950M, 962M, 966M, 972M, 980M, and 982M Wheel Loaders Information Display Caterpillar

Illustration 1	g06218310
(1) Machine button

Press the Machine button (1) to view and adjust settings within Machine menus, which are:

• Settings

• Parameters

Illustration 2	g06218324
(2) Machine Menu buttons (Settings or Parameters) (3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button

Press the intended Machine menu button (Settings or Parameters). The intended menu button will first turn to blue, then to yellow. The intended submenu page will appear.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

Machine Settings

Machine > Settings

Illustration 3	g06218326
Machine menu page (3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (8) Settings menu button

1. Press the Machine button (1) located on the right side of the Information Display. The Machine menu page will appear.

2. Press the Settings menu button (8) on the menu page. The button will turn first to blue, then to yellow. The Settings menu page will appear.
   Show/hide table

   Illustration 4	g06218336
   Settings menu page (3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (9) Settings menu buttons (10) Non-Interactive Scroll Bar with Menu Sliding Indicator

3. The Settings menu page contains the following menu buttons:

   • Implement

   • Ride Control

   • Transmission

   • Payload Settings

   • Rimpull (966M CVT HRC or 972M CVT HRC)

   • Functions

   • Automatic Differential Lock

   • Economy Mode

   Press the UP Arrow button (3) to scroll the Menu Settings list up. Press the DOWN Arrow button (5) to scroll the Menu Settings list down. When visible, the Menu Sliding Indicator of the Non-Interactive Scroll Bar (10) will move accordingly. The menu list can be scrolled around to the beginning.

   Press the BACK button (6) to return to the previous page.

   Press the HOME button (7) to return to the Home page (Performance Page).

Machine Settings: Implement

Machine > Settings > Implement

Illustration 5	g06218341
Settings menu page (3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (11) Implement menu button

1. Press the Machine button (1) located on the right side of the Information Display. The Machine menu page will appear.

2. Press the Settings menu button (8). The button will turn first to blue, then to yellow. The Settings menu page will appear.

3. Press the Implement menu button (11). The button will turn first to blue, then to yellow. The Implement menu page will appear.

4. Use the UP Arrow button (3) or DOWN Arrow button (5) to scroll through the Implement menu button group. The Menu Sliding Indicator on the Non-Interactive Scroll Bar (10) will move with the page.

The Implement menu page will have the following menu buttons:

• Modulation

• 3^rd Function Detent

• 3^rd Function Flow

• 4^th Function Flow

• Parallel Lift

• Dump Rate

• Rack Limiting

• Raise Snubbing

• Lower Snubbing

• Rack Snubbing

• Dump Snubbing

• Dump Stop Snubbing

Modulation

Machine > Settings > Implement > Modulation

Note: The Work Tool Control System (WTCS) must be installed.

Illustration 6	g06218394
(4) OK button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (12) Modulation menu button (13) Modulation menu button group (Normal or Fine)

1. Press the Machine button (1) located on the right side of the Information Display. The Machine menu page will appear.

2. Press the Settings menu button (2). The button will turn first to blue, then to yellow. The Settings menu page will appear.

3. Press the Implement menu button (11). The button will turn first to blue, then to yellow. The Implement menu page will appear.

4. Use the UP Arrow button (3) or DOWN Arrow button (5) to scroll through the Implement menu button group. The Menu Sliding Indicator on the Non-Interactive Scroll Bar (10) will move with the page.

5. Press the Modulation menu button (12). The button will turn first to blue, then to yellow. The Modulation settings page will appear.

6. Press the intended button in the Modulation menu button group (13) (Normal or Fine). The button will turn first to blue, then to yellow. A black check mark will appear next to the selection. Press the OK button (4) to set.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

Fine Modulation Mode

Machine > Settings > Implement > Fine Modulation Mode

Note: The Work Tool Control System (WTCS) is not installed.

Illustration 7	g06218428
(4) OK button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (14) Fine Modulation Mode menu button (15) Fine Modulation Mode menu button group (Enabled or Disabled)

1. Press the Machine button (1) located on the right side of the Information Display. The Machine menu page will appear.

2. Press the Settings menu button (2). The button will turn first to blue, then to yellow. The Settings menu page will appear.

3. Press the Implement menu button (11). The button will turn first to blue, then to yellow. The Implement menu page will appear.

4. Use the UP Arrow button (3) or DOWN Arrow button (5) to scroll through the Implement menu button group. The Menu Sliding Indicator on the Non-Interactive Scroll Bar (10) will move with the page.

5. Press the Fine Modulation Mode menu button (14). The button will turn first to blue, then to yellow. The Modulation settings page will appear.

6. Press the intended button in the Modulation menu button group (15) (Enabled or Disabled). The button will turn first to blue, then to yellow. A black check mark will appear next to the selection. Press the OK button (4) to set.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

3rd Function Detent

Machine > Settings > Implement > 3rd Function Detent

Note: The Third Function must be installed.

