PRODUCT IMPROVEMENT PROGRAM FOR REWORKING THE FUEL SYSTEM ON CERTAIN C27 AND C32 ELECTRIC POWER GENERATION UNITS OPERATING IN PRIME OR CONTINUOUS ENVIRONMENTS
Usage:
REBE7625-01
Show/hide table
| 20Oct2011 |
| (Revised 02Nov2011) |
U-454
A-373
D-402
O-402
Show/hide table
| Priority | PRODUCT IMPROVEMENT PROGRAM FOR REWORKING THE FUEL SYSTEM ON CERTAIN C27 AND C32 ELECTRIC POWER GENERATION UNITS OPERATING IN PRIME OR CONTINUOUS ENVIRONMENTS |
|
| 1250 1274 1920 | PI31934 |
|
Show/hide table
| NOTE: | This Program must be administered as soon as possible. When reporting the repair, use "PI31934" as the Part Number and "7751" as the Group Number, "56" as the Warranty Claim Description Code and "T" as the SIMS Description code. Exception: If the repair is done after failure, use "PI31934" as the Part Number, "7751" as the Group Number, "96" as the Warranty Claim Description Code, and "Z" as the SIMS Description Code. |
Show/hide table
| NOTE: | The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst. |
Show/hide table
Show/hide table
| NOTE: | This Revised Service Letter replaces the 20 October 2011 Service Letter. Changes have been made to the Affected Product. |
Show/hide table
COMPLETION DATE |
TERMINATION DATE |
| 30Apr2012 | 31Oct2012 |
PROBLEM
Show/hide table
| The existing front fuel supply hoses may not reach full life on engines operating in a prime or continuous environment. |
AFFECTED PRODUCT
Show/hide table
| Model | Identification Number |
| *******Group 1******* | |
| C27 | DWB00102, 109, 111, 122-124, 126, 129, 133-134, 146, 149, 151-155, 157-160, 167, 191, 197, 209, 216, 218, 221, 223-225, 227, 229, 231, 233, 236-237, 240, 242-244, 251, 264, 304, 306, 311, 316, 320, 322-324, 327-328, 330, 338, 350-351, 364, 366, 375, 461, 512, 540-541, 543, 568, 584, 590, 592, 594-595, 597, 638-640, 642-644, 651-652, 673, 675-676, 697, 699-700, 705, 743, 752, 765, 769, 806, 831, 891, 953-954 |
| C32 | K7C00103, 105-106 SXC00301, 303, 307, 309, 357, 360, 371, 377, 380, 382, 384, 387, 414, 426-428, 430-431, 434-440, 442-443, 466-468, 470-471, 473-481, 501, 514-515, 522-523, 534, 541, 545-546, 558-559, 588, 590, 615, 621, 627, 632-634, 640, 643, 648, 670, 673-674, 717, 725, 727-728, 730, 769, 772-773, 789-790, 813, 827, 836, 841-842, 844, 846, 849, 864, 872, 875-876, 884-888, 894, 914, 916, 918-921, 925, 930-931, 933-935, 937-940, 942-943, 945-950, 953-955, 957-960, 962-964, 966-967, 978, 980-982, 985, 992, 999-1000, 1008, 1015, 1017-1018, 1021-1022, 1026-1028, 1030-1032, 1034, 1051-1052, 1063, 1074, 1076-1081, 1090, 1092, 1095-1096, 1098, 1113, 1133-1134, 1137, 1139, 1141, 1143, 1145-1146, 1148-1149, 1151-1153, 1160-1164, 1170, 1172-1175, 1185-1188, 1190-1191, 1193-1194, 1196-1199, 1201, 1207-1208, 1210, 1212-1214, 1216, 1220, 1225, 1227, 1230-1231, 1238-1239, 1248-1249, 1251, 1253, 1262-1263, 1267, 1277-1278, 1281-1285, 1288, 1290-1291, 1300, 1308-1315, 1319-1324, 1327-1331, 1336, 1354, 1378, 1388-1390, 1399, 1401-1406, 1414-1418, 1424, 1426, 1428, 1434, 1436, 1438, 1440, 1442-1444, 1446-1448, 1454-1455, 1457, 1459-1460, 