Cylinder Head
Show/hide table
图 1 | g03330706 |
螺栓拧紧顺序 |
Show/hide table
346-0485 缸盖总成 的技术规格     | |||
项目     | 数量     | 零件     | 技术规格说明     |
1     | 26     | 290-6884 缸盖紧固件总成     | 按照以下步骤拧紧缸盖螺栓: 请参阅图 1 中的缸盖螺栓拧紧顺序。 装配前,使用清洁的发动机机油轻轻润滑螺栓螺纹。 1. 按照数字顺序,将螺栓 1 至螺栓 26 拧紧至扭矩为 160 ± 15 N·m (118 ± 11 lb ft)。 2. 按照数字顺序,再次将螺栓 1 至螺栓 26 拧紧至扭矩为 160 ± 15 N·m (118 ± 11 lb ft)。 3. 在螺栓 1 至螺栓 26 上做一个标记。 按数字顺序将螺栓 1 到螺栓 26 拧紧 90 度(1/4 圈)。 4. 松开螺栓 1 至螺栓 26,直到螺栓头下方的垫圈松动。 5. 按照数字顺序,将螺栓 1 至螺栓 26 拧紧至扭矩为 160 ± 15 N·m (118 ± 11 lb ft)。 6. 按照数字顺序,再次将螺栓 1 至螺栓 26 拧紧至扭矩为 160 ± 15 N·m (118 ± 11 lb ft)。 7. 在螺栓 1 至螺栓 26 上做一个标记。 按数字顺序将螺栓 1 到螺栓 26 拧紧 90 度(1/4 圈)。 8. 按照数字顺序,将螺栓 27 至螺栓 32 拧紧至扭矩为 28 ± 7 N·m (21 ± 5 lb ft)。     |
2     | 6     | 9X-6000 螺栓     | |
-     | -     | -     | 新缸盖的高度为 163.00 ± 0.15 mm (6.417 ± 0.006 in)。     |
Show/hide table
图 2 | g03330707 |
Show/hide table
项目     | 数量     | 零件     | 技术规格说明     |
3     | 5     | 8M-5860 杯塞     | 安装前,将 Loctite 11358 涂抹到杯塞的孔上。     |
4     | 6     | 3B-0623 杯塞     | 安装前,将 Loctite 11358 涂抹到杯塞的孔上。     |
5     | 3     | 8M-5860 杯塞     | 安装前,将 Loctite 11358 涂抹到杯塞的孔上。     |
6     | 1     | 8M-5860 杯塞     | 安装前,将 Loctite 11358 涂抹到杯塞的孔上。     |
7     | 6     | 310-7258 O 形密封圈     | 装配前,向孔上涂覆清洁的发动机机油。     |
8     | 6     | 310-7259 O 形密封圈     | 装配前,向孔上涂覆清洁的发动机机油。     |
9     | 6     | 325-6575 喷油器套筒     | 装配前,向喷油器衬套外表面上涂覆距离为 (H) 的绿色 Loctite 620。     |
E     | -     | -     | 杯塞 (3) 的安装长度为 1.25 ± 0.25 mm (0.049 ± 0.010 in)。     |
F     | -     | -     | 杯塞 (4) 的安装长度为 3.75 ± 0.50 mm (0.148 ± 0.020 in)。     |
G     | -     | -     | 杯塞 (5) 的安装长度为 1.00 ± 0.50 mm (0.039 ± 0.020 in)。     |
Caterpillar Information System:
966H Wheel Loader and 972H Wheel Loader Electrohydraulic System Pilot Oil Accumulator (Dead Engine, Lift Arm Lower) - Test and Charge
R1300G Load Haul Dump Cooling System Coolant Extender (ELC) - Add
C13, C15, and C18 Tier 4 Final Engines Cylinder Head Valves
R1300G Load Haul Dump Cooling System Coolant (DEAC) - Change
R1300G Load Haul Dump Cooling System Level - Check
SH-56B Felling Head Felling Head Grapple Arm Spring - Disassemble
422F, 428F, 432F, 434F and 444F Backhoe Loaders Cooling System Coolant Sample (Level 2) - Obtain
422F, 428F, 432F, 434F and 444F Backhoe Loaders Cooling System Coolant Sample (Level 1) - Obtain
773G and 775G Quarry Trucks Chassis Electronic Control System MID 087 - CID 0247 - FMI 09
422F, 428F, 432F, 434F and 444F Backhoe Loaders Cooling System Coolant Level - Check
422F, 428F, 432F, 434F and 444F Backhoe Loaders Cooling System Coolant (ELC) - Change
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Parking Brake - Remove and Install
2013/08/21 Calculating Cylinder Liner Projection for 3500, 3500B, 3500C, and G3500 Engines {1201, 1216}
422F, 428F, 432F, 434F and 444F Backhoe Loaders Window Washer Reservoir - Fill
422F, 428F, 432F, 434F and 444F Backhoe Loaders Wheel Nut Torque - Check
2470C, 2570C and 2670C Wheel Feller Bunchers IQAN Monitoring ; Control System Diagnostic Capabilities
773G and 775G Quarry Trucks Chassis Electronic Control System MID 087 - CID 0248 - FMI 09
773G and 775G Quarry Trucks Chassis Electronic Control System MID 087 - CID 0420 - FMI 03
773G and 775G Quarry Trucks Chassis Electronic Control System MID 087 - CID 0420 - FMI 05
773G and 775G Quarry Trucks Chassis Electronic Control System MID 087 - CID 0420 - FMI 06
Installation Procedure for Front Heated Window Glass on Certain M, M Series 2, and M Series 3 Motor Graders {1408, 7305, 7310} Installation Procedure for Front Heated Window Glass on Certain M, M Series 2, and M Series 3 Motor Graders {1408, 7305, 7310}
Correct Combinations of Connecting Rods Allowed in Remanufactured Cylinder Packs for Certain C13 Engines{1218, 1225, 1239} Correct Combinations of Connecting Rods Allowed in Remanufactured Cylinder Packs for Certain C13 Engines{1218, 1225, 1239}
SH-56B Felling Head Felling Head Grapple Arm Spring - Assemble
773G and 775G Off-Highway Truck Hydraulic and Braking System Truck Body Mounting