Illustration 8	g06218415
(4) OK button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (16) 3rd Function Flow menu button (17) 3rd Function Detent Menu button group (Off or Continuous Flow)

1. Press the Machine button (1) located on the right side of the Information Display. The Machine menu page will appear.

2. Press the Settings menu button (2). The button will turn first to blue, then to yellow. The Settings menu page will appear.

3. Press the Implement menu button (11). The button will turn first to blue, then to yellow. The Implement menu page will appear.

4. Use the UP Arrow button (3) or DOWN Arrow button (5) to scroll through the Implement menu button group. The Menu Sliding Indicator on the Non-Interactive Scroll Bar (10) will move with the page.

5. Press the 3^rd Function Detent menu button (16). The button will turn first to blue, then to yellow. The 3^rd Function Detent settings page will appear.

6. Press the intended button in the 3^rd Function Detent menu button group (17) (Off or Continuous Flow). The button will turn first to blue, then to yellow. A black check mark will appear next to the selection. Press the OK button (4) to set.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

3rd Function Flow

Machine > Settings > Implement > 3rd Function Flow

Note: The Third Function must be installed.

Illustration 9	g06218434
(10) Non-Interactive Scroll Bar with Menu Sliding Indicator (18) 3rd Function Flow menu button (19) MINUS (-) Arrow button – Increment/Decrement bar (20) PLUS (+) Arrow button – Increment/Decrement bar

1. Press the Machine button (1) located on the right side of the Information Display. The Machine menu page will appear.

2. Press the Settings menu button (2). The button will turn first to blue, then to yellow. The Settings menu page will appear.

3. Press the Implement menu button (11). The button will turn first to blue, then to yellow. The Implement menu page will appear.

4. Use the UP Arrow button (3) or DOWN Arrow button (5) to scroll through the Implement menu button group. The Menu Sliding Indicator on the Non-Interactive Scroll Bar (10) will move with the page.

5. Press the 3^rd Function Flow menu button (18). The button will turn first to blue, then to yellow. The 3^rd Function Flow settings page will appear.

6. Use the Increment/Decrement bar to enter the Maximum Valve Flow percentage in either Port A and Port B.

7. Press the PLUS (+) Arrow button (20) to increase the number. Press the MINUS (-) Arrow button (19) to decrease the number.

8. Press the OK button (4) to set the number. The newly set number will appear in white text.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

4th Function Flow

Machine > Settings > Implement > 4th Function Flow

Note: The Fourth Function must be installed.

Illustration 10	g06218845
(10) Non-Interactive Scroll Bar with Menu Sliding Indicator (19) MINUS (-) Arrow button – Increment/Decrement bar (20) PLUS (+) Arrow button – Increment/Decrement bar (21) 4th Function Flow menu button

1. Press the Machine button (1) located on the right side of the Information Display. The Machine menu page will appear.

2. Press the Settings menu button (2). The button will turn first to blue, then to yellow. The Settings menu page will appear.

3. Press the Implement menu button (11). The button will turn first to blue, then to yellow. The Implement menu page will appear.

4. Use the UP Arrow button (3) or DOWN Arrow button (5) to scroll through the Implement menu button group. The Menu Sliding Indicator on the Non-Interactive Scroll Bar (10) will move with the page.

5. Press the 4^rh Function Flow menu button (21). The button will turn first to blue, then to yellow. The 4^rh Function Flow settings page will appear.

6. Use the Increment/Decrement bar to enter the Maximum Valve Flow percentage in either Port A and Port B.

7. Press the PLUS (+) Arrow button (20) to increase the number. Press the MINUS (-) Arrow button (19) to decrease the number.

8. Press the OK button (4) to set the number. The newly set number will appear in white text.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

Parallel Lift

Machine > Settings > Implement > Parallel Lift

Note: This feature is available on the following models:

• 950M PS HRC

• 950M PS LRC

• 962M PS HRC

• 962M PS LRC

Illustration 11	g06218855
(3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (22) Parallel Lift menu button (23) Parallel Lift menu button group (Enabled or Disabled)

1. Press the Machine button (1) located on the right side of the Information Display. The Machine menu page will appear.

2. Press the Settings menu button (2). The button will turn first to blue, then to yellow. The Settings menu page will appear.

3. Press the Implement menu button (11). The button will turn first to blue, then to yellow. The Implement menu page will appear.

4. Use the UP Arrow button (3) or DOWN Arrow button (5) to scroll through the Implement menu button group. The Menu Sliding Indicator on the Non-Interactive Scroll Bar (10) will move with the page.

5. Press the Parallel Lift menu button (22). The button will turn first to blue, then to yellow. The Parallel Lift settings page will appear.

6. Press either the Enabled menu button or the Disabled menu button in the Parallel Lift menu button group (23). The selected button will turn first to blue, then to yellow. A check mark will appear next to the selection. Press the OK button (4) to set.

7. Press the BACK button (6) to return to the previous menu.

8. Press the HOME button (7) to return to the previous menu (Performance Page).

Dump Rate

Machine > Settings > Implement > Dump Rate

Illustration 12	g06218877
(3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (24) Dump Rate menu button (25) Dump Rate menu button group (Enabled or Disabled)

1. Press the Machine button (1) located on the right side of the Information Display. The Machine menu page will appear.

2. Press the Settings menu button (2). The button will turn first to blue, then to yellow. The Settings menu page will appear.

