M_PS_HRC

• 962_M_PS_HRC

• 966_M_PS_HRC

• 966_M_CVT_HRC

• 972_M_PS_HRC

• 972_M_CVT_HRC

• 980_M_PS_HRC

• 982_M_PS_HRC

Illustration 29	g06221960
(7) BACK button (8) HOME button (47) Inducement Override menu button

Press the Inducement Override menu button (47). The button will first turn to blue, then turn to yellow. The Inducement Override page will appear.

Illustration 30	g06221964

The page, Emergency Use Only See OMM, will show for ten (10) seconds.

Illustration 31	g06221969

The page, Penalties Apply for Misuse, will show for ten (10) seconds. Then, the Inducement Override menu page will appear.

Illustration 32	g06222005
Inducement Override menu page (5) OK button (48) Inactive menu button (49) Active menu button

Press the intended menu button. (Inactive - (48) or Active - (49)). The menu button will first turn to blue, then turn to yellow. The selected menu button will also be marked by a black check mark. Press the OK button (5) to continue. The Active Inducement Override page will appear.

Illustration 33	g06222013
Activate Inducement Override page (5) OK button (7) BACK button (8) HOME button

To activate the Inducement Override feature, press the OK button (5).

Press the BACK button (7) to return to the previous

menu.

Press the HOME button (8) to return to the Home

page (Performance page).

Payload Configurations

Service > Configurations > Payload

Note: The Service Mode must be enabled.

Note: The Cat^® Production Measurement feature must be installed.

Illustration 34	g06222017
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (50) Payload menu button

Press the Payload menu button (50). The button will first turn to blue, then turn to yellow. The Payload menu page will appear.

Illustration 35	g06222022
Payload menu list page (3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (51) Payload menu list page

The Payload menu list page contains the following menu buttons:

• Printer Installation VIMS (Must show Printer Installation (Legacy))

• Printer Installation (Must show Printer Installation (NM))

• Auto Truck ID (Cat^® Production Measurement must be installed)

• Auto Material ID (Cat^® Production Measurement must be installed)

• Scale Data Source (The Service Mode must be enabled)

• Cat^® Scale Demo (Demonstration)

• Cat^® Scale

Service > Configurations > Payload > Printer Installation

Note: The printer must be installed.

Illustration 36	g06222023
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (52) Printer Installation menu button

1. Press the Printer Installation menu button (52). The button will turn to blue, then turn to yellow. The Printer Installation menu page will appear.
   Show/hide table

   Illustration 37	g06222024
   Printer Installation menu page (7) BACK button (8) HOME button (53) Installed menu button (54) Not Installed menu button

2. Press the intended menu button (Installed - (53) or Not Installed - (54)). The menu button will first turn to blue, then turn to yellow. The selected menu button will also be marked by a black check mark.

Press the BACK button (7) to return to the previous menu.

Press the HOME button (8) to return to the Home page (Performance page).

Service > Configurations > Payload > Auto Truck ID

Note: The Cat^® Production Measurement feature must be installed.

Illustration 38	g06222032
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (55) Auto Truck ID menu button

1. Press the Auto Truck ID menu button (55). The button will turn to blue, then turn to yellow. The Auto Truck ID menu page will appear.
   Show/hide table

   Illustration 39	g06222041
   Auto Truck ID menu page (7) BACK button (8) HOME button (56) Enabled menu button (57) Disabled menu button

2. Press the intended menu button (Enabled - (56) or Disabled - (57)). The menu button will first turn to blue, then turn to yellow. The selected menu button will also be marked by a black check mark.

Press the BACK button (7) to return to the previous menu.

Press the HOME button (8) to return to the Home page (Performance page).

Service > Configurations > Payload > Auto Material ID

Note: The Cat^® Production Measurement feature must be installed.

Illustration 40	g06222047
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (58) Auto Material ID menu button

1. Press the Auto Material ID menu button (58). The button will turn to blue, then turn to yellow. The Auto Material ID menu page will appear.
   Show/hide table

   Illustration 41	g06222048
   Auto Material ID menu page (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (59) Enabled menu button (60) Disabled menu button

2. Press the intended menu button (Enabled - (59) or Disabled - (60)). The menu button will first turn to blue, then turn to yellow. The selected menu button will also be marked by a black check mark.

Press the BACK button (7) to return to the previous menu.

Press the HOME button (8) to return to the Home page (Performance page).

Service > Configurations > Payload > Scale Data Source

Note: The Service Mode must be enabled.

