Counterweight Sections - Remove and Install
Removal Procedure
- Position the counterweight frame into the stored position. Install locking bolt (1) .
Show/hide table
Illustration 1 | g03831661 |
- Attach a suitable lifting device to counterweight (2). The weight of counterweight (2) is approximately 787 kg (1735 lb).
Show/hide table
Illustration 2 | g03831666 |
- Loosen nut (3) and bolt (4) .
Show/hide table
Illustration 3 | g03831667 |
- Remove rod assembly (5) .
- Remove counterweights (2) .
- Use the suitable lifting device in order to remove counterweight (5). Repeat this step for the remaining counterweights (5) .
- Repeat Steps 2 through 6 for the removal of the counterweights on the opposite side.
Installation Procedure
- Install counterweight (2) in the reverse order of removal.
Caterpillar Information System:
Check Lift Arm Welds on R3000H Load Haul Dump Machines{6107} Check Lift Arm Welds on R3000H Load Haul Dump Machines{6107}
Check the Tilt Cylinder Line Relief Valve on R3000H Load Haul Dump Machines{5117} Check the Tilt Cylinder Line Relief Valve on R3000H Load Haul Dump Machines{5117}
Check the Tilt Cylinder on Certain R1700G and R2900G Load Haul Dump Machines{5104} Check the Tilt Cylinder on Certain R1700G and R2900G Load Haul Dump Machines{5104}
PL83 and PL87 Pipelayers Machine Systems Seat - Remove and Install
PL83 and PL87 Pipelayers Machine Systems Counterweight Cylinder - Remove and Install
527 Track-Type Skidder Reference Material
New Steering Cylinders With Position Sensors are Now Available on Certain Motor Graders {4303, 7620} New Steering Cylinders With Position Sensors are Now Available on Certain Motor Graders {4303, 7620}
CB64B, CB66B and CB68B Asphalt Compactors Machine Systems Case Drain Flow for Piston Motor (Vibratory) - Test
CW34 Pneumatic Compactor Monitoring System
2015/05/14 Gear Inspection Should Be Performed When Replacing the Torsional Coupler on Certain 14M and 16M Motor Graders {3063}
725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735C, 740 Ejector, 740C Ejector, 745 and 745C Articulated Trucks Cat® Production Measurement Application Determining Diagnostic Trouble Codes
CW34 Pneumatic Compactor Air Compressor Oil - Change
Procedure to Install Machine Automation System on R1600H Load Haul Dump Machines {7000, 7600} Procedure to Install Machine Automation System on R1600H Load Haul Dump Machines {7000, 7600}
PL83 and PL87 Pipelayers Machine Systems Fairlead Sheave - Remove and Install
C2.2 Engines For Caterpillar Built Machines Glow Plug Starting Aid - Test
24M Motor Grader Rim - Inspect
C2.2 Engines For Caterpillar Built Machines Injector Solenoid - Test
415F2 and 427F2 Backhoe Loaders Engine Supplement Radiator, Fuel Cooler, After Cooler, and Hydraulic and XMSN Oil Cooler - Remove and Install
793F Off-Highway Truck (Command For Hauling) Machine Systems Front Wheel Bearings - Remove
777G Off-Highway Truck Steering System Steering Shaft (Cover Plate) - Check and Adjust
793F Off-Highway Truck (Command For Hauling) Machine Systems Front Wheel Bearings - Install
M314F, M316F, M318F, M320F and M322F Wheeled Excavator and Material Handler Machine Systems Piston Pump (Fan) - Disassemble
C13, C15, and C18 Engines for Caterpillar Built Machines Electronic Service Tool Does Not Communicate
Installation of the 435-9232 Air Conditioner Kit (Conversion) {1408, 7304, 7309, 7320, 7320, 734D} Installation of the 435-9232 Air Conditioner Kit (Conversion) {1408, 7304, 7309, 7320, 7320, 734D}