3. Press the Implement menu button (11). The button will turn first to blue, then to yellow. The Implement menu page will appear.

4. Use the UP Arrow button (3) or DOWN Arrow button (5) to scroll through the Implement menu button group. The Menu Sliding Indicator on the Non-Interactive Scroll Bar (10) will move with the page.

5. Press the Dump Rate menu button (24). The button will turn first to blue, then to yellow. The Dump Rate settings page will appear.

6. Press either the Enabled menu button or the Disabled menu button in the Dump Rate menu button group (25). The selected button will turn first to blue, then to yellow. A check mark will appear next to the selection. Press the OK button (4) to set.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

Rack Limiting

Machine > Settings > Implement > Rack Limiting

Note: This feature is available on the following models:

• 980 M PS LRC

Note: The Implement Linkage Configuration is set to Block Handler.

Illustration 13	g06218883
(3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (26) Rack Limiting menu button (27) Rack Limiting switch (28) Current Limit reading (29) SAVE button (30) Rack Pos(ition) reading (in degrees)

1. Press the Machine button (1) located on the right side of the Information Display. The Machine menu page will appear.

2. Press the Settings menu button (2). The button will turn first to blue, then to yellow. The Settings menu page will appear.

3. Press the Implement menu button (11). The button will turn first to blue, then to yellow. The Implement menu page will appear.

4. Use the UP Arrow button (3) or DOWN Arrow button (5) to scroll through the Implement menu button group. The Menu Sliding Indicator on the Non-Interactive Scroll Bar (10) will move accordingly.

5. Press the Rack Limiting menu button (26). The button will turn first to blue, then to yellow. The Rack Limiting settings page will appear.

6. Press the Rack Limiting switch (27). Rack Limiting is OFF if the switch is gray and in the left side position. Rack Limiting is ON if the switch is green and in the right side position.

7. Press the SAVE button (29) to set the current rack position (30) as the current limit (28).

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

Implement Snubbing Settings

There are five types of Implement Snubbing Settings:

• Raise Snubbing

• Lower Snubbing

• Rack Snubbing (Model is a 966 or 972 or 980 or 982)

• Dump Snubbing

• Dump Stop Snubbing

Note: All five Implement Snubbing Settings have similar menu buttons (Enabled or Disabled).

Example: Raise Snubbing

Machine > Settings > Implement > Raise Snubbing

Illustration 14	g06218899
(3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (31) Raise Snubbing menu button (32) Raise Snubbing menu button group (Enabled or Disabled)

1. Press the Machine button (1) located on the right side of the Information Display. The Machine menu page will appear.

2. Press the Settings menu button (2). The button will turn first to blue, then to yellow. The Settings menu page will appear.

3. Press the Implement menu button (11). The button will turn first to blue, then to yellow. The Implement menu page will appear.

4. Use the UP Arrow button (3) or DOWN Arrow button (5) to scroll through the Implement menu list. The Menu Sliding Indicator on the Non-Interactive Scroll Bar (10) will move accordingly.

5. Press the Raise Snubbing menu button (31). The button will turn first to blue, then to yellow. The Raise Snubbing settings page will appear.

6. Press either the Enabled menu button or the Disabled menu button in the Raise Snubbing menu button group. The selected button will turn first to blue, then to yellow. A check mark will appear next to the selection. Press the OK button (4) to set.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

Ride Control

Machine > Settings > Ride Control

Note: The Ride Control feature must be installed.

Illustration 15	g06218907
(3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (33) Ride Control menu button (34) Enter Data button (Forward Activation Speed) (35) Enter Data button (Reverse Activation Speed)

Illustration 16	g06218911
(36) KEYPAD BACK SPACE button

Forward Activation Speed

Machine > Settings > Ride Control > Forward Activation Speed

1. Press the Machine button (1) on the right side of the Display. The Machine menu page will appear.

2. Press the Settings button (2). The button will highlight in blue, then in yellow. The Settings menu page will appear.

3. Press the Ride Control button (33). The button will highlight in blue, then in yellow. The Ride Control menu page will appear.

4. Press the Enter Data button (34) located in the Forward Activation Speed box. A keypad will appear.

5. On the keypad, type in an intended number for Forward Activation Speed. Press the KEYPAD BACK SPACE button (36) to reenter a number.

6. Press the OK button (4) to set the number.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

Reverse Activation Speed

Machine > Settings > Ride Control > Reverse Activation Speed

1. Press the Machine button (1) on the right side of the Display. The Machine menu page will appear.

2. Press the Settings button (2). The button will highlight in blue, then in yellow. The Settings menu page will appear.

3. Press the Ride Control button (33). The button will highlight in blue, then in yellow. The Ride Control menu page will appear.

4. Press the Enter Data button (35) located in the Reverse Activation Speed box. A keypad will appear.

5. On the keypad, type in an intended number for Forward Activation Speed. Press the KEYPAD BACK SPACE button (36) to reenter a number.