Illustration 42	g06222065
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (61) Scale Data Source menu button

1. Press the Scale Data Source menu button (61). The button will turn to blue, then turn to yellow. The Scale Data Source menu page will appear.
   Show/hide table

   Illustration 43	g06222242
   (7) BACK button (8) HOME button (62) Cat® menu button (63) Other menu button

2. Press the intended menu button (Cat® - (62) or Other - (63)). The menu button will first turn to blue, then turn to yellow. The selected menu button will also be marked by a black check mark.

Press the BACK button (7) to return to the previous menu.

Press the HOME button (8) to return to the Home page (Performance page).

Service > Configurations > Payload > Cat® Scale Demo

Note: The Cat^® Production Measurement (CPM) feature is not installed.

Illustration 44	g06222250
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (64) Cat® Scale Demo menu button

1. Press the Cat^® Scale Demo menu button (64). The button will turn to blue, then turn to yellow. The Cat^® Scale Demo menu page will appear.
   Show/hide table

   Illustration 45	g06222252
   Cat® Scale Demo menu page (7) BACK button (8) HOME button (65) Installed menu button (66) Not Installed menu button

2. Press the intended menu button (Installed - (65) or Not Installed - (66)). The menu button will first turn to blue, then turn to yellow. The selected menu button will also be marked by a black check mark.

Press the BACK button (7) to return to the previous menu.

Press the HOME button (8) to return to the Home page (Performance page).

Service > Configurations > Payload > Cat® Scale

Note: The Service Mode must be enabled.

Illustration 46	g06222268
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (67) Cat® Scale menu button

1. Press the Cat^® Scale menu button (67). The button will turn to blue, then turn to yellow. The Cat^® Scale menu page will appear.
   Show/hide table

   Illustration 47	g06222295
   Cat® Scale menu page (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (68) Enabled menu button (69) Disabled menu button

2. Press the intended menu button (Enabled - (68) or Disabled - (69)). The menu button will first turn to blue, then turn to yellow. The selected menu button will also be marked by a black check mark.

Press the BACK button (7) to return to the previous menu.

Press the HOME button (8) to return to the Home page (Performance page).

Trans (Transmission) Oil Type

Service > Configurations > Trans(mission) Oil Type

Note: The Service Mode must be enabled.

Note: This feature is available for the following machine models:

• 966 M CVT HRC (B8P)(P6C)

• 972 M CVT HRC (M5S)(EDW)

Illustration 48	g06222325
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (70) Trans Oil Type menu button

1. Press the Trans Oil Type menu button (70). The button will turn to blue, then turn to yellow. The Trans Oil Type menu page will appear.
   Show/hide table

   Illustration 49	g06222337
   Trans Oil Type menu page (7) BACK button (8) HOME button (71) Cat® TDTO™ Cold Weather 0W-20 menu button (72) Cat® SATO menu button

2. Press the intended menu button (Cat^® Cold Weather 0W-20 - (71) or Cat^® SATO - (72)). The menu button will first turn to blue, then turn to yellow. The selected menu button will also be marked by a black check mark.

Press the BACK button (7) to return to the previous menu.

Press the HOME button (8) to return to the Home page (Performance page).

Calibrations

Service > Calibrations

Note: Most calibrations menu items will show when the Service Mode is enabled.

For more information, refer to the following section in this manual:

• Service > Service Mode

Illustration 50	g06222354
Service menu page (3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (73) Calibrations menu button

1. Press the Service button (1) that is located on the right side of the Information Display. The Service menu page will appear.

2. Press the Calibrations menu button (73). The button will turn first to blue, then turn to yellow. The Calibrations menu page will appear.

Note: Some Calibrations will not appear in Medium Wheel Loader (MWL) menus. Show or hide conditions will depend upon the MWL model and its equipped features.

Illustration 51	g06222361
Calibrations menu list page (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (74) Calibrations menu button group

The Calibrations menu list page contains the following menu buttons:

• Payload

• Implement

Calibration Menus

Service > Calibrations > Payload (If Cat^® Production Measurement is installed)

Illustration 52	g06222371
Payload menu list page (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (75) Payload menu button group

The Payload menu list page contains the following menu buttons:

• Empty Bucket Weight

• Full Bucket Weight

• Calibration Weight

• Simple Calibration

Service > Calibrations > Payload > Empty Bucket Weight

Note: The Service Mode must be enabled.