1465, 1469-1470, 1499-1500, 1503, 1508-1512, 1518-1519, 1521-1535, 1540, 1542, 1546, 1549-1550, 1553, 1555-1565, 1567-1581, 1593, 1613-1614, 1617, 1626-1627, 1630-1631, 1642, 1662, 1674-1677, 1681, 1683-1685, 1691-1692, 1699-1700, 1715, 1718, 1722, 1728-1729, 1735, 1741-1742, 1745, 1747-1748, 1756, 1760, 1767, 1770, 1783-1784, 1788, 1792, 1799, 1809, 1812, 1832-1833, 1840-1841, 1854, 1859, 1881, 1894, 1896, 1903, 1909-1911, 1914-1915, 1918, 1927-1928, 1939, 1951, 1964, 1973, 1983, 1994-1996, 2005, 2007-2008, 2013, 2026-2027, 2040-2045, 2047-2048, 2050-2051, 2056, 2058, 2071-2073, 2077, 2087, 2089, 2102, 2104, 2129-2131, 2133-2135, 2148-2151, 2154-2155, 2165, 2167-2170, 2172, 2175-2178, 2180, 2183, 2186-2187, 2195-2204, 2210, 2215, 2218-2221, 2226, 2228, 2230-2231, 2240, 2245, 2249, 2252, 2255, 2274, 2285, 2292, 2301, 2303-2306, 2310-2314, 2316, 2320-2325, 2347-2348, 2352, 2358-2359, 2361-2362, 2364, 2366, 2368-2369, 2371, 2377-2378, 2390, 2396-2398, 2410, 2416-2420, 2422, 2425-2426, 2437, 2439, 2451-2453, 2459, 2465-2468, 2470, 2473-2476, 2484, 2498-2502, 2510-2511, 2519, 2526-2528, 2549-2553, 2555, 2559, 2572-2576, 2587, 2589, 2592, 2594-2595, 2598-2599, 2624, 2637, 2659-2660, 2667, 2669, 2676, 2678, 2683-2684, 2686-2687, 2712-2713, 2716, 2783, 2790-2792, 2811, 2823, 2826-2827, 2829, 2842, 2853-2854, 2857-2858, 2867-2870, 2872-2873, 2930, 2951, 2953, 2956, 2958, 2982, 2991-2992, 2999, 3005-3006, 3017, 3020, 3025, 3036, 3039, 3042-3043, 3074, 3095, 3110, 3129-3131, 3139, 3143, 3157, 3182-3184, 3187, 3189, 3205, 3212, 3214, 3239, 3258-3260, 3262-3263, 3265, 3271, 3296-3299, 3302, 3305-3306, 3328-3329, 3338-3340, 3342-3343, 3345-3346, 3352-3353, 3374, 3379, 3402, 3414-3423, 3427-3431, 3434, 3445-3446, 3451, 3454, 3456, 3462-3464 |
| PMC32 | MED00100-00111, 113-115, 118-120, 123-125, 129, 143-144, 146, 156-157, 160, 162-163, 171, 174-176 |
Show/hide table
| *******Group 2******* | |
| C27 | DWB01025-01029, 1044, 1046, 1087-1089, 1094, 1111, 1113, 1116, 1124, 1143, 1147-1148, 1159, 1173, 1176, 1181, 1187, 1225, 1228, 1236, 1248-1255, 1261-1262, 1280, 1283-1284, 1293, 1309, 1314, 1319, 1324, 1332, 1339, 1343-1344, 1346, 1358, 1401, 1404, 1409, 1417, 1424, 1428, 1432, 1444-1446, 1463-1464, 1477, 1484-1486, 1488, 1490-1491, 1497, 1499-1500, 1505-1507, 1536, 1549, 1551-1555, 1561-1562, 1572, 1574, 1598, 1608 |
| C32 | K7C00110, 114-115, 119-121, 124-127, 131, 133, 135-136, 139-140, 143-145, 147, 150-162, 165, 169-174, 176, 180-181, 184, 188, 191, 194, 196-197, 200-202, 204 SXC03471, 3482, 3490, 3495, 3506, 3511, 3546, 3560, 3579, 3584-3586, 3610, 3622, 3632, 3635-3637, 3639, 3644-3645, 3647, 3654, 3657-3658, 3660-3661, 3664-3666, 3668, 3676, 3683-3684, 3690, 3692, 3700, 3724, 3726, 3753, 3763, 3767-3768, 3770, 3776, 3786, 3794, 3798, 3805, 3810-3811, 3839, 3849-3850, 3872-3873, 3889, 3897-3898, 3918-3919, 3928-3929, 3952-3954, 3958-3959, 3961, 3977, 3984, 3986, 3988, 3994, 3998-3999, 4019, 4021, 4030-4031, 4034, 4036, 4051-4053, 4060, 4064-4065, 4071, 4076, 4088-4089, 4097, 4114, 4123, 4135, 4167, 4175-4176, 4181, 4196, 4240-4241, 