6. Press the OK button (4) to set the number.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

Transmission (Powershift Only)

Machine > Settings > Transmission

Note: This feature is available on the following models:

• 950_M_PS_HRC

• 962_M_PS_HRC

• 966_M_PS_HRC

• 972_M_PS_HRC

• 980_M_PS_HRC

• 982_M_PS_HRC

• 950_M_PS_LRC

• 962_M_PS_LRC

• 966_M_PS_LRC

• 972_M_PS_LRC

• 980_M_PS_LRC

• 982_M_PS_LRC

• 950_962_M_PS_HRC_Zbar

Illustration 17	g06218920
(3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (37) Transmission menu button

Max Gear

Machine > Settings > Transmission > Max Gear

Illustration 18	g06219158
(4) OK button (6) BACK button (7) HOME button (38) Max (Maximum) Gear menu button (39) Max (Maximum) Forward Gear Increment/Decrement bar (40) Max (Maximum) Reverse Gear Increment/Decrement bar

Maximum Forward Gear

Machine > Settings > Transmission > Max Gear > Max (Maximum) Forward Gear

1. Press the Machine button (1) on the right side of the Display. The Machine menu page will appear.

2. Press the Settings menu button (2). The button will turn first to blue, then to yellow. The Settings menu page will appear.

3. Press the Transmission menu button (37). The button will turn first to blue, then to yellow. The Transmission menu page will appear.

4. Press the Max Gear (Maximum Gear) menu button (38). The button will turn first to blue, then to yellow. The Max Gear settings page will appear.

5. Set the Max Forward Gear by pressing the PLUS (+) button on the right end of the Max Forward Gear Increment/Decrement bar (39). This action will increase the gear number. Press the MINUS (-) button on the left end of the Increment/Decrement bar to decrease the gear number.

6. When an intended number appears, press the OK button (4) to set. The newly set number will appear in white text.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

Maximum Reverse Gear

Machine > Settings > Transmission > Max Gear > Max (Maximum) Reverse Gear

1. Press the Machine button (1) on the right side of the Display. The Machine menu page will appear.

2. Press the Settings menu button (2). The button will turn first to blue, then to yellow. The Settings menu page will appear.

3. Press the Transmission menu button (37). The button will turn first to blue, then to yellow. The Transmission menu page will appear.

4. Press the Max Gear (Maximum Gear) menu button (38). The button will turn first to blue, then to yellow. The Max Gear settings page will appear.

5. Set the Max Reverse Gear by pressing the PLUS (+) button on the right end of the Max Reverse Gear Increment/Decrement bar (40). This action will increase the gear number. Press the MINUS (-) button on the left end of the Increment/Decrement bar to decrease the gear number.

6. When an intended number appears, press the OK button (4) to set. The newly set number will appear in white text.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

Directional Desired Gear

Machine > Settings > Transmission > Directional Desired Gear

Illustration 19	g06219199
(6) BACK button (7) HOME button (41) Directional Desired Gear menu button (42) Directional Desired Gear menu button group

1. Press the Machine button (1) on the right side of the Display. The Machine menu page will appear.

2. Press the Settings menu button (2). The button will turn first to blue, then to yellow. The Settings menu page will appear.

3. Press the Transmission menu button (37). The button will turn first to blue, then to yellow. The Transmission menu page will appear.

4. Press the Directional Intended Gear menu button (41). The button will turn first to blue, then to yellow. The Directional Intended Gear settings page will appear.

5. Press one of the following menu buttons in the Directional Intended Gear menu button group (42):

   • 1F - 2R

   • 2F - 2R

   • 1F - 1R

   • 2F - 1R

   The selected button will turn first to blue, then to yellow. A black check mark will also appear.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

Payload Settings

Machine > Settings > Payload Settings

Note: The Cat^® Production Measurement (CPM) feature must be installed.

Illustration 20	g06219291
(3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (43) Payload Settings menu button

1. Press the Payload Settings menu button (43). The Payload Settings menu page will appear with the following menu buttons:

   • Set Weigh Range

   • Printer Tickets

   • Tip-Off

   • Payload Display Mode

   • Weight Units

   • List Management

Illustration 21	g06219336
(3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (44) Payment Settings menu button group

2. Press the UP Arrow button (3) or the DOWN Arrow button (5) to scroll through the menu button group. The Menu Sliding Indicator of the Non-interactive Scroll Bar will move along with the page.

3. Press the intended menu button. The button will first turn to blue, then turn to yellow. The specific sub-page will appear.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

Set Weigh Range

Machine > Settings > Payload > Set Weigh Range

Illustration 22	g06219348
(3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (45) Set Weight Range menu button (46) Lower Limit Increment/Decrement bar (47) Weigh Range Increment/Decrement bar (48) Lift Cylinder Pos (Position) section

Set Weigh Range - Lower Limit

Machine > Settings > Payload > Set Weigh Range - Lower Limit

1. Use the Lower Limit Increment/Decrement bar (46) to set the Lower Limit percentage.

2. Press the PLUS (+) button on the right end of the Increment Bar to increase a number. Press the MINUS (-) button on the left end of the Increment/Decrement bar to decrease a number.

