Bank Valve - Install - Rear Frame
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 311-1362 | Vacuum Cap | 1 |
| B | 138-7573 | Link Bracket | 2 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Attach Tooling (B) and a suitable lifting device in order to install bank valve (20). The weight of bank valve (20) is approximately
50 kg (110 lb) .Show/hide table
Illustration 2 g01430691 Show/hide table
Illustration 3 g01430692 - Install bolts (19) and bolts (18).
Show/hide table
Illustration 4 g03434118 - Connect tube assembly (17). Connect tube assembly (16). Connect tube assemblies (15).
Show/hide table
Illustration 5 g01430627 - Connect fitting (14).
Show/hide table
Illustration 6 g03434119 - Connect fitting (13). Connect hose assemblies (12). Connect hose assemblies (11).
Show/hide table
Illustration 7 g01430618 - Install tube assembly (10). Install tube assembly (9). Connect harness assemblies (8) and harness assemblies (7). Install tube assemblies (6) and tube assemblies (5).
Show/hide table
Illustration 8 g01430613 - Install blocks (4). Install clip (3). Connect harness assemblies (2).
Show/hide table
Illustration 9 g01430501 - Install cover (1). Repeat this step for the cover on the opposite side.
Show/hide table
Illustration 10 g01368952 - Remove Tooling (A).
- Fill the hydraulic tank. Refer to Operation and Maintenance Manual, "Capacities - Refill".
Show/hide table
| |
| Illustration 1 | g01430704 |
Caterpillar Information System:
14L Motor Grader Machine Systems Bank Valve - Disassemble - Rear Frame
14L Motor Grader Machine Systems Bank Valve - Assemble - Rear Frame
PM-200 Cold Planer Track Drive Planetary Oil - Change
PM-200 Cold Planer Track Drive Planetary Oil Level - Check
834K Wheel Dozer and 836K Landfill Compactor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} 834K Wheel Dozer and 836K Landfill Compactor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
PM-200 Cold Planer Track Shoe Bolts - Tighten
PM-200 Cold Planer Track Tension - Check/Adjust
PM-200 Cold Planer Tracks - Inspect
966M Series XE and 972M Series XE Wheel Loaders Rated Load
CB34B, CB34B XW, CC34B and CB36B Vibratory Utility Compactors Machine Systems Vibratory Valve - Remove and Install
CB34B, CB34B XW, CC34B and CB36B Vibratory Utility Compactors Machine Systems Piston Pump (Propel) - Remove and Install
CB22B, CB24B, CB32B and CC24B Vibratory Utility Compactors Propel System Piston Motor (Drum Propel)
Cat® Detect Proximity Awareness Onboard System Tool Button Display
2013/09/24 A New Ether Cylinder O-ring is Now Used on All Caterpillar Products {1456}
Cat® Detect Proximity Awareness Onboard System Proximity Alarming
PM-200 Cold Planer Steering Linkage - Lubricate
PM-200 Cold Planer Steering Cylinder Ends - Lubricate
PM-200 Cold Planer Upper Conveyor Deflectors (Second Stage) - Inspect/Replace
988K XE Wheel Loader Machine Systems Ride Control Valve - Assemble
AS4173 Asphalt Screed Machine Systems Tamper Bar - Check and Adjust
2014/02/12 New Installation Kits are now Available for Cat® MineStar Fleet Onboard and Cat® MineStar Health Systems {7605}
2013/12/06 New Exhaust Shield Now Used on Certain R1700G Load Haul Dump Machines {1067}
2013/09/20 New Procedure to Flash LADAR Firmware Now Used on MINEGEM Equipped Machines {7600, 7615}
PM-200 Cold Planer Engine Oil and Filter - Change