| |
| Illustration 1 | g06217963 |
| (1) DISPLAY Hotkey button | |
The DISPLAY button allows the operator to adjust the Display’s screen brightness, to select a specific language and to select a specific measuring unit (Metric or English). The DISPLAY button also allows the operator to locate and read the Software License Info menu.
Press the DISPLAY button (1) to view and access the following Display menu settings:
- Brightness
- Language
- Units
- Clock
- Software License Info (Information)
| |
| Illustration 2 | g06217980 |
|
(2) Display menu buttons
(3) Non-Interactive Scroll Bar with Sliding Indicator (4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button | |
Pressing the UP Arrow button (4) or the DOWN Arrow button (6) will scroll the menu button list. In this example, the Sliding Indicator of the Non-Interactive Scroll Bar (3) has moved from the top of the list to the bottom of the list, where the "Software License Info" button is now visible and accessible.
Display > Brightness
| |
| Illustration 3 | g06217994 |
| (9) Screen Brightness menu button | |
- Press the DISPLAY button located on the right side of the Information Display. The menu page will appear.
- Press the Screen Brightness menu button (9) on menu page. The button will turn first to blue, then to yellow. Either the Day Mode Brightness settings page or the Night Mode Brightness settings page will appear.
Show/hide table
Illustration 4 g06218005 (7) BACK button
(8) HOME button
(10) Brightness Screen – DAY Mode icon
(11) Increment/Decrement Bar (MINUS (-) arrow button)
(12) Increment/Decrement Bar (PLUS (+) arrow button)
(13) Brightness Screen – NIGHT Mode icon - The brightness of the Information Display is adjustable by pressing either end of the Increment Bar.
- Increase the brightness of the Information Display by pressing the PLUS (+) arrow button (12) on the right end of the Increment/Decrement Bar.
- Decrease the brightness of the Information Display by pressing the MINUS (-) arrow button (11) on the left end of the Increment/Decrement Bar.
When NONE of the following are ON, the Display and cab lights will enter DAY mode:
- Headlight, marker lights
- Work lights
- Long-distance lights
When ANY of the following are ON, the Display and cab lights will enter NIGHT mode:
- Headlight, marker lights
- Work lights
- Long-distance lights
Press the BACK button (7) to return to the previous page.
Press the HOME button (8) to return to the Home page (Performance Page).
Display > Language
The Language menu button (14) is used to access the Language menu display and to change the display’s language to one that the operator prefers.
Note: English is the default language.
| |
| Illustration 5 | g06268292 |
|
(3) Non-Interactive Scroll Bar with Sliding Indicator
(4) UP Arrow button (5) OK button (6) DOWN Arrow button (7) BACK button (8) HOME button (14) Language Menu button | |
- Press the DISPLAY button located on the right side of the Information Display. The menu page will appear.
- Press the Language menu button (14). The button will turn first to blue, then to yellow. Press the OK button (5). The Language menu list page will appear.
- Use the UP Arrow button (4) or the DOWN Arrow button (5) to scroll through the list of languages and select a preferred language. The selection will highlight in yellow with a check mark. The Menu Sliding Indicator on the Non-Interactive Scroll Bar (3) will scroll with the screen.
- Press the OK button (5) to set.
Press the BACK button (7) to return to the previous page.
Press the HOME button (8) to return to the Home page (Performance Page).
Display > Units
Note: Reference Machine > Settings > Payload if attempting to find “lb x 1000” or “Tons” settings. If “English” is selected, the Weight Units will always set to “Tons” by default.
- View the parameter values in preferred units by changing the Information Display’s Units settings.
- The selection of preferred Units is limited to “English” and “Metric.”
The Information Display will convert the system values to the units selected by the operator. The Information Display will also add the appropriate unit abbreviation for each value.
| |
| Illustration 6 | g06218059 |
|
(5) OK button
(7) BACK button (8) HOME button (15) Units menu button | |
- Press the DISPLAY button located on the right side of the Information Display. The menu page will appear.