3. The newly set number will appear in white text. The Lift Cylinder Position (Lift Cylinder Pos) Digital Reading (52) will appear as a fixed percentage on the page.

Illustration 23	g06219353
(49) Lift Cylinder Position Percentage bar (50) Set Range – Lower End (51) Set Range – Upper End (52) Lift Cylinder Pos (Position) Digital Reading – Fixed Percentage

The cylinder on the screen shows the Lift Cylinder Position percentage based on the set values.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

Machine > Settings > Payload > Set Weigh Range – Weigh Range

1. Use the Weigh Range Increment/Decrement bar (47) to set the Weigh Range percentage.

2. Press the PLUS (+) button on the right end of the Increment/Decrement Bar to increase a number. Press the MINUS button (-) on the left end of the Increment/Decrement Bar to decrease a number.

3. The newly set number will appear in white text. The Lift Cylinder Position (Lift Cylinder Pos) Digital Reading (52) will appear as a fixed percentage on the page.

Illustration 24	g06219360
(52) Lift Cylinder Pos (Position) Digital Reading – Fixed Percentage

Printer Tickets

Machine > Settings > Payload > Printer Tickets

Note: The Cat^® Production Measurement (CPM) feature must be installed.

Note: Legacy VIMS is not installed.

Illustration 25	g06219406
(3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (53) Printer Tickets menu button (54) Printer Tickets setting page

1. Press the Printer Tickets menu button (53). The button will first turn to blue, then turn to yellow. The Printer Tickets settings page will appear.

2. Press the menu button for the number of tickets to be printed (“0”, “1”, “2”, or “3”). The selected button will first turn to blue, then turn to yellow. A check mark will appear in the selected menu button.

3. Press the OK button (4) to set.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

Tip Off

Machine > Settings > Payload > Tip Off

Illustration 26	g06219408
(3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (55) Tip-Off menu button (56) Tip-Off – Trigger setting (Auto, Manual or Disabled) (57) Tip-Off – Mode setting (Stockpile or Truck)

1. Press the Tip-Off menu button (55). The button will first turn to blue, then turn to yellow. The Tip-Off settings page will appear.

2. To set the Trigger setting (56) (Auto, Manual, or Disabled), press either the yellow UP Arrow button or the yellow DOWN arrow button. The text of the intended setting will enlarge, indicating that the Trigger setting has been set.

3. To set the Mode setting (57) (Stockpile or Truck), press either the yellow UP Arrow button or the yellow DOWN arrow button. The text of the intended setting will enlarge, indicating that Mode setting has been set.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

Payload Display Mode

Machine > Settings > Payload > Payload Display Mode

Illustration 27	g06219418
(3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (58) Payload Display Mode menu button (59) Payload Display Mode setting page (Normal or Simplified)

1. Press the Payload Display Mode menu button (58). The button will first turn to blue, then turn to yellow. The Weight Units settings page will appear.

2. Press the intended Payload Display Mode menu button (59) (Normal or Simplified). A black check mark will also appear on the button. Press the OK button (4) to set.

3. The Payload Performance page will show all its information when the Payload Display Mode is set to Normal. The Payload page will display a limited amount of information when the Payload Display Mode is set to Simplified.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

Illustration 28	g06219423
Payload Performance Page: Normal

Illustration 29	g06219425
Payload Performance Page when the Payload Display Mode is in the Simplified mode. (60) Tip-Off hotkey button

Note: When the Payload Performance page is in the Simplified mode, the Manual Tip-Off hotkey button (60) may or may not be visible.

If the Manual Tip-Off mode is enabled, the hotkey button will appear on the page. However, the toggle feature will not be operational.

If the Manual Tip-Off mode is disabled, the hotkey button will appear as blank on the page.

For more information, refer to the following section in this manual:

• Manual Tip-Off Button

Weight Units

Machine > Settings > Payload > Weight Units

Illustration 30	g06219431
(3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (61) Weight Units menu button (62) Weight Units setting page (Tons or lb X 1000 (klb))

1. Press the Weight Units menu button (61). The button will first turn to blue, then turn to yellow. The Weight Units settings page will appear.

2. Press the intended Weight Units menu button (62) (Tons or lb X 1000 (klb)). A black check mark will also appear on the button. Press the OK button (4) to set.

3. The Weight Unit will appear on the main Payload screen.

Press the BACK button (6) to return to the previous page.

Press the HOME button (7) to return to the Home page (Performance Page).

Illustration 31	g06219434
The Display > Units settings page

Note: When the user selects the English menu button in the Display > Units settings page, the Weight Units will always set to the Tons measurement by default.Also, when the user selects the English menu button in the Display > Units settings page, the Weight Units menu button will be visible on the Machine > Settings > Payload Settings page.

Note: The lb x 1000 (klb) menu button will be visible only when in the Display > Units settings page is set to English and will be hidden when in the Display > Units settings page is set to Metric.Also, when the user selects the Metrics menu button in the Display > Units settings page, the Weight Units menu button will not be visible on the Machine > Settings > Payload Settings page.

