Cylinder Head Valves
Show/hide table
图 1 | g02665396 |
Show/hide table
346-0485 缸盖总成 的技术规格     | |||
项目     | 数量     | 零件     | 技术规格说明     |
1     | 12     | 262-2957 进气门     | 装配缸盖气门前,使用清洁的发动机机油涂覆气门导管内径。     |
气门头直径为 41.50 ± 0.13 mm (1.634 ± 0.005 in)。 |
|||
表面角度为 29.50 ± 0.25 度。 | |||
2     | 12     | 255-8676 排气门     | 装配缸盖气门前,使用清洁的发动机机油涂覆气门导管内径。     |
气门头直径为 37.50 ± 0.13 mm (1.476 ± 0.005 in)。 |
|||
端面角度为 44.25 ± 0.25 度。 | |||
3     | 24     | 349-5307 弹簧     | 在试验力下的长度为 47.35 mm (1.864 in)。     |
试验力为 465.0 ± 23.3 N (104.5 ± 5.2 lb)。 |
|||
测试后的自由长度约为 77.9 mm (3.07 in)。 |
|||
4     | 24     | 349-5303 弹簧     | 在试验力下的长度为 46.15 mm (1.817 in)。     |
试验力为 232.5 ± 11.6 N (52.3 ± 2.6 lb)。 |
|||
测试后的自由长度约为 74.60 mm (2.937 in)。 |
|||
装配气门导管前,使用清洁的发动机机油涂覆用于安装气门导管的缸盖孔。     | |||
5     | 24     | 255-8665 气门导管     | 在缸盖的弹簧侧安装气门导管。 在气门导管安装到缸盖后,检查气门导管内径是否变形。     |
外径为 13.030 ± 0.008 mm (0.5130 ± 0.0003 in)。 |
|||
内径为 8.072 ± 0.013 mm (0.3178 ± 0.0005 in)。 |
|||
将气门导管装配到缸盖中后,在气门导管顶端安装密封。     | |||
A     |     | -     | 气门杆直径为 8.000 ± 0.010 mm (0.3150 ± 0.0004 in)。     |
Show/hide table
图 2 | g02665477 |
典型示例 |
Show/hide table
346-0485 缸盖总成 的技术规格     | |||
项目     | 数量     | 零件     | 技术规格说明     |
B     | -     | -     | 缸盖中用于安装进气门气门座镶圈的孔的深度为 9.30 ± 0.05 mm (0.366 ± 0.002 in)。     |
缸盖中用于安装排气门气门座镶圈的孔的深度为 10.40 ± 0.05 mm (0.409 ± 0.002 in)。 |
|||
C     | 24     | -     | 255-8666 进气门气门座镶圈 的直径为 42.560 ± 0.013 mm (1.6756 ± 0.0005 in)。     |
缸盖中用于安装进气门气门座镶圈的孔径为 42.500 ± 0.015 mm (1.6732 ± 0.0006 in)。 |
|||
262-2959 排气门气门座镶圈 的直径为 39.060 ± 0.013 mm (1.5378 ± 0.0005 in)。 |
|||
缸盖中用于安装排气门气门座镶圈的孔径为 39.000 ± 0.015 mm (1.5354 ± 0.0006 in)。 |
Caterpillar Information System:
R1300G Load Haul Dump Cooling System Coolant (DEAC) - Change
R1300G Load Haul Dump Cooling System Level - Check
SH-56B Felling Head Felling Head Grapple Arm Spring - Disassemble
422F, 428F, 432F, 434F and 444F Backhoe Loaders Cooling System Coolant Sample (Level 2) - Obtain
422F, 428F, 432F, 434F and 444F Backhoe Loaders Cooling System Coolant Sample (Level 1) - Obtain
773G and 775G Quarry Trucks Chassis Electronic Control System MID 087 - CID 0247 - FMI 09
422F, 428F, 432F, 434F and 444F Backhoe Loaders Cooling System Coolant Level - Check
422F, 428F, 432F, 434F and 444F Backhoe Loaders Cooling System Coolant (ELC) - Change
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Parking Brake - Remove and Install
428F, 432F, 434F and 444F Backhoe Loaders Cab Filter (Recirculation) - Clean/Inspect/Replace
2470C, 2570C and 2670C Wheel Feller Bunchers IQAN Monitoring ; Control System Service Tools
SH-56B Felling Head Felling Head Accumulator Arm - Assemble
R1300G Load Haul Dump Cooling System Coolant Extender (ELC) - Add
966H Wheel Loader and 972H Wheel Loader Electrohydraulic System Pilot Oil Accumulator (Dead Engine, Lift Arm Lower) - Test and Charge
C13, C15, and C18 Tier 4 Final Engines Cylinder Head
2013/08/21 Calculating Cylinder Liner Projection for 3500, 3500B, 3500C, and G3500 Engines {1201, 1216}
422F, 428F, 432F, 434F and 444F Backhoe Loaders Window Washer Reservoir - Fill
422F, 428F, 432F, 434F and 444F Backhoe Loaders Wheel Nut Torque - Check
2470C, 2570C and 2670C Wheel Feller Bunchers IQAN Monitoring ; Control System Diagnostic Capabilities
773G and 775G Quarry Trucks Chassis Electronic Control System MID 087 - CID 0248 - FMI 09
773G and 775G Quarry Trucks Chassis Electronic Control System MID 087 - CID 0420 - FMI 03
773G and 775G Quarry Trucks Chassis Electronic Control System MID 087 - CID 0420 - FMI 05
773G and 775G Quarry Trucks Chassis Electronic Control System MID 087 - CID 0420 - FMI 06
Installation Procedure for Front Heated Window Glass on Certain M, M Series 2, and M Series 3 Motor Graders {1408, 7305, 7310} Installation Procedure for Front Heated Window Glass on Certain M, M Series 2, and M Series 3 Motor Graders {1408, 7305, 7310}