- On the Display page, press the Units menu button (15). The button will turn first to blue, then to yellow. The Units menu page will appear.
- Select either “English” or “Metric” by pressing the corresponding menu button. The selected menu button will highlight in blue, then in yellow and be designated with a black check mark.
Note: The Display will convert the system values to the units selected by the operator. The Display will also add the appropriate Unit abbreviation for each value. Press the OK button (5) to set.
Press the BACK button (7) to return to the previous page.
Press the HOME button (8) to return to the Home page (Performance Page).
Display > Clock
The clock appears in the lower left-hand corner of the Information Banner.
Note: The clock will not appear in the Information Banner if the Payload Banner is visible. Refer to the section "Rear Camera (If Installed)".
| |
| Illustration 7 | g06218080 |
|
(16) Clock Menu button
(17) Clock display (Example: 12 hour time) | |
| |
| Illustration 8 | g06218085 |
|
Clock settings page with Auto/Manual Format button (20) switched OFF and the Hours Display Format button set to "12". (17) Clock display (18) AM/PM Display Format button (19) "Hours" Increment/Decrement Bar (20) Auto/Manual Format button (21) "Minutes" Increment/Decrement Bar (22) "Hours" Display Format button | |
| |
| Illustration 9 | g06218088 |
|
Clock settings page where the Auto/Manual Format button (20) is ON. The Hours Display Format button is set to "12". (20) Auto/Manual Format button | |
| |
| Illustration 10 | g06218092 |
|
Clock settings page where the Hours Display Format button (22) is set to "24". (17) Clock display (22) Hour Display Format button | |
- Press the Clock menu button (16). The button will turn first to blue, then to yellow. The Clock settings page will appear.
- To allow the clock to set automatically, press the Auto/Manual Format button (20). When the button moves to the right side and appears in green, the Automatic Time Setting feature is ON. The clock cannot be set manually unless the Auto/Manual Format button is pressed, moving to the left and appearing in gray.
- To adjust the Hours, press either the MINUS (-) Arrow button or the PLUS (+) Arrow button. The numbers will appear in yellow during setting. The numbers will appear in white when set.
- To adjust the Minutes, press either the MINUS (-) Arrow button or the PLUS (+) Arrow button. The numbers will appear in yellow during setting. The numbers will appear in white when set.
Note: Neither the Hours setting or the Minutes setting can be cycled through. For example, when scrolling the minutes up to “59”, the operator cannot continue to scroll up to get back to “0”. The operator would have to scroll back down the list to get to “0”.
- To set the Hours Display Format to 12 hours (Example: 7:00 AM and 7:00 PM), press the Number 12 - Hours Display Format button (22). The button will highlight in green.
- To set the Hours Display Format to 24 hours (Example: 700 hours and 1900 hours), press the Number 24 - Hours Display Format button (22). The button will highlight in green.
Note: If the Hours Display Format is set to 24 hours, the AM/PM Display Format button will not be visible. The clock in the Information Banner will also not show the time as AM or PM.
- To set the AM/PM Display Format, press the applicable button. The button will highlight in green.
Press the BACK button (7) to return to the previous page.
Press the HOME button (8) to return to the Home page (Performance Page).
Display > Software License Info
| |
| Illustration 11 | g06218100 |
|
(4) UP Arrow button
(23) Software License Info menu button | |
| |
| Illustration 12 | g06218103 |
|
(3) Non-Interactive Scroll Bar with Menu Sliding Indicator
(4) UP Arrow button (6) DOWN Arrow button (7) BACK button (8) HOME button | |
- Press the Display button (1) on the right side of the Display. The menu page will appear.
- Press the Software License Info button (23). The button will highlight in blue, then in yellow. The Software License pages will appear.
- Press the UP Arrow button (4) or the DOWN arrow button (6) to read the pages of the License Agreement. The Menu Sliding Indicator of the Non-Interactive Scroll Bar (3) will move accordingly.
Press the BACK button (7) to return to the previous page.
Press the HOME button (8) to return to the Home page (Performance Page).