For more information, refer to the following section in this manual:

• Display > Units

Illustration 32	g06219438
Payload Performance Page with the Payload measurement in “Tons” (English)

Illustration 33	g06219440
Payload Performance Page with the Payload measurement in “lb x 1000” (English)

Illustration 34	g06219423
Payload Performance Page with the Payload measurement in “tonnes” (Metric).

Note: The klb feature shall be applied to production parameters such as lb X1000 per gallon and lb X1000 per hour (klb/gal and klb/h).

Note: It is not possible to combine English units and Metric units, such as klb/L.

List Management

Payload Settings > List Management

Illustration 35	g06219458
(3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (63) List Management menu button (64) List Management menu button group

1. Press the List Management menu button (63). The menu button will first turn blue, then turn yellow.

2. Press the intended menu button. Choose between the following:

   • Truck List

   • Material

Example: Truck List

Payload Settings > List Management > Truck List

Note: The navigation process for Payload Settings > List Management > Truck List is the same for Payload Settings > List Management > Material List

Illustration 36	g06219474
(6) BACK button (7) HOME button (65) Truck menu button

1. Press the Truck menu button (65). The menu button will first turn blue, then turn yellow.

Illustration 37	g06219479
If needed, allow the Truck List page to load.

Payload Settings > List Management > Truck List > Read Error Retry

Illustration 38	g06219499
(4) OK button (6) BACK button

Should the “Read Error Retry?” page appear, the operator can determine whether or not to retry loading the Truck List. To retry, press the OK button (4). Pressing the BACK button (6) returns the operator to the List Management page.

Illustration 39	g06219508
Truck List page (3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (66) ADD button (67) DELETE ROW button (68) List Selection bar (69) Double UP Arrow bar (70) Double DOWN Arrow bar

There are three (3) columns in the Truck List page:

• The Name column shows a list of the names of trucks.

• The ID column shows the corresponding truck’s identification number.

• The Target Weight column shows the corresponding truck’s target weight. The units change based on the “Display Units” and “Weight Units” settings.

The operator can perform the following actions:

• Edit the information of an existing truck entry

• Add a new truck entry

• Delete a truck entry

• Save changes to a truck entry

To modify an existing truck entry, select the intended Truck by pressing either the UP Arrow button (3) or the DOWN Arrow button (5). The intended row will be highlighted with a yellow List Selection Bar (68). Press the OK button (4). The Edit Truck settings page will appear.

Note: Press the Double UP Arrow button (69) to move directly to the top of the list. Press the Double DOWN Arrow button (70) to move directly to the bottom of the list.

Payload Settings > List Management > Truck List > Edit Truck

Illustration 40	g06219518
Edit Truck settings page (4) OK button (6) BACK button (7) HOME button (71) Name EDIT button (72) ID EDIT button (73) Target Weight EDIT button

Illustration 41	g06219531
(4) OK button (6) BACK button (7) HOME button (71) Name EDIT button (74) Keypad BACK button (75) LETTER CASE CHANGE button

1. The existing truck name is visible. Edit the truck name by pressing the Name EDIT button (71). An alphanumeric keypad will appear.

2. Press the LETTER CASE CHANGE button (75) to toggle between upper case and lower case letters.

3. Press the Keypad BACK button (74) to correct an error.

4. Press the OK button (4) when finished. The updated truck name will appear on the edit truck page.

Illustration 42	g06219654
(4) OK button (6) BACK button (7) HOME button (72) ID EDIT button (74) Keypad BACK button

1. The existing truck ID number is visible. Edit the truck ID number by pressing the ID EDIT button (72). A numeric keypad will appear.

2. Press the Keypad BACK button (74) to correct an error.

3. Press the OK button (4) when finished. The updated truck ID will appear on the edit truck page.

Illustration 43	g06219666
(4) OK button (6) BACK button (7) HOME button (73) Target Weight EDIT button (74) Keypad BACK button

1. The existing truck target weight number is visible. Edit the truck target weight by pressing the Target Weight EDIT button (73). A numeric keypad will appear.

2. Press the Keypad BACK button (74) to correct an error.

3. Press the OK button (4) when finished. The updated truck Target Weight will appear on the edit truck page.

Payload Settings > List Management > Truck List > Add Truck

Illustration 44	g06219667
(66) ADD button

1. Add a new truck to the Truck List by pressing the ADD button (66).

Illustration 45	g06219670
“Add Before or After current selection?” settings page (76) Before – UP Arrow button (77) After – DOWN Arrow button

The “Add Before or After current selection?” settings page allows the operator to determine where the newly added truck information would appear on the Truck List page.

Illustration 46	g06219674
(68) List Selection bar

Pressing the Before – UP Arrow button (76) will allow the operator to place the newly added entry above the existing truck highlighted by the List Selection Bar (68).

Pressing the After – DOWN Arrow button (77) will allow the operator to place the newly added entry below the existing truck highlighted by the List Selection Bar (68).

Illustration 47	g06219696
(71) Name EDIT button (72) ID EDIT button (73) Target Weight EDIT button (78) Add Before Navigation Path (79) Add After Navigation Path

Note: The procedure "Add After" is similar to the procedure "Add Before".

