PM-200 Cold Planer Caterpillar


Track Drive Planetary Oil - Change

Usage:

PM-200 P1C

------ WARNING! ------

Hot oil and components can cause personal injury.

Do not allow hot oil or components to contact skin.

----------------------


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.

Dispose of all fluids according to local regulations and mandates.





    Illustration 1g03433037

  1. Position the final drive so that filler plug (1) will be horizontal to the ground. Plug (2) will be at the bottom.

  1. Remove the two plugs. Allow the oil to drain into a suitable container. The capacity of each final drive is 0.9 L (0.24 US gal).

  1. Clean drain plug (2) and install drain plug (2) .

  1. Add oil through the opening for filler plug (1) until the level at the bottom of the opening is reached.

  1. Clean filler plug (1) and install plug (1) .

  1. Repeat Steps 1 to 5 for the other tracks.

Caterpillar Information System:

PM-200 Cold Planer Track Drive Planetary Oil Level - Check
834K Wheel Dozer and 836K Landfill Compactor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} 834K Wheel Dozer and 836K Landfill Compactor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
PM-200 Cold Planer Track Shoe Bolts - Tighten
PM-200 Cold Planer Track Tension - Check/Adjust
PM-200 Cold Planer Tracks - Inspect
966M Series XE and 972M Series XE Wheel Loaders Rated Load
CB34B, CB34B XW, CC34B and CB36B Vibratory Utility Compactors Machine Systems Vibratory Valve - Remove and Install
CB34B, CB34B XW, CC34B and CB36B Vibratory Utility Compactors Machine Systems Piston Pump (Propel) - Remove and Install
CB22B, CB24B, CB32B and CC24B Vibratory Utility Compactors Propel System Piston Motor (Drum Propel)
773E and 777D Off-Highway Truck/Tractor Object Detection System (Two Cameras) MID 134 - CID 3319 - FMI 12
773E and 777D Off-Highway Truck/Tractor Object Detection System (Two Cameras) MID 134 - CID 3319 - FMI 09
793F Series AC Off-Highway Truck Power Train Power Generator - Remove and Install
14L Motor Grader Machine Systems Bank Valve - Assemble - Rear Frame
14L Motor Grader Machine Systems Bank Valve - Disassemble - Rear Frame
14L Motor Grader Machine Systems Bank Valve - Install - Rear Frame
Cat® Detect Proximity Awareness Onboard System Tool Button Display
2013/09/24 A New Ether Cylinder O-ring is Now Used on All Caterpillar Products {1456}
Cat® Detect Proximity Awareness Onboard System Proximity Alarming
PM-200 Cold Planer Steering Linkage - Lubricate
PM-200 Cold Planer Steering Cylinder Ends - Lubricate
PM-200 Cold Planer Upper Conveyor Deflectors (Second Stage) - Inspect/Replace
988K XE Wheel Loader Machine Systems Ride Control Valve - Assemble
AS4173 Asphalt Screed Machine Systems Tamper Bar - Check and Adjust
2014/02/12 New Installation Kits are now Available for Cat® MineStar Fleet Onboard and Cat® MineStar Health Systems {7605}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.