Illustration 53	g06222376
Payload menu page (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (76) Empty Bucket Weight menu button

Note: Reference the “Cat^® Production Measurement (CPM) Systems Operations Manual (M0079530)” for more details on calibrating the Payload system.

1. Press the Empty Bucket Weight menu button (76). The button will first turn to blue, then turn to yellow. The Empty Bucket Weight warning information page will appear.
   Show/hide table

   Illustration 54	g06222402
   Empty Bucket Weight warning information page (3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button

2. Press the DOWN Arrow button (6) to begin scrolling down the page. The UP Arrow button (4) will become active and appear while scrolling.

3. Read the whole warning message and instructions. Ensure that the corresponding instructions are being followed. The Menu Sliding Indicator of the Non-Interactive Scroll Bar (3) will scroll along with the page.

4. The OK button (5) will appear at the bottom of the page and become active. Press the OK button to continue to the next step.

5. Press the BACK button (7) to return to the previous page.
   Show/hide table

   Illustration 55	g06222410
   (5) OK button

6. Press the OK button (5) to begin the calibration procedure.
   Show/hide table

   Illustration 56	g06222451
   (4) UP Arrow button (6) DOWN Arrow button (77) ABORT button (78) NEXT Arrow button

7. Press the DOWN Arrow button (6) or the UP Arrow button (4) to read the instructions.

8. Press the NEXT Arrow button (78) to continue the calibration procedure.

9. Press the ABORT button (77) to discontinue the procedure.
   Show/hide table

   Illustration 57	g06222466
   (5) OK button (77) ABORT button (78) NEXT Arrow button

10. Follow the instructions until the procedure is finished and the calibration is successful. Press the OK button (5) to return to the previous menu.
    Show/hide table

    Illustration 58	g06222472
    (5) OK button

11. If the Calibration has been aborted or has been unsuccessful, press the OK button (5) to return to the previous menu.

Illustration 59	g06222474
(77) ABORT button

To abort the Calibration procedure, perform the following steps:

1. Press the ABORT button (77).
   Show/hide table

   Illustration 60	g06222476
   (5) OK button (7) BACK button

2. The screen will ask “Are you sure you want to abort?”. Press the OK button (5) to continue aborting the procedure. Press the BACK button (7) to return to the previous Calibration procedure screen.

Service > Calibrations > Payload > Full Bucket Weight

Note: The Service Mode must be enabled.

Illustration 61	g06222486
(4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (79) Full Bucket Weight menu button

Note: Reference the “Cat^® Production Measurement (CPM) Systems Operations Manual (M0079530)” for more details on calibrating the Payload system.

1. Press the Full Bucket Weight menu button (79). The button will first turn to blue, then turn to yellow. The Full Bucket Weight menu screen will appear.
   Show/hide table

   Illustration 62	g06222490
   Full Bucket Weight warning information page (3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button

2. Press the DOWN Arrow button (6) to begin scrolling down the page. The UP Arrow button (4) will become active and appear while scrolling.

3. Read the whole warning message and instructions. Ensure that the corresponding instructions are being followed. The Menu Sliding Indicator of the Non-Interactive Scroll Bar (3) will scroll along with the page.

4. The OK button (5) will appear at the bottom of the page and become active. Press the OK button to continue to the next step.

5. Press the BACK button (7) to return to the previous page.
   Show/hide table

   Illustration 63	g06222506
   (5) OK button

6. Press the OK button (5) to begin the calibration procedure.
   Show/hide table

   Illustration 64	g06222514
   (4) UP Arrow button (6) DOWN Arrow button (77) ABORT button (78) NEXT Arrow button

7. Press the DOWN Arrow button (6) or the UP Arrow button (4) to read the instructions.

8. Press the NEXT Arrow button (78) to continue the calibration procedure.

9. Press the ABORT button (77) to discontinue the procedure.
   Show/hide table

   Illustration 65	g06222530
   (5) OK Arrow button (77) ABORT button (78) NEXT Arrow button

10. Follow the instructions until the procedure is finished and the calibration is successful. Press the OK button (5) to return to the previous menu.
    Show/hide table

    Illustration 66	g06222536
    (5) OK Arrow button

11. If the Calibration has been aborted or has been unsuccessful, press the OK button (5) to return to the previous menu.