Illustration 48	g06219707
"Add Before" settings page (71) Name EDIT button (72) ID EDIT button (73) Target Weight EDIT button (78) Add Before Navigation Path (79) Add After Navigation Path

Press the Name EDIT button (71) to access the Add Before alphanumeric keypad.

Illustration 49	g06219718
(4) OK button (6) BACK button (7) HOME button (71) Name EDIT button (74) Keypad BACK button (75) LETTER CASE CHANGE button (78) Add Before Navigation Path

1. Edit the truck name by pressing the Name EDIT button (71). An alphanumeric keypad will appear.

2. Press the LETTER CASE CHANGE button (75) to toggle between upper case and lower case letters.

3. Press the Keypad BACK button (74) to correct an error.

4. Press the OK button (4) when finished. The updated truck name will appear on the add truck page.

Illustration 50	g06219736
(4) OK button (6) BACK button (7) HOME button (72) ID EDIT button (74) Keypad BACK button (78) Add Before Navigation Path

5. Edit the truck ID number by pressing the ID EDIT button (72). A numeric keypad will appear.

6. Press the Keypad BACK button (74) to correct an error.

7. Press the OK button (4) when finished. The updated truck ID will appear on the add truck page.

Illustration 51	g06219745
(4) OK button (6) BACK button (7) HOME button (73) EDIT button (Target Weight) (74) Keypad BACK button (78) Add Before Navigation Path

8. Edit the truck target weight by pressing the Target Weight EDIT button (73). A numeric keypad will appear.

9. Press the Keypad BACK button (74) to correct an error.

10. Press the OK button (4) when finished. The updated truck Target Weight will appear on the add truck page.

Illustration 52	g06219748
The newly created List Selection Bar (68) and its settings now appear above the previously highlighted truck entry. (68) List Selection Bar (Example: NEW) (80) SAVE button

Note: Now that a new List Selection Bar has been created, the SAVE button (80) will appear. The new List Selection Bar must be saved before leaving the page. For more information, refer to the following section in this manual:

• Saving the Changes

Payload Settings > List Management > Truck List > Delete Truck

Illustration 53	g06219755
Truck List page (4) OK button (6) BACK button (7) HOME button (68) List Selection bar (Example: NEW) (69) Double UP Arrow bar (70) Double DOWN Arrow bar (81) DELETE ROW button

To delete an existing Truck List Selection bar (68) (Example: NEW), select the intended Truck by pressing either the UP Arrow button (3) or the DOWN Arrow button (5). The intended row will be highlighted with a yellow List Selection Bar (68). Press the OK button (4). The Delete Truck settings page will appear.

Note: Press the Double UP Arrow button (69) to move directly to the top of the list. Press the Double DOWN Arrow button (70) to move directly to the bottom of the list.

Illustration 54	g06219761
Delete Truck settings page (4) OK button (6) BACK button

The Delete Truck prompt allows the operator to decide whether or not to delete the selected truck highlighted by the List Selection bar.

The name of the truck, “NEW”, is shown on the Delete Truck prompt to remind the operator which truck entry will be deleted.

1. Press the OK button (4) to delete the information.

2. Press the BACK button (6) to not delete the information and to return to the Truck List page.

Illustration 55	g06219772
The truck listing, “NEW”, has been deleted. (80) SAVE button (81) DELETE ROW button

Note: Now that the List Selection Bar has been deleted, the SAVE button (80) will appear. The deletion must be saved before leaving the page. For more information, refer to the following section in this manual:

• Saving the Changes

Illustration 56	g06219774
(80) SAVE button

Any changes made via Edit, Add, or Delete will not be saved unless the operator presses the SAVE button (80). When the operator presses the SAVE button, the “Save Changes?” settings page will appear.

Illustration 57	g06219776
“Save Changes?” settings page (4) OK button (6) BACK button

1. Press the OK button (4) to save the changes made on the Truck List page.

2. Press the BACK button (6) to not save the changes.

Illustration 58	g06219791
The “Exit without saving?” page will pop-up if the operator attempts to leave the Truck List by pressing Home or Back without first saving the changes. (4) OK button (6) BACK button

3. Pressing the OK button (4) exits the Truck List page and discards all changes.

4. Pressing the BACK button (6) returns the operator to the Truck List.

Rimpull (XE)

Machine > Settings > Rimpull

Note: This feature is only for the following machine models:

• 966M CVT HRC

• 972M CVT HRC

Illustration 59	g06219793
Truck List page (3) UP button (4) OK button (5) DOWN button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Sliding Indicator (82) Rimpull menu button (83) Increment/Decrement bar

1. Press the Machine menu button (1) located on the right side of the Information Display. The Machine menu page will appear.

2. Press the Settings menu button (8). The button will first turn to blue, then turn to yellow. The Settings menu page will appear.

3. Press the UP Arrow button (3) or DOWN Arrow button (5) to scroll to the Rimpull menu button (82). The Menu Sliding Indicator of the Non-Interactive Scroll Bar (10) will move with the page.

4. Press the Rimpull menu button (82). The button will first turn to blue, then turn to yellow. The Rimpull settings page will appear.