4247-4248, 4256, 4279-4280, 4283-4285, 4292, 4299, 4315-4317, 4339, 4342, 4344, 4346-4348, 4357, 4360, 4362, 4364, 4371, 4377-4379, 4398, 4401, 4416, 4426, 4444, 4454, 4458, 4466, 4473, 4476, 4489, 4500, 4505, 4522, 4524-4526, 4539-4540, 4544, 4547-4548, 4558, 4566-4567, 4574, 4577, 4579, 4598-4599, 4601-4604, 4646, 4649, 4659, 4680, 4683, 4692-4693, 4715-4717, 4722, 4726-4728, 4731-4734, 4741-4744, 4750, 4754, 4767, 4777, 4779-4780, 4785, 4819, 4825, 4830-4831, 4839-4843, 4847-4849, 4867-4868, 4890, 4895, 4911, 4917-4919, 4921-4922, 4936-4937, 4950, 4953, 4957, 4971, 4978, 5009, 5023, 5067, 5082, 5086, 5090, 5106-5108 |
| PMC32 | MED00179, 182-186 |
PARTS NEEDED
Show/hide table
Qty |
Part Number | Description |
| *******Group 1******* | ||
| 2 | 7V6571 | GROMMET (Before Failure Only) |
| 1 | 8C3089 | SEAL-O-RING (Before Failure Only) |
| 2 | 8T1889 | CLIP-2 PIECE (Before Failure Only) |
| 2 | 8T1890 | CLIP-2 PIECE (Before Failure Only) |
| 2 | 1473396 | CONNECTOR-PORT (Before Failure Only) |
| 2 | 2147568 | SEAL-O-RING-STOR (Before Failure Only) |
| 2 | 3227616 | HOSE AS. (Before Failure Only) |
| 1 | 3274448 | VALVE GP-CHECK-A (Before Failure Only) |
| 1 | 3394983 | KIT-SPRING (Before Failure Only) |
| 1 | 3459194 | SOFTWARE GP-ELEK (Before Failure Only) |
| 1 | 3459195 | SOFTWARE GP-ELEK (Before Failure Only) |
| 1 | 3459213 | SOFTWARE GP-ELEK (Before Failure Only) |
| 1 | 3459215 | SOFTWARE GP-ELEK (Before Failure Only) |
| 1 | 3459216 | SOFTWARE GP-ELEK (Before Failure Only) |
| 1 | 3459218 | SOFTWARE GP-ELEK (Before Failure Only) |
| 1 | 3459219 | SOFTWARE GP-ELEK (Before Failure Only) |
| 1 | 3459220 | SOFTWARE GP-ELEK (Before Failure Only) |
| In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 32% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer. | ||
| *******Group 2******* | ||
| 1 | 8C3089 | SEAL-O-RING (Before Failure Only) |
| 2 | 3227616 | HOSE AS. (Before Failure Only) |
| 1 | 3274448 | VALVE GP-CHECK-A (Before Failure Only) |
| 1 | 3394983 | KIT-SPRING (Before Failure Only) |
| 1 | 3459194 | SOFTWARE GP-ELEK (Before Failure Only) |
| 1 | 3459195 | SOFTWARE GP-ELEK (Before Failure Only) |
| 1 | 3459213 | SOFTWARE GP-ELEK (Before Failure Only) |
| 1 | 3459215 | SOFTWARE GP-ELEK (Before Failure Only) |
| 1 | 3459216 | SOFTWARE GP-ELEK (Before Failure Only) |
| 1 | 3459218 | SOFTWARE GP-ELEK (Before Failure Only) |
| 1 | 3459219 | SOFTWARE GP-ELEK (Before Failure Only) |
| 1 | 3459220 | SOFTWARE GP-ELEK (Before Failure Only) |
| In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 32% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer. | ||
ACTION REQUIRED
Show/hide table
| Rework the fuel system. 1. Increase the fuel pump pressure by reworking the transfer pump and pressure regulating valve. 2. Replace the front supply fuel lines. - Engines in Group 1: Add rubber grommeted clips. - Engines in Group 2: Only replace hoses. 3. Update the engine software. Refer to the attached Rework Procedure. Note: The front fuel hoses must be replaced on all engines on this service letter. Cavitation erosion has been known to damage the interior of the hose assembly. This damage is not externally observable. Note: Do not use Caterpillar HIS Information to fabricate the 322-7616 hoses. These hoses must be purchased from the Caterpillar Parts System as complete assemblies. |