Illustration 67	g06222760
(77) ABORT button

To abort the Calibration procedure, perform the following steps:

1. Press the ABORT button (77).
   Show/hide table

   Illustration 68	g06222764
   (5) OK button (7) BACK button

2. The screen will ask “Are you sure you want to abort?”. Press the OK button (5) to continue aborting the procedure. Press the BACK button (7) to return to the previous Calibration procedure screen.
   Show/hide table

   Illustration 69	g06222536
   (5) OK Arrow button

3. The Calibration Unsuccessful screen will appear. Press the OK button (5) to exit the Calibration.

Service > Calibrations > Payload > Calibration Weight

Note: The Service Mode must be enabled.

Illustration 70	g06222788
(4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (80) Calibration Weight menu button

Note: Reference the “Cat^® Production Measurement (CPM) Systems Operations Manual (M0079530)” for more details on calibrating the Payload system.

1. Press the Calibration Weight menu button (80). The button will turn to blue, then turn to yellow. The Calibration Weight settings page will appear.
   Show/hide table

   Illustration 71	g06222804
   (7) BACK button (8) HOME button (81) ENTER DATA button

2. Press the ENTER DATA button (81). The Calibration Weight keyboard appears.
   Show/hide table

   Illustration 72	g06222816
   Calibration Weight Numerical Keypad (5) OK button (7) BACK button (8) HOME button (82) Keypad BACK button (83) Estimated Cal Weight readout screen

3. The system provides an Estimated Calibration Weight that is calculated based on the results of the Empty Bucket Weight and Full Bucket Weight procedures. This allows the system to be calibrated if the site scales are not available to confirm the actual weight of material used for the Full Bucket Weight calibration.

4. Enter the desired Calibration Weight number with the keypad. This can be the same as the Estimated Calibration Weight or a known weight calculated from site scales. Press the OK button (5) to set the entry.

5. Correct a mistyped number by pressing the Keypad BACK button (82), then reenter the correct number.

6. Press the BACK button (7) to return to the previous page.

7. Press the HOME button (8) to return to the Home page (Performance Page 1).

Service > Calibrations > Payload > Simple Calibration

Illustration 73	g06222838
Payload menu page (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (84) Simple Calibration menu button

1. Press the Simple Calibration menu button (84). The button will first turn to blue, then turn to yellow. The Simple Calibration data page will appear.

   The Simple Calibration data page has the following columns:

   • Truck ID (Identification)

   • Weight

   The weight data corresponds to the Truck ID number that is in the same row.

   Show/hide table

   Illustration 74	g06222847
   Simple Calibration data page (3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (85) Double UP Arrow button (86) Double DOWN Arrow button

2. Press the UP Arrow button (4) or the DOWN Arrow button (6) to select the intended row. The row will be highlighted with a yellow strip.

3. Press the OK button (5). The numerical keypad page for the corresponding Truck ID will appear.
   Show/hide table

   Illustration 75	g06222855
   Numerical keypad page (5) OK button (7) BACK button (8) HOME button (82) Keypad BACK button

4. Enter the intended weight number into the numerical keypad. To correct an error, press the Keypad BACK button (82) to backspace over the incorrect number.

5. Press the OK button (5) to enter the intended truck weight number.

The updated weight data is now visible on the Simple Calibration data page.

Note: To change the weight units between English to Metric, refer to the following section in this manual:

• Display > Units

Service > Calibrations > Implement

Note: The Service Mode must be enabled.

The Implement menu list page contains the following menu buttons:

• Linkage Sensors

• Implement Valves

Service > Calibrations > Implement > Linkage Sensors

The Linkage Sensors menu list page contains the following menu buttons:

• Lift Sensor

• Tilt Sensor

Service > Calibrations > Implement > Implement Valves

The Implement Valves menu list page contains the following menu buttons:

• Raise Valve

• Dump Valve

• Rackback Valve

• Lower Valve

• 3^rd Function Fwd (Forward) Valve (If the Third Function feature is enabled)

• 3^rd Function Rwd (Rearward) Valve (If the Third Function feature is enabled)

• 4^th Function Fwd (Forward) Valve (If the Fourth Function feature is enabled)

• 4^th Function Rwd Valve (Rearward) (If the Fourth Function feature is enabled)

• Autodig Rackback Valve (If the Autodig feature is installed)

• Rack and Dump (Max(imum)) (The Machine Model Number is among the PS product line and the Service Mode must be enabled.)

• Raise Valve (Max(imum)) (The Machine Model Number is among the PS product line and the Service Mode must be enabled.)