5. Use the Increment/Decrement bar (83) to adjust the “% Max Rimpull” setting. Press the PLUS (+) button on the right end of the Increment/Decrement bar to increase a number. Press the MINUS (-) button the left end of the Increment/Decrement bar to decrease a number.

6. When an intended number appears, press the OK button (4) to set. The newly set number will appear in white text.

7. Press the BACK button (6) to return to the previous menu.

8. Press the HOME button (7) to return to the Home page (Performance Page).

Functions

Machine > Settings > Functions

Note: The Functions menu button will be visible only if its submenu items are shown. The submenus are visible provided certain configurations are installed.

Illustration 60	g06219795
(3) UP Arrow button (4) OK button (5) DOWN Arrow button (6) BACK button (7) HOME button (10) Non-Interactive Scroll Bar with Menu Sliding Indicator (84) Functions menu button

1. Press the Machine button (1) located on the right side of the Information Display. The Machine menu page will appear.

2. Press the Settings menu button (9). The button will first turn to blue, then turn to yellow. The Settings menu page will appear.

3. Press the Functions menu button (84). The button will first turn to blue, then turn to yellow. The Functions settings page will appear.

The Functions settings are:

• 2^nd (Second) Steer Test

• Fan Purge

• Service Brake Test (XE)

2nd Steer Test

Machine > Settings > Functions > 2nd Steer Test

Note: This function is visible if the Steering Configuration is Electro-Hydraulic or is by Joystick, or if the Secondary Steering Pump is installed.

Illustration 61	g06219806
Functions settings page (6) BACK button (7) HOME button (85) 2nd Steer Test button

1. Press the 2^nd Steer Test button (85). The button will first turn blue. The button will advance to the right and turn green.

2. To turn off 2^nd Steer Test, press the button again. The button will turn blue. The button will return to the left OFF position, and then turn gray.

3. Press the BACK button (6) to return to the previous menu.

4. Press the HOME button (7) to return to the HOME page.

Fan Purge

Machine > Settings > Functions > Fan Purge

Note: The function is visible if the Engine Fan Reversing feature is enabled.

Illustration 62	g06219810
Functions settings page (6) BACK button (7) HOME button (86) Fan Purge button

1. Press the Fan Purge button (86) to activate the Fan Purge.

2. The button will turn green for the purge cycle, and remain green for the entire cycle.

3. Press the BACK button (6) to return to the previous menu.

4. Press the HOME button (7) to return to the HOME page.

Service Brake Test (XE)

Machine > Settings > Functions > Service Brake Test

Note: The XE Functions page includes the Service Brake Test switch.

Illustration 63	g06219818
Functions settings page (6) BACK button (7) HOME button (87) Service Brake Test switch

1. To turn ON the Service Brake Test, press the Service Brake Test button (87). The button will first be highlighted in blue. The button will then advance to the right and turn the color green.

2. The Service Brake Test will indicate that it is either “Active”, “Inactive”, or “Aborted”. If the test is aborted, the test will inform the operator to “Retest Service Brakes”.

3. To turn OFF the Service Brake Test, press the Service Brake Test button (87) again. The button will first be highlighted in blue. The button will then return to the left (OFF position) and turn gray in color.

4. Press the BACK button (6) to return to the previous menu.

5. Press the HOME button (7) to return to the HOME page.

Auto Differential Lock

Machine > Settings > Auto Differential Lock

Note: This feature is visible provided that the feature is installed.

Illustration 64	g06219944
(4) OK button (6) BACK button (7) HOME button (88) Auto Differential Lock menu button (89) Auto Differential Lock menu button group (Enabled or Disabled)

1. Press the Machine button (1) located on the right side of the Information Display. The Machine menu page will appear.

2. Press the Settings menu button (9). The button will first turn to blue, then turn to yellow. The Settings menu page will appear.

3. Press the Auto Differential Lock menu button (88). The button will first turn to blue, then turn to yellow. The Auto Differential Lock settings page will appear.

4. Press the intended menu button (Enabled or Disabled) in the menu button group (89). Press the OK button (4) to set. The selected button will first turn to blue, then turn to yellow. A check mark will also appear in the selected menu button.

5. Press the BACK button (6) to return to the previous menu.

6. Press the HOME button (7) to return to the HOME page.

Economy Mode

Machine > Settings > Economy Mode

Illustration 65	g06219968
(4) OK button (6) BACK button (7) HOME button (90) Economy Mode menu button (91) Economy Mode menu button group (Off or On)

1. Press the Machine button (1) located on the right side of the Information Display. The Machine menu page will appear.

2. Press the Settings menu button (9). The button will first turn to blue, then to yellow. The Settings menu page will appear.

3. Press the Economy Mode menu button (90). The button will turn to blue, then to yellow. The Economy Mode settings page will appear.

4. Press the intended menu button (Off or On) in the menu button group (91). Press the OK button (4) to set. The selected button will be highlighted in yellow. A check mark will also appear in the selected menu button.

5. Press the BACK button (6) to return to the previous menu.

6. Press the HOME button (7) to return to the HOME page.