Show/hide table
OWNER NOTIFICATION
Show/hide table
| U.S. and Canadian owners will receive the attached Owner Notification. |
SERVICE CLAIM ALLOWANCES
Show/hide table
| *******Group 1******* | |||||
| NOTE: This is a 4.5-hour job for Group 1 | |||||
Show/hide table
| *******Group 2******* | |||||
| NOTE: This is a 4.5-hour job for Group 2 | |||||
PARTS DISPOSITION
| Handle the parts in accordance with your Warranty Bulletin on warranty parts handling. MAKE EVERY EFFORT TO COMPLETE THIS PROGRAM AS SOON AS POSSIBLE. |
| MAKE EVERY EFFORT TO COMPLETE THIS PROGRAM AS SOON AS POSSIBLE. |
Show/hide table
| COPY OF OWNER NOTIFICATION FOR U.S. AND CANADIAN OWNERS XYZ Corporation 3240 Arrow Drive Anywhere, YZ 99999 PRIORITY - PRODUCT IMPROVEMENT PROGRAM FOR REWORKING THE FUEL SYSTEM ON CERTAIN C27 AND C32 ELECTRIC POWER GENERATION UNITS OPERATING IN PRIME OR CONTINUOUS ENVIRONMENTS MODELS INVOLVED - C27 and C32 ELECTRIC POWER GENERATION UNITS Dear Caterpillar Product Owner: The fuel system needs to be reworked on the products listed below. The existing front fuel supply hoses may not reach full life on engines operating in a prime or continuous environment. You will not be charged for the service performed. Contact your local Caterpillar dealer immediately to schedule this service. The dealer will advise you of the time required to complete this service. Please refer the dealer to their Service Letter dated 20Oct2011 when scheduling this service. We regret the inconvenience this may cause you, but urge you to have this service performed as soon as possible to prevent unscheduled downtime. Caterpillar Inc. Identification #(s) Attached to 20Oct2011 Service Letter |
| Group Number 1 |
| NOTE: Ensure the engine is shut down and steps have been taken to prevent any attempt to start the engine while fuel hoses are being updated. Use caution to ensure that no dirt enters the fuel port in the cylinder head. Damage to the fuel injectors could result. Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. NOTE: Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTE: Download the appropriate software as indicated by referencing the chart below (Image 1.1.1). If a given engine's software is not listed in this table, please refer to SISWEB or TMI for the latest available software. 1. Download the appropriate software prior to beginning the rework. |
 |
| Image1.1.1 |
| 2. Remove the existing front supply fuel hoses (2), standpipe port connectors (2) and hardware. Retain all mounting for reuse. Inspect the fuel hoses for chafing/abrasion damage. If observed, be sure to correct the issue when installing the new fuel hoses later. Pressure pulsations in these hoses cause them to flex. Inadvertent contact with nearby surfaces will produce chafing/abrasion damage that could eventually lead to a leak. |
