Front Wheel Bearings - Remove
Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 138-7576 | Link Bracket | 3 |
| B | 154-6182 | Forcing Bolt | 2 |
| C | 154-6181 | Forcing Bolt | 2 |
Start By:
- Remove the wheel, the brake, and the suspension cylinder.
- Remove bolts (1). Use Tooling (B) to remove cover (2) .
Show/hide table
 | |
| Illustration 1 | g02770859 |
- Remove bolts (3), retainer (4), cover (5), O-ring seal (6), and O-ring seals (7) .
Show/hide table
 | |
| Illustration 2 | g01953491 |
- Remove bolts (8) from speed sensor (9) .
Show/hide table
 | |
| Illustration 3 | g03831879 |
- Loosen grommet assembly (10) from harness assembly (11) .
Note: Note the position of the green tape that is present on harness assembly (11) for installation purposes.
Show/hide table
 | |
| Illustration 4 | g03831849 |
Show/hide table
| NOTICE |
|---|
Do not attempt to loosen the grommet assembly unless the bolts that secure the speed sensor have been removed. Damage to the harness can occur. |
- Pull speed sensor assembly (9) from the wheel assembly enough to disconnect speed sensor assembly (9) from harness assembly (11) .
Show/hide table
 | |
| Illustration 5 | g03831885 |
- Remove bolts (12). Remove retainer (13). Remove shims (14) .
Show/hide table
 | |
| Illustration 6 | g03831892 |
- Use Tooling (A) and a suitable lifting device in order to remove wheel assembly (15). The weight of wheel assembly (15) is approximately 916 kg (2020 lb). If necessary, use a suitable lifting device to remove spacer ring (16). The weight of spacer ring (16) is approximately 77 kg (170 lb).
Show/hide table
 | |
| Illustration 7 | g03831896 |
- Use two people in order to remove bearing cone (17). The weight of bearing cone (17) is approximately 32 kg (70 lb).
Show/hide table
 | |
| Illustration 8 | g03831897 |
- Remove bearing cup (18) .
Show/hide table
 | |
| Illustration 9 | g03831901 |
- Turn over the wheel housing.
- Remove Duo - Cone seal (19). Remove bearing cup (20) .
Show/hide table
 | |
| Illustration 10 | g03831909 |
- Remove Duo - Cone seal (21) .
- Remove bearing cone (22). The weight of bearing cone (22) is approximately 53 kg (116 lb).
Show/hide table
 | |
| Illustration 11 | g03831911 |
- Remove Duo - Cone seal (23) .
- Use Tooling (C) to remove retainer (24) from the brake hub.
Show/hide table
 | |
| Illustration 12 | g03831913 |
- Remove Duo - Cone seal (25). Remove O-ring seal (26) from retainer (24) .
Show/hide table
 | |
| Illustration 13 | g03831914 |
Caterpillar Information System:
415F2 and 427F2 Backhoe Loaders Engine Supplement Radiator, Fuel Cooler, After Cooler, and Hydraulic and XMSN Oil Cooler - Remove and Install
C2.2 Engines For Caterpillar Built Machines Injector Solenoid - Test
24M Motor Grader Rim - Inspect
C2.2 Engines For Caterpillar Built Machines Glow Plug Starting Aid - Test
PL83 and PL87 Pipelayers Machine Systems Fairlead Sheave - Remove and Install
Procedure to Install Machine Automation System on R1600H Load Haul Dump Machines {7000, 7600} Procedure to Install Machine Automation System on R1600H Load Haul Dump Machines {7000, 7600}
PL83 and PL87 Pipelayers Machine Systems Counterweight Sections - Remove and Install
Check Lift Arm Welds on R3000H Load Haul Dump Machines{6107} Check Lift Arm Welds on R3000H Load Haul Dump Machines{6107}
Check the Tilt Cylinder Line Relief Valve on R3000H Load Haul Dump Machines{5117} Check the Tilt Cylinder Line Relief Valve on R3000H Load Haul Dump Machines{5117}
Check the Tilt Cylinder on Certain R1700G and R2900G Load Haul Dump Machines{5104} Check the Tilt Cylinder on Certain R1700G and R2900G Load Haul Dump Machines{5104}
PL83 and PL87 Pipelayers Machine Systems Seat - Remove and Install
PL83 and PL87 Pipelayers Machine Systems Counterweight Cylinder - Remove and Install
777G Off-Highway Truck Steering System Steering Shaft (Cover Plate) - Check and Adjust
793F Off-Highway Truck (Command For Hauling) Machine Systems Front Wheel Bearings - Install
M314F, M316F, M318F, M320F and M322F Wheeled Excavator and Material Handler Machine Systems Piston Pump (Fan) - Disassemble
C13, C15, and C18 Engines for Caterpillar Built Machines Electronic Service Tool Does Not Communicate
Installation of the 435-9232 Air Conditioner Kit (Conversion) {1408, 7304, 7309, 7320, 7320, 734D} Installation of the 435-9232 Air Conditioner Kit (Conversion) {1408, 7304, 7309, 7320, 7320, 734D}
2015/05/15 Cylinder Head And Spacer Plate Gasket Failures On Certain Machine Engines {1100, 1201}
2015/05/15 Cylinder Head And Spacer Plate Gasket Failures On Certain Engines {1100, 1201}
CB64B, CB66B and CB68B Asphalt Compactors Machine Electronic Control System Sensor Signal (Analog, Active) - Test
120K Series 2 Motor Grader Maintenance Interval Schedule
2015/05/12 A Longer A/C Condenser Hose Is Available For 272D, 272D XHP Skid Steer Loader, 297D, 297D XHP Multi Terrain Loader And 299D, 299D XHP Compact Terrain Loader {1808, 7320}
140K Series 2 Motor Grader Maintenance Interval Schedule
2015/05/06 Some Reman Torque Convertors Require an Additional Valve {3101, 3180}