Note: The PS product line contains the following machine models:

• 950M PS HRC

• 962M PS HRC

• 966M PS HRC

• 972M PS HRC

• 980M PS HRC

• 982M PS HRC

• 950M PS LRC

• 962M PS LRC

• 966M PS LRC

• 972M PS LRC

• 980M PS LRC

• 982M PS LRC

Service > Calibrations > Implement > Linkage Sensors > Tilt Sensor

Note: The Service Mode is enabled.

Note: The calibration procedure for Tilt Sensor is similar to the other implement calibration procedures.

Illustration 76	g06222879
(4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (87) Implement menu button

1. Press the Implement menu button (87). The button will turn first to blue, then to yellow. The Implement menu screen will appear.
   Show/hide table

   Illustration 77	g06222893
   (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (88) Linkage Sensors menu button

2. Press the Linkage Sensors menu button (88). The button will turn first to blue, then to yellow. The Linkage Sensors screen will appear.
   Show/hide table

   Illustration 78	g06222906
   (7) BACK button (8) HOME button (89) Tilt Sensor menu button

3. Press the Tilt Sensor menu button (89). The button will turn first to blue, then turn to yellow. The Tilt Sensor calibration screen will appear.
   Show/hide table

   Illustration 79	g06222914
   (5) OK button (7) BACK button

4. Read the safety statement.

5. Press the OK button (5) to proceed.

6. Press the BACK button (7) to return to the previous menu.
   Show/hide table

   Illustration 80	g06222940

7. Press the OK button to start the calibration.
   Show/hide table

   Illustration 81	g06222945
   (77) ABORT button (78) NEXT button

8. Follow the instructions on the screen.

9. Press the ABORT button (77) to discontinue the calibration.

10. Press the NEXT button (78) to continue the calibration.
    Show/hide table

    Illustration 82	g06222950

11. Follow the instructions on the screen.

12. Press the ABORT button (77) to discontinue the calibration.

13. Press the NEXT button (78) to continue the calibration.
    Show/hide table

    Illustration 83	g06222954

14. Follow the instructions on the screen.

15. Press the ABORT button (77) to discontinue the calibration.

16. Press the NEXT button (78) to continue the calibration.
    Show/hide table

    Illustration 84	g06222958

17. Follow the instructions on the screen.

18. Press the ABORT button (77) to discontinue the calibration.

19. Press the NEXT button (78) to continue the calibration.
    Show/hide table

    Illustration 85	g06222965

20. Follow the instructions on the screen.

21. Press the ABORT button (77) to discontinue the calibration.

22. Press the NEXT button (78) to continue the calibration.
    Show/hide table

    Illustration 86	g06222984

23. If the calibration is successful, the “Calibration Successful” screen will appear. Press the OK button to acknowledge and to exit the Calibration.
    Show/hide table

    Illustration 87	g06222987

24. If the ABORT button is pressed anytime during the calibration, the “Calibration Unsuccessful” screen will appear. Press the OK button to proceed.
    Show/hide table

    Illustration 88	g06222990

25. A dialog box will appear and ask, “Are you sure you want to abort?”.

26. Press the OK button to discontinue the calibration.

27. Press the BACK button to return to the previous screen.

Lockup Clutch Capacity Test

Service > Lockup Clutch Capacity Test

The Service Mode must be enabled.

The Machine Model Number is the following:

• 950M PS HRC

• 962M PS HRC

• 966M PS HRC

• 972M PS HRC

• 980M PS HRC

• 982M PS HRC

• 950M PS LRC

• 962M PS LRC

• 966M PS LRC

• 972M PS LRC

• 980M PS LRC

• 982M PS LRC

Illustration 89	g06223000
(90) Lockup Clutch Capacity Test

1. Press the Lockup Clutch Capacity Test menu button (90). The button will turn blue, then yellow. The Lockup Clutch Capacity Test page will appear.
   Show/hide table

   Illustration 90	g06223006
   (3) Non-Interactive Scroll bar with Menu Sliding Indicator (6) DOWN Arrow button

   Show/hide table

   Illustration 91	g06223009
   (4) UP Arrow button

   Show/hide table

   Illustration 92	g06223010
   (5) OK button (7) BACK button

2. The UP Arrow button will not be visible when the instruction text is scrolled to the top of the page. Press the DOWN Arrow button (6) to scroll down the page. The UP Arrow button (4) will then appear. The sliding indicator of the Non-Interactive Scroll Bar (3) will move accordingly with the page.