| 3. Remove the 228-7381 Check Valve Group in the fuel return manifold (B), and replace with the 327-4448 Check Valve Group. Refer to Image1.3.1. 4. Remove the fuel transfer pump (A) located next to the fuel return manifold (B) as shown in Image1.3.1. |
 |
| Image1.3.1 |
| 5. Remove the Spring kit from the pump. Install the 339-4983 Spring Kit into the fuel transfer pump. Refer to Image1.4.1. The transfer pump has the old part number. By installing the 339-4983 Spring Kit, the pump has been upgraded to the new 331-3635 Transfer Pump. Mark the upgraded fuel pump with the new part number for later identification. |
 |
| Image1.4.1 |
| 6. Reinstall the fuel transfer pump using a new 8C-3089 O-ring. |
| 7. Remove existing port connector from the right side cylinder head and replace with new 147-3396 connector and 214-7568 O-ring seal. Tighten the connector to a torque of 34 +/- 3 N*m (25 +/- 2 lb ft). Install the right front fuel hose using a new 322-7616 Hose. The existing P-clip should be replaced with a rubber grommeted clip. Install a new 7V-6571 rubber grommet using an 8T-1889 and 8T-1890 two-piece clip mounted with existing bolt, washer, and spacer. Install clip mounted upward. Opening in the grommet must line up between gap in the 8T-1889 and 8T-1890 clips. Connect the 322-7616 fuel hose to the port connector and the tee, and tighten both ends to a torque of 27 +/- 6 N*m (20 +/- 4 lb ft). NOTE: Ensure the hoses do not contact nearby parts. Pressure pulsations in these hoses cause them to flex. Inadvertent contact with nearby surfaces will produce chafing/abrasion damage that could eventually lead to a leak. Note: If a metal part number tag is present, it must be removed after connecting the fuel hose. Failure to remove this metal tag can result in hose failure. Note: No cable tie fastening is allowed. |
 |
| Image1.6.1 |
| 8. Remove existing port connector from the left side cylinder head and replace with new 147-3396 connector and 214-7568 O-ring seal. Tighten the connector to a toque of 34 +/- 3 N*m (25 +/- 2 lb ft). Install the left front fuel hose using a new 322-7616 Hose. The existing P-clip should be replaced with a rubber grommeted clip. Install a new 7V-6571 rubber grommet using an 8T-1889 and 8T-1890 two-piece clip mounted with existing bolt and washer. Install clip mounted upward. Opening in the grommet must line up between gap in the 8T-1889 and 8T-1890 clips. Connect the 322-7616 fuel hose to the port connector and the tee and tighten both ends to a torque of 27 +/- 6 N*m (20 +/- 4 lb ft). NOTE: Ensure that the hoses do not contact nearby parts. Pressure pulsations in these hoses cause them to flex. Inadvertent contact with nearby surfaces will produce chafing/abrasion damage that could eventually lead to a leak. NOTE: If a metal part number tag is present, it must be removed after connecting the fuel hose. Failure to remove this metal tag can result in hose failure. NOTE: No cable tie fastening is allowed. |
 |
| Image1.7.1 |
| Group Number 2 |
