Ride Control Valve - Assemble
- Install plugs (33), plugs (34) and the O-ring seals.
Show/hide table
Illustration 2 g03433556 Show/hide table
Personal injury can result from being struck by parts propelled by a released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to release the spring force.
- Install washer (32), spring (31), plug (30) and the O-ring seal.
Show/hide table
Illustration 3 g03433240 Show/hide tableImproper assembly of parts that are spring loaded can cause bodily injury.
To prevent possible injury, follow the established assembly procedure and wear protective equipment.
- Install stem (26), washer (27), spring (28), plug (29) and the O-ring seal.
Show/hide table
Illustration 4 g03433219 Show/hide tableImproper assembly of parts that are spring loaded can cause bodily injury.
To prevent possible injury, follow the established assembly procedure and wear protective equipment.
- Install stem (20), spring (21), O-ring seal and seat (22), valve (23), O-ring seals (24), and valve (25).
Show/hide table
Illustration 5 g03433136 - Install valve assembly (19).
Show/hide table
Illustration 6 g03432560 - Install O-ring seal (17), back up ring (18) and valve stem (16).
Show/hide table
Illustration 7 g03432540 Show/hide tableImproper assembly of parts that are spring loaded can cause bodily injury.
To prevent possible injury, follow the established assembly procedure and wear protective equipment.
- Install housing (11), bolts (12), retainer (13), spring (14), plug (15) and the O-ring seal.
Show/hide table
Illustration 8 g03432529 - Install back up rings (10), O-ring seals (9), coil assembly (8), and nut (7).
Show/hide table
Illustration 9 g03432522 - Install valve assembly (6).
Show/hide table
Illustration 10 g03432515 - Install back up rings (5), O-ring seals (4), coil assembly (3), and nut (2).
Show/hide table
Illustration 11 g03434109 - Install valve assembly (1).
Show/hide table
| |
| Illustration 1 | g03433778 |
Caterpillar Information System:
PM-200 Cold Planer Upper Conveyor Deflectors (Second Stage) - Inspect/Replace
PM-200 Cold Planer Steering Cylinder Ends - Lubricate
PM-200 Cold Planer Steering Linkage - Lubricate
Cat® Detect Proximity Awareness Onboard System Proximity Alarming
2013/09/24 A New Ether Cylinder O-ring is Now Used on All Caterpillar Products {1456}
Cat® Detect Proximity Awareness Onboard System Tool Button Display
14L Motor Grader Machine Systems Bank Valve - Install - Rear Frame
14L Motor Grader Machine Systems Bank Valve - Disassemble - Rear Frame
14L Motor Grader Machine Systems Bank Valve - Assemble - Rear Frame
PM-200 Cold Planer Track Drive Planetary Oil - Change
PM-200 Cold Planer Track Drive Planetary Oil Level - Check
834K Wheel Dozer and 836K Landfill Compactor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} 834K Wheel Dozer and 836K Landfill Compactor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
AS4173 Asphalt Screed Machine Systems Tamper Bar - Check and Adjust
2014/02/12 New Installation Kits are now Available for Cat® MineStar Fleet Onboard and Cat® MineStar Health Systems {7605}
2013/12/06 New Exhaust Shield Now Used on Certain R1700G Load Haul Dump Machines {1067}
2013/09/20 New Procedure to Flash LADAR Firmware Now Used on MINEGEM Equipped Machines {7600, 7615}
PM-200 Cold Planer Engine Oil and Filter - Change
966M Series XE and 972M Series XE Wheel Loaders Plate Locations and Film Locations
PM-200 Cold Planer Engine Oil Level - Check
PL83 and PL87 Pipelayers Engine Supplement Fuel Filter Base and Priming Pump - Remove and Install
PM-200 Cold Planer Engine Oil Sample - Obtain
C7.1 Industrial Engine Turbocharger Exhaust Temperature Sensor
2013/10/09 Front Suspension Group Has Been Improved on Certain Off-Highway Trucks {7201}
PM-200 Cold Planer Fuel System - Prime