Service and Parking Brake (Rear) - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
B     | 132-8159     | 液压扭矩扳手总成     | 1     |
203-5435 | 堆叠套筒     | 1     | |
132-8177 | 扳手连杆     | 1     | |
132-8223 | 液压泵和马达     | 1     | |
C     | 203-5435     | 堆叠套筒     | 1     |
Show/hide table
注意 |
---|
不正确组装零件或不遵守现有步骤会损坏零件和组件。 要避免零件损坏,请务必在零件上做识别标记,以便将其安装到原来的位置。 组装过程中,切勿强行安装零件。 |
Show/hide table
注意 |
---|
不遵循建议的步骤或不使用这些步骤所需的指定工具会导致零部件损坏。 要避免零部件损坏,请使用建议的工具并遵循建议的步骤。 |
- 检查所有 O 形密封圈和部件有无磨损或损坏。 如有必要,请更换部件。
注: 清洁度是一项重要的因素。 拆卸步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
- 利用所密封的润滑剂轻轻润滑所有 O 形密封圈。
- 安装 O 形密封圈 (3) 。
Show/hide table
图 1 | g00774009 |
- 将工具 (A) 连接在行车和停车制动器 (1) 上。 将工具 (A) 连接到适当的起吊设备上。
Show/hide table
图 2 | g00773969 |
Show/hide table
图 3 | g00773992 |
- 使用工具 (A) 和起吊设备安装行车和停车制动器 (1) 。 行车和停车制动器 (1) 的重量为 1587 kg (3492 lb)。
- 从行车和停车制动器 (1) 上卸下工具 (A) 。
- 使用工具 (B) 和工具 (C) 安装 34 颗螺母 (2) 和垫圈。 拧紧 34 颗螺母 (2) 至扭矩 3100 ± 350 N·m (2286 ± 258 lb ft)。
注: 工具 (B) 和工具 (C) 未显示。 将工具 (C) 置于靠近工具 (B) 的螺母上,然后用作工具 (B) 的反作用点。
End By: 安装后轮、轴承和 Duo-Cone 密封件。 请参阅 拆解和组装Duo-Cone, "后轮、轴承和 密封件 - 安装"。
Caterpillar Information System:
795F AC and 795F AC XQ Off-Highway Truck Machine Systems Service and Parking Brake (Rear) - Remove
2008/12/08 New Piston Assembly for the Main Hydraulic Pump for 345C Excavators {5070}
416E, 420E and 430E Backhoe Loaders Machine Systems Bank Valve (Loader) - Assemble - Mechanical 2 Bank Valve
795F and 795F Series AC Off-Highway Truck Power Train Truck Body Retaining Cable - Remove and Install
414E, 416E, 420E and 430E Backhoe Loaders Machine Systems Bank Valve (Loader) - Disassemble - Mechanical 2 Bank Valve
2008/10/13 New Procedure for Inspecting the TC900x Radios {733T}
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Systems Pilot Valve (Stabilizer) - Assemble
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Systems Pilot Valve (Stabilizer) - Disassemble
MINEGEM Machine Control ; Guidance Products LADAR Desiccant Cartridge - Inspect/Replace - R2900G JLK
MINEGEM Machine Control ; Guidance Products Power Supply Panel Isolation Switch
14M Motor Grader Axles May Generate Fine Copper Filings{4050} 14M Motor Grader Axles May Generate Fine Copper Filings{4050}
Noisy Steering Pilot Valve{4322, 5069, 5117} Noisy Steering Pilot Valve{4322, 5069, 5117}
795F AC and 795F AC XQ Off-Highway Truck Machine Systems Service and Parking Brake (Rear) - Disassemble
795F AC and 795F AC XQ Off-Highway Truck Machine Systems Service and Parking Brake (Rear) - Assemble
2008/12/01 A New Clamp Helps Prevent Leaks and Cracks {1000, 1350, 1380}
Procedure to Install the Horn Button{7332, 7402} Procedure to Install the Horn Button{7332, 7402}
24M Motor Grader Implement Electronic Control System MID 082 - CID 2747 - FMI 03
793F and 793F CMD Off-Highway Truck Power Train Engine Support
793F and 793F CMD Off-Highway Truck Power Train Window Wiper
Setup and Configuration for Health Interface Module (HIM) Diagnostic Tool
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Systems Bank Valve (Backhoe) - Disassemble - Mechanical 6 Bank, 7 Bank, or 8 Bank Valve
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Systems Bank Valve (Backhoe) - Assemble - Mechanical 6 Bank, 7 Bank, or 8 Bank Valve
793F and 793F CMD Off-Highway Truck Power Train Water Lines (Oil Coolers) - If Equipped
Bypass Valve Installation for Improved Cold Start{1386, 1387, 1408, 3154, 5057} Bypass Valve Installation for Improved Cold Start{1386, 1387, 1408, 3154, 5057}