| NOTE: Ensure the engine is shut down and steps have been taken to prevent any attempt to start the engine while fuel hoses are being updated. Use caution to ensure that no dirt enters the fuel port in the cylinder head. Damage to the fuel injectors could result. Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. NOTE: Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTE: Download the appropriate software as indicated by referencing the chart below (Image 2.1.1). If a given engine's software is not listed in this table, please refer to SISWEB or TMI for the latest available software. 1. Download the appropriate software prior to beginning the rework. |
 |
| Image2.1.1 |
| 2. Remove the existing front supply fuel hoses (2). Retain all hardware for reuse. Inspect the fuel hoses for chafing/abrasion damage. If observed, be sure to correct the issue when installing the new fuel hoses later. Pressure pulsations in these hoses cause them to flex. Inadvertent contact with nearby surfaces will produce chafing/abrasion damage that could eventually lead to a leak. |
| 3. Remove the 228-7381 Check Valve Group in the fuel return manifold (B), and replace with the 327-4448 Check Valve Group. Refer to Image2.3.1. 4. Remove the fuel transfer pump (A) located next to the fuel return manifold (B) as shown in Image2.3.1. |
 |
| Image2.3.1 |
| 5. Remove the Spring kit from the pump. Install the 339-4983 Spring Kit into the fuel transfer pump. Refer to Image2.4.1. The transfer pump has the old part number. By installing the 339-4983 Spring Kit, the pump has been upgraded to the new 331-3635 Transfer Pump. Mark the upgraded fuel pump with the new part number for later identification. |
 |
| Image2.4.1 |
| 6. Reinstall the fuel transfer pump using a new 8C-3089 O-ring. |
| 7. Install the right front fuel hose using a new 322-7616 Hose. The existing mounting hardware, rubber grommeted clips, and brackets should be reused. Openings in the grommets must line up between gap in the 8T-1889 and 8T-1890 clips. Connect the 322-7616 fuel hose to the port connector and the tee and tighten both ends to a torques of 27 +/- 6 N*m (20 +/- 4 lb ft). NOTE: Ensure the hoses do not contact nearby parts. Pressure pulsations in these hoses cause them to flex. Inadvertent contact with nearby surfaces will produce chafing/abrasion damage that could eventually lead to a leak. NOTE: If a metal part number tag is present, it must be removed after connecting the fuel hose. Failure to remove this metal tag can result in hose failure. NOTE: No cable tie fastening is allowed. |
 |
| Image2.6.1 |
| 8. Install the left front fuel hose using a new 322-7616 Hose. The existing mounting hardware, rubber grommeted clips, and brackets should be reused. Openings in the grommets must line up between gap in the 8T-1889 and 8T-1890 clips. Connect the 322-7616 fuel hose to the port connector and the tee and tighten both ends to a torque of 27 +/- 6 N*m (20 +/- 4 lb ft). NOTE: Ensure that the hoses do not contact nearby parts. Pressure pulsations in these hoses cause them to flex. Inadvertent contact with nearby surfaces will produce chafing/abrasion damage that could eventually lead to a leak. NOTE: If a metal part number tag is present, it must be removed after connecting the fuel hose. Failure to remove this metal tag can result in hose failure. NOTE: No cable tie fastening is allowed. |