3. The DOWN Arrow button (6) will not be visible when the page has been scrolled to the bottom. The OK button (5) will appear. Press the OK button to continue through the test. Press the BACK button (7) to return to the previous menu.

4. Read the instructions thoroughly before beginning the test.
   Show/hide table

   Illustration 93	g06027331

5. Press the OK button to start the test.
   Show/hide table

   Illustration 94	g06027332

   Show/hide table

   Illustration 95	g06223013
   (77) ABORT button (78) NEXT button

6. To scroll through the “Set up conditions” instructions, use the DOWN Arrow button (6) or the UP Arrow button (4). The sliding indicator of the Non-Interactive Scroll Bar (3) will move accordingly.

7. To continue with the test, press the NEXT button (78).
   Show/hide table

   Illustration 96	g06027338

   Note: To abort the test, press the ABORT button (77) at any time. Press the OK button to abort the test. Press the BACK button to return to the previous page. Press the OK button again to return to the Service menu page.

   Show/hide table

   Illustration 97	g06027340

8. Follow the instructions on the page. Press the NEXT button (78) to continue with the test.
   Show/hide table

   Illustration 98	g06027343

9. The test has been completed and no issues were detected. Follow the instructions on the page. Press the NEXT button (78) to continue with the test.
   Show/hide table

   Illustration 99	g06027344

10. If the Service Test has been successful, Press the OK button (5) to return to the Service menu page.
    Show/hide table

    Illustration 100	g06027348

11. The test has been completed but the clutch failed the test. Follow the instructions on the page. Press the NEXT button (78) to continue with the test.
    Show/hide table

    Illustration 101	g06027350

12. The Service Test was unsuccessful. Press the OK button (5) to return to the Service menu page.

ECM Summary

Service > ECM Summary

Illustration 102	g06223029
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (91) ECM Summary menu button

1. Press the ECM Summary menu button (91). The button will turn to blue, then in yellow. The ECM Summary menu page will appear.
   Show/hide table

   Illustration 103	g06223034
   (3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (92) ECM Summary menu buttons

   Show/hide table

   Illustration 104	g06223036
   (7) BACK button (8) HOME button

   Note: Above is an example of the Service > ECM Summary > Engine. The ECM Summary information will vary depending on the machine model and its equipped features.

2. Use the UP Arrow button (4) or the DOWN Arrow button (6) to scroll through the ECM Summary menu page. Menu Sliding Indicator will move along with the Non-Interactive Scroll Bar (3).

3. Press an intended menu button (92) in the menu button group (Example: Engine). The button will turn to blue, then turn to yellow. The selected item’s ECM Summary information will appear.

ECM Summary Information is available for the following items:

• Engine

• Aftertreatment

• Implement

• Transmission

• VIMS

• Display 1 – Indication Display

• Display 2 – Information Display

Service Mode

Service > Service Mode

Note: The numerical keypad only appears when the Service Mode is disabled.

Illustration 105	g06223069
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (93) Service Mode menu button

Illustration 106	g06223072
(5) OK button (7) BACK button (82) Keypad (Only appears when the Service Mode is disabled)

1. Press the Service Mode menu button (93). A numerical keypad will appear if the Service Mode is disabled. A keypad will not appear if the Service Mode is already activated.

2. Enable the Service Mode when the keypad appears. Enter a pass code on the keypad. Press the OK button (5).

3. Press the Keypad BACK button (82) to backspace over an incorrect entry.

   Note: The default Service Mode password is set to "1234". To change the Service Mode pass code from the default, see "Service Mode Enable Code" configuration under "Graphical Display" ECM in Cat^® Electronic Technician (Cat ET) Service Tool.

4. Press the BACK button (7) and the Service Mode Enable/Disable page will appear.

5. Press the intended menu button (Enabled or Disabled). The menu button will first turn to blue, then turn to yellow. A black check mark will appear in the selected button.

Illustration 107	g06223076
(7) BACK button (8) HOME button (94) Service Mode menu button group (Enable or Disable)

Note: Show / Hide Conditions exist in the current Service Menu page when the Service Mode is either enabled or disabled:

• Currently, most Configurations will show whether the Service Mode is enabled or disabled.

• Most Calibrations will show only when the Service Mode is enabled.

Note: The Cat^® Production Measurement (CPM) Simple calibration will be present in the Service > Calibrations > Payload menu if CPM is installed, regardless of a service password.

Press the BACK button (7) to return to the previous page.

Press the HOME button (8) to return to the Home page.