 |
| Image2.7.1 |
Caterpillar Information System:
PRODUCT SUPPORT PROGRAM FOR FLASHING NEW SOFTWARE ON CERTAIN C9 INDUSTRIAL ENGINES PRODUCT SUPPORT PROGRAM FOR FLASHING NEW SOFTWARE ON CERTAIN C9 INDUSTRIAL ENGINES
PRODUCT SUPPORT PROGRAM FOR REPLACING THE BOLTS ON THE EXHAUST MANIFOLD Y CONNECTION ON CERTAIN C175 ELECTRIC POWER GENERATOR SETS PRODUCT SUPPORT PROGRAM FOR REPLACING THE BOLTS ON THE EXHAUST MANIFOLD Y CONNECTION ON CERTAIN C175 ELECTRIC POWER GENERATOR SETS
PRODUCT SUPPORT PROGRAM FOR UPDATING ENGINE CONTROL SOFTWARE ON CERTAIN C13 PETROLEUM ENGINES PRODUCT SUPPORT PROGRAM FOR UPDATING ENGINE CONTROL SOFTWARE ON CERTAIN C13 PETROLEUM ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE 124-3307 BALL BEARING IN THE B3 LOCATION ON CERTAIN TH55-E70 TRANSMISSIONS PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE 124-3307 BALL BEARING IN THE B3 LOCATION ON CERTAIN TH55-E70 TRANSMISSIONS
PRODUCT SUPPORT PROGRAM FOR REWORKING THE FUEL LINES, WIRING HARNESS, FUEL FILTER, ECM, ADDING AN EXHAUST TEMPERATURE SENSOR, AND UPDATING THE SOFTWARE ON CERTAIN C27 INDUSTRIAL ENGINES PRODUCT SUPPORT PROGRAM FOR REWORKING THE FUEL LINES, WIRING HARNESS, FUEL FILTER, ECM, ADDING AN EXHAUST TEMPERATURE SENSOR, AND UPDATING THE SOFTWARE ON CERTAIN C27 INDUSTRIAL ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR REMOVING THE 223-5252 FUEL PRIMING PUMP GROUPS FROM DEALER PARTS STOCK PRODUCT IMPROVEMENT PROGRAM FOR REMOVING THE 223-5252 FUEL PRIMING PUMP GROUPS FROM DEALER PARTS STOCK
PRODUCT SUPPORT PROGRAM FOR INSPECTING THE CLUSTER GEAR STUB SHAFT FLANGE BOLTS AND CLUSTER GEAR RETAINING PLATE BOLTS ON CERTAIN C175 GENERATOR SETS AND 793F , 793F XQ, 795F AC, 797F, 797F XQ OFF-HIGHWAY TRUCKS PRODUCT SUPPORT PROGRAM FOR INSPECTING THE CLUSTER GEAR STUB SHAFT FLANGE BOLTS AND CLUSTER GEAR RETAINING PLATE BOLTS ON CERTAIN C175 GENERATOR SETS AND 793F , 793F XQ, 795F AC, 797F, 797F XQ OFF-HIGHWAY TRUCKS
PRODUCT SUPPORT PROGRAM FOR INSTALLING SOFTWARE ON CERTAIN C12 MARINE ENGINES PRODUCT SUPPORT PROGRAM FOR INSTALLING SOFTWARE ON CERTAIN C12 MARINE ENGINES
PRODUCT SUPPORT PROGRAM FOR REPLACING THE FAN ADAPTER AND TENSIONER ASSEMBLY ON CERTAIN C9.3 INDUSTRIAL ENGINES PRODUCT SUPPORT PROGRAM FOR REPLACING THE FAN ADAPTER AND TENSIONER ASSEMBLY ON CERTAIN C9.3 INDUSTRIAL ENGINES
PRODUCT SUPPORT PROGRAM FOR REPLACING EXHAUST VALVES, GUIDES, AND SEALS ON CERTAIN C13 AND C15 ON-HIGHWAY ENGINES PRODUCT SUPPORT PROGRAM FOR REPLACING EXHAUST VALVES, GUIDES, AND SEALS ON CERTAIN C13 AND C15 ON-HIGHWAY ENGINES
PRODUCT SUPPORT PROGRAM FOR REPLACING THE NRS COOLER ON CERTAIN 349E EXCAVATORS, D8T TRACK-TYPE TRACTORS, 735B, 740B ARTICULATED TRUCKS, 980K WHEEL LOADERS, C15, AND C18 INDUSTRIAL ENGINES PRODUCT SUPPORT PROGRAM FOR REPLACING THE NRS COOLER ON CERTAIN 349E EXCAVATORS, D8T TRACK-TYPE TRACTORS, 735B, 740B ARTICULATED TRUCKS, 980K WHEEL LOADERS, C15, AND C18 INDUSTRIAL ENGINES
PRODUCT SUPPORT PROGRAM FOR REPLACING THE 242-8824 PRESSURE SENSOR GP ON CERTAIN G3606, G3608, G3612 AND G3616 ENGINES PRODUCT SUPPORT PROGRAM FOR REPLACING THE 242-8824 PRESSURE SENSOR GP ON CERTAIN G3606, G3608, G3612 AND G3616 ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING SOFTWARE ON MARINE POWERTRAIN CONTROL PROCESSORS PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING SOFTWARE ON MARINE POWERTRAIN CONTROL PROCESSORS
PRODUCT IMPROVEMENT PROGRAM FOR REMOVING CERTAIN 352-6061 LINER SEALS FOR 3500 ENGINES FROM DEALER PARTS STOCK PRODUCT IMPROVEMENT PROGRAM FOR REMOVING CERTAIN 352-6061 LINER SEALS FOR 3500 ENGINES FROM DEALER PARTS STOCK
PRODUCT SUPPORT PROGRAM FOR REPLACING CERTAIN PRINTED CIRCUIT BOARDS ON CERTAIN UPS 300, UPS 301, UPS 600, UPS 900, AND UPS 1200 UNINTERRUPTIBLE POWER SUPPLIES PRODUCT SUPPORT PROGRAM FOR REPLACING CERTAIN PRINTED CIRCUIT BOARDS ON CERTAIN UPS 300, UPS 301, UPS 600, UPS 900, AND UPS 1200 UNINTERRUPTIBLE POWER SUPPLIES
PRODUCT SUPPORT PROGRAM FOR REPLACING THE 243-1289 SUPPORT ON CERTAIN 3500 ENGINES PRODUCT SUPPORT PROGRAM FOR REPLACING THE 243-1289 SUPPORT ON CERTAIN 3500 ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR REMOVING CERTAIN 331-5291 AM/FM/WB/CD RADIO GP AND 331-5292 AM/FM RADIO GP FROM DEALER PARTS STOCK PRODUCT IMPROVEMENT PROGRAM FOR REMOVING CERTAIN 331-5291 AM/FM/WB/CD RADIO GP AND 331-5292 AM/FM RADIO GP FROM DEALER PARTS STOCK
PRODUCT SUPPORT PROGRAM FOR INSTALLING A 240 AMP ALTERNATOR ON CERTAIN C9.3 AND C13 INDUSTRIAL ENGINES PRODUCT SUPPORT PROGRAM FOR INSTALLING A 240 AMP ALTERNATOR ON CERTAIN C9.3 AND C13 INDUSTRIAL ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR REMOVING CERTAIN QUAD GAUGE MODULE GROUPS FROM DEALER PARTS STOCK PRODUCT IMPROVEMENT PROGRAM FOR REMOVING CERTAIN QUAD GAUGE MODULE GROUPS FROM DEALER PARTS STOCK
PRODUCT SUPPORT PROGRAM FOR REPLACING THE 304-3355 TORQUE CONVERTER INLET TUBE ASSEMBLY ON CERTAIN TH55-E70 FRAC TRANSMISSIONS PRODUCT SUPPORT PROGRAM FOR REPLACING THE 304-3355 TORQUE CONVERTER INLET TUBE ASSEMBLY ON CERTAIN TH55-E70 FRAC TRANSMISSIONS
PRODUCT SUPPORT PROGRAM FOR RELOCATING THE AIR INLET TEMPERATURE SENSOR ON CERTAIN C175 GENERATOR SETS PRODUCT SUPPORT PROGRAM FOR RELOCATING THE AIR INLET TEMPERATURE SENSOR ON CERTAIN C175 GENERATOR SETS
PRODUCT SUPPORT PROGRAM FOR REPAIRING AN OUTER VALVE SPRING FAILURE ON VARIOUS 3508, 3512 AND 3516 PETROLEUM ENGINES PRODUCT SUPPORT PROGRAM FOR REPAIRING AN OUTER VALVE SPRING FAILURE ON VARIOUS 3508, 3512 AND 3516 PETROLEUM ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING NEW ENGINE SOFTWARE ON CERTAIN 3500B LOCOMOTIVE ENGINES PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING NEW ENGINE SOFTWARE ON CERTAIN 3500B LOCOMOTIVE ENGINES
PRODUCT SUPPORT PROGRAM FOR REWORKING THE COOLING SYSTEM VENT LINE ON 3516B GENERATOR SETS PRODUCT SUPPORT PROGRAM FOR REWORKING THE COOLING SYSTEM VENT LINE ON 3516